Eric Klinefelter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eric Klinefelter has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jeffrey A. Nanzer
Michigan State University
8 shared publications - Jason M. Merlo
Department of Electrical and Computer Engineering, Michigan State University, East Lansing, MI, USA
4 shared publications - Stavros Vakalis
Department of Electrical Engineering, University of South Florida, Tampa, FL, USA
3 shared publications - Hayder Radha
Michigan State University
1 shared publication - Liang Gong
School of Electrical Engineering and Telecommunications, University of New South Wales Sydney, Sydney, NSW, Australia
1 shared publication
Latest Publications
- 31 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (3) , 1562-1570
A Point Target Model for Interferometric Radar Angular Velocity Estimation
In this work, we derive the exact response of an interferometric correlation radar to an arbitrary scene containing N independent point scatterers. The response of an interferometric radar to multiple targets can be complicated by the nonlinear processing, which generates intermodulation responses in addition to the desired fundamental frequency responses. An accurate signal model is critical for predicting and mitigating these intermodulation products and allows for model-based parameter estimation methods to be used to estimate target angular velocity. We derive a general response to an arbitrary number of independent targets and validate both the exact model and a simpler approximate model via simulation and experimental measurement with a 38-GHz continuous-wave interferometric radar. The experiment contains two targets traveling perpendicular to the radar's line-of-sight on linear stages at speeds of 0.36 and 0.5 m/s. We use an error metric to describe the similarity between the measured or simulated time-frequency response and the time-frequency response of a signal generated using the frequency estimates of either the exact or approximate models and show that in regimes where the small-angle approximation holds, both models provide an accurate representation of the measured or simulated interferometric response, demonstrating the feasibility of these models.
- 31 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (3) , 1562-1570
A Point Target Model for Interferometric Radar Angular Velocity Estimation
In this work, we derive the exact response of an interferometric correlation radar to an arbitrary scene containing N independent point scatterers. The response of an interferometric radar to multiple targets can be complicated by the nonlinear processing, which generates intermodulation responses in addition to the desired fundamental frequency responses. An accurate signal model is critical for predicting and mitigating these intermodulation products and allows for model-based parameter estimation methods to be used to estimate target angular velocity. We derive a general response to an arbitrary number of independent targets and validate both the exact model and a simpler approximate model via simulation and experimental measurement with a 38-GHz continuous-wave interferometric radar. The experiment contains two targets traveling perpendicular to the radar's line-of-sight on linear stages at speeds of 0.36 and 0.5 m/s. We use an error metric to describe the similarity between the measured or simulated time-frequency response and the time-frequency response of a signal generated using the frequency estimates of either the exact or approximate models and show that in regimes where the small-angle approximation holds, both models provide an accurate representation of the measured or simulated interferometric response, demonstrating the feasibility of these models.
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (3) , 1674-1685
Three-Dimensional Velocity Measurement Using a Dual Axis Millimeter-Wave Interferometric Radar
In this work, a method for directly measuring target velocity in three dimensions using a dual axis correlation interferometric radar is presented. Recent advances have shown that the measurement of a target's angular velocity is possible by correlating the signals measured at spatially diverse aperture locations. By utilizing multiple orthogonal baselines and using conventional Doppler velocity methods to obtain radial velocity, a full 3-D velocity vector can be obtained using only three receive antennas and a single transmitter, without the need for tracking. A 41.8-GHz dual axis interferometric radar with a 7.26λ antenna baseline is presented along with measurements of a target moving parallel to the plane of the radar array, and of a target moving with components of both radial and tangential velocity. These experiments achieved total velocity root-mean-square errors (RMSEs) of 41.01 mm · s⁻¹ (10.5%) for a target moving along a plane parallel to the array, and 45.07 mm · s⁻¹ (13.5%) for a target moving with components of radial and tangential motion relative to the array; estimated trajectory angle RMSEs of 10.42° and 5.11° were achieved for each experiment.
