Amin Shams Khorrami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amin Shams Khorrami has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Pouya Rezai
York University
2 shared publications Esmaeil Esmaeilzadeh
1 shared publicationFarhad Sadegh Moghanlou
1 shared publication- Habib Aminfar
Faculty of Mechanical Engineering, University of Tabriz, Tabriz, Iran
1 shared publication
Latest Publications
- 12 November 2018
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 14 (48) , 9870-9876
Oscillating dispersed-phase co-flow microfluidic droplet generation: jet length reduction effect
Microdroplet generation methods are assessed by two important criteria of droplet throughput and size dispersity. The widely-used co-flow droplet generation technique is bottlenecked with droplet polydispersity at high throughputs due to transition to an unstable jetting regime at high dispersed-phase (d-phase) flow rates. In this paper, we introduce a novel technique to oscillate the d-phase nozzle inside the continuous phase (c-phase) channel to suppress the jetting effect. The effect of the nozzle oscillation frequency (0–15 Hz) on the jet length was studied at different d-phase (Qd = 1.8, 2.4 and 3.0 ml min−1) and c-phase (Qc = 6, 12 and 18 ml min−1) flow rates and d-phase viscosities (1, 2.5, and 6 mPa s). The jet length was directly proportional to the d-phase flow rate and inversely proportional to the oscillation frequency. Oscillation-induced jet length reduction was more significant at high jet velocities, but a less steep jet length reduction was always observed at oscillation frequencies higher than 10 Hz. A maximum jet length reduction of 70.8% was obtained at the highest d-phase and lowest c-phase flow rates. Increasing the viscosity of the d-phase resulted in diminishing the effect of oscillation on jet length reduction. Moreover, we observed that nozzle oscillation could disintegrate the long jet into droplets of various sizes that were mostly smaller than the stationary-mode droplets. We hypothesize that oscillating the dispersion nozzle at lower flow rates, without the jetting effect, can simultaneously generate multi-size monodisperse droplets. This active technique can also be implemented into aqueous two-phase systems (ATPSs) in which droplet generation is a difficult task.
- 12 November 2018
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 14 (48) , 9870-9876
Oscillating dispersed-phase co-flow microfluidic droplet generation: jet length reduction effect
Microdroplet generation methods are assessed by two important criteria of droplet throughput and size dispersity. The widely-used co-flow droplet generation technique is bottlenecked with droplet polydispersity at high throughputs due to transition to an unstable jetting regime at high dispersed-phase (d-phase) flow rates. In this paper, we introduce a novel technique to oscillate the d-phase nozzle inside the continuous phase (c-phase) channel to suppress the jetting effect. The effect of the nozzle oscillation frequency (0–15 Hz) on the jet length was studied at different d-phase (Qd = 1.8, 2.4 and 3.0 ml min−1) and c-phase (Qc = 6, 12 and 18 ml min−1) flow rates and d-phase viscosities (1, 2.5, and 6 mPa s). The jet length was directly proportional to the d-phase flow rate and inversely proportional to the oscillation frequency. Oscillation-induced jet length reduction was more significant at high jet velocities, but a less steep jet length reduction was always observed at oscillation frequencies higher than 10 Hz. A maximum jet length reduction of 70.8% was obtained at the highest d-phase and lowest c-phase flow rates. Increasing the viscosity of the d-phase resulted in diminishing the effect of oscillation on jet length reduction. Moreover, we observed that nozzle oscillation could disintegrate the long jet into droplets of various sizes that were mostly smaller than the stationary-mode droplets. We hypothesize that oscillating the dispersion nozzle at lower flow rates, without the jetting effect, can simultaneously generate multi-size monodisperse droplets. This active technique can also be implemented into aqueous two-phase systems (ATPSs) in which droplet generation is a difficult task.
- 1 May 2018
- Published by AIP Publishing in Biomicrofluidics
- Vol. 12 (3) , 034113
Oscillating dispersed-phase co-flow microfluidic droplet generation: Multi-droplet size effect
Controllable generation of microdroplets at desired sizes and throughputs is important in many applications. Many biological assays require size-optimized droplets for effective encapsulation of analytes and reagents. To perform size optimization, different-size droplets must be generated from identical sources of samples to prevent potential cross-sample variations or other sources of error. In this paper, we introduce a novel alteration of the co-flow droplet generation technique to achieve multi-size generation of monodispersed droplets. Using a custom-made mechanism, we oscillate the disperse-phase (d-phase) flow nozzle perpendicular to the continuous phase (c-phase) flow in a co-flow channel. Oscillation of the d-phase nozzle introduces an additional lateral drag force to the growing droplets while exposing them to various levels of axial drag owing to the parabolic velocity distribution of the c-phase flow. Superimposing both effects results in simultaneous and repeatable generation of monodispersed droplets with different sizes. The effect of nozzle oscillation frequency (f = 0–15 Hz) on droplet generation at different d-phase (Qd = 0.05, 0.10, and 0.50 ml/min) and c-phase (Qc = 2, 5, and 10 ml/min) flow rates was studied. A wide range of monodispersed droplets (4nl–4 μl) were generated using this method. Droplet sizes were directly proportional to the We number and inversely proportional to the Ca number and oscillation frequency. Our technique is promising for applications such as aqueous two-phase systems, where due to inherently low interfacial tension, the d-phase flow forms a long stable jet which can be broken into droplets using the additional oscillatory drag in our device.
- 1 May 2018
- Published by AIP Publishing in Biomicrofluidics
- Vol. 12 (3) , 034113
Oscillating dispersed-phase co-flow microfluidic droplet generation: Multi-droplet size effect
Controllable generation of microdroplets at desired sizes and throughputs is important in many applications. Many biological assays require size-optimized droplets for effective encapsulation of analytes and reagents. To perform size optimization, different-size droplets must be generated from identical sources of samples to prevent potential cross-sample variations or other sources of error. In this paper, we introduce a novel alteration of the co-flow droplet generation technique to achieve multi-size generation of monodispersed droplets. Using a custom-made mechanism, we oscillate the disperse-phase (d-phase) flow nozzle perpendicular to the continuous phase (c-phase) flow in a co-flow channel. Oscillation of the d-phase nozzle introduces an additional lateral drag force to the growing droplets while exposing them to various levels of axial drag owing to the parabolic velocity distribution of the c-phase flow. Superimposing both effects results in simultaneous and repeatable generation of monodispersed droplets with different sizes. The effect of nozzle oscillation frequency (f = 0–15 Hz) on droplet generation at different d-phase (Qd = 0.05, 0.10, and 0.50 ml/min) and c-phase (Qc = 2, 5, and 10 ml/min) flow rates was studied. A wide range of monodispersed droplets (4nl–4 μl) were generated using this method. Droplet sizes were directly proportional to the We number and inversely proportional to the Ca number and oscillation frequency. Our technique is promising for applications such as aqueous two-phase systems, where due to inherently low interfacial tension, the d-phase flow forms a long stable jet which can be broken into droplets using the additional oscillatory drag in our device.
- 1 November 2014
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 59, 24-31
Experimental study on electrohydrodynamically induced heat transfer enhancement in a minichannel
- 1 November 2014
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 59, 24-31
Experimental study on electrohydrodynamically induced heat transfer enhancement in a minichannel