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (3) , 1674-1685
Three-Dimensional Velocity Measurement Using a Dual Axis Millimeter-Wave Interferometric Radar
In this work, a method for directly measuring target velocity in three dimensions using a dual axis correlation interferometric radar is presented. Recent advances have shown that the measurement of a target's angular velocity is possible by correlating the signals measured at spatially diverse aperture locations. By utilizing multiple orthogonal baselines and using conventional Doppler velocity methods to obtain radial velocity, a full 3-D velocity vector can be obtained using only three receive antennas and a single transmitter, without the need for tracking. A 41.8-GHz dual axis interferometric radar with a 7.26λ antenna baseline is presented along with measurements of a target moving parallel to the plane of the radar array, and of a target moving with components of both radial and tangential velocity. These experiments achieved total velocity root-mean-square errors (RMSEs) of 41.01 mm · s⁻¹ (10.5%) for a target moving along a plane parallel to the array, and 45.07 mm · s⁻¹ (13.5%) for a target moving with components of radial and tangential motion relative to the array; estimated trajectory angle RMSEs of 10.42° and 5.11° were achieved for each experiment.
- Open Access
Three Dimensional Velocity Measurement Using a Dual Axis Millimeter-Wave Interferometric Radar
In this work, a method for directly measuring target velocity in three dimensions using a dual axis correlation interferometric radar is presented. Recent advances have shown that the measurement of a target's angular velocity is possible by correlating the signals measured at spatially diverse aperture locations. By utilizing multiple orthogonal baselines and using conventional Doppler velocity methods to obtain radial velocity, a full three-dimensional velocity vector can be obtained using only three receive antennas and a single transmitter, without the need for tracking. A $\text{41.8 GHz}$ dual axis interferometric radar with a $7.26\lambda$ antenna baseline is presented along with measurements of a target moving parallel to the plane of the radar array, and of a target moving with components of both radial and tangential velocity. These experiments achieved total velocity root-mean-square errors of $\text{41.01 mm}\cdot\text{s}^{-1}$ ($10.5\%$) for a target moving along a plane parallel to the array, and $\text{45.07 mm}\cdot\text{s}^{-1}$ ($13.5\%$) for a target moving with components of radial and tangential motion relative to the array; estimated trajectory angle RMSEs of $10.42^\circ$ and $5.11^\circ$ were achieved for each experiment respectively.Open AccessThree Dimensional Velocity Measurement Using a Dual Axis Millimeter-Wave Interferometric Radar
In this work, a method for directly measuring target velocity in three dimensions using a dual axis correlation interferometric radar is presented. Recent advances have shown that the measurement of a target's angular velocity is possible by correlating the signals measured at spatially diverse aperture locations. By utilizing multiple orthogonal baselines and using conventional Doppler velocity methods to obtain radial velocity, a full three-dimensional velocity vector can be obtained using only three receive antennas and a single transmitter, without the need for tracking. A $\text{41.8 GHz}$ dual axis interferometric radar with a $7.26\lambda$ antenna baseline is presented along with measurements of a target moving parallel to the plane of the radar array, and of a target moving with components of both radial and tangential velocity. These experiments achieved total velocity root-mean-square errors of $\text{41.01 mm}\cdot\text{s}^{-1}$ ($10.5\%$) for a target moving along a plane parallel to the array, and $\text{45.07 mm}\cdot\text{s}^{-1}$ ($13.5\%$) for a target moving with components of radial and tangential motion relative to the array; estimated trajectory angle RMSEs of $10.42^\circ$ and $5.11^\circ$ were achieved for each experiment respectively. - 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (8) , 937-940
A Multiple Baseline Interferometric Radar for Multiple Target Angular Velocity Measurement
We present a novel technique for directly estimating the angular velocities of multiple targets using multi-baseline millimeter-wave interferometric radar to significantly reduce nonlinear signal distortion caused when multiple targets are present. We show that through the multiplication of the normalized instantaneous frequency measurements across different baselines, nonlinear intermodulation products resulting from dual-antenna interferometric angular velocity measurements can be mitigated, producing only the terms corresponding to the angular velocity of the targets in the scene. To validate this, simulations were performed demonstrating the close agreement between the proposed method and an ideal correlation (without intermodulation distortion). Near-field errors resulting from far-field approximations are analyzed. Finally, experimental results of a three-antenna, three-baseline 38 GHz interferometric radar are presented that demonstrate the recovery of the motion of two oscillating pendulums of differing angular frequencies.
- 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (8) , 937-940
A Multiple Baseline Interferometric Radar for Multiple Target Angular Velocity Measurement
We present a novel technique for directly estimating the angular velocities of multiple targets using multi-baseline millimeter-wave interferometric radar to significantly reduce nonlinear signal distortion caused when multiple targets are present. We show that through the multiplication of the normalized instantaneous frequency measurements across different baselines, nonlinear intermodulation products resulting from dual-antenna interferometric angular velocity measurements can be mitigated, producing only the terms corresponding to the angular velocity of the targets in the scene. To validate this, simulations were performed demonstrating the close agreement between the proposed method and an ideal correlation (without intermodulation distortion). Near-field errors resulting from far-field approximations are analyzed. Finally, experimental results of a three-antenna, three-baseline 38 GHz interferometric radar are presented that demonstrate the recovery of the motion of two oscillating pendulums of differing angular frequencies.
- 3 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 1096-1104
Automotive Velocity Sensing Using Millimeter-Wave Interferometric Radar
In this article, we demonstrate the use of interferometric radar for high-accuracy measurement of the ground speed of a moving vehicle. Recent work has shown the capability of radar systems using interferometric antenna apertures to directly measure the angular velocity of objects. In this work, we apply this new measurement to the automotive application of velocity estimation. We start by formulating the interferometric response from a ground surface, which is modeled as a summation of independent point scatterers. Next, we present two velocity estimation methods: a Bayesian method that uses a signal model and a neural network-based approach. We then describe a 40-GHz interferometric radar system that we have developed and present on-vehicle measurements. Finally, we present the results of the two estimators and compare these results with the theoretical accuracy of the system. We show that the Bayesian and neural net estimators achieved a root-mean-square velocity error of 0.403 and 0.183 m/s, respectively.
- 3 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 1096-1104
Automotive Velocity Sensing Using Millimeter-Wave Interferometric Radar
In this article, we demonstrate the use of interferometric radar for high-accuracy measurement of the ground speed of a moving vehicle. Recent work has shown the capability of radar systems using interferometric antenna apertures to directly measure the angular velocity of objects. In this work, we apply this new measurement to the automotive application of velocity estimation. We start by formulating the interferometric response from a ground surface, which is modeled as a summation of independent point scatterers. Next, we present two velocity estimation methods: a Bayesian method that uses a signal model and a neural network-based approach. We then describe a 40-GHz interferometric radar system that we have developed and present on-vehicle measurements. Finally, we present the results of the two estimators and compare these results with the theoretical accuracy of the system. We show that the Bayesian and neural net estimators achieved a root-mean-square velocity error of 0.403 and 0.183 m/s, respectively.
- 4 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (3) , 304-307
Interferometric Microwave Radar With a Feedforward Neural Network for Vehicle Speed-Over-Ground Estimation
A novel approach to measuring the ground speed of autonomous vehicles using interferometric radar is presented. Using a microwave radar with interferometric processing and a feedforward neural network with local regression, high-accuracy velocity estimation is achieved with a downward-facing radar that, unlike forward-looking Doppler radars, can be protected from road debris and is, furthermore, unaffected by wheel slip and requires no external inputs, such as Global Navigation Satellite Systems (GNSS). A 16.9-GHz active interferometric array generates a grating lobe pattern and as the ground passes through the pattern, the range of frequencies over which the response is distributed increases proportionally with the ground velocity. We implement a feedforward neural network to estimate the velocity based on the interferometer's frequency response. The estimator achieved a root-mean-squared error of 0.138 (m/s), equivalent to that of the forward-looking Doppler radars.
- 4 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (3) , 304-307
Interferometric Microwave Radar With a Feedforward Neural Network for Vehicle Speed-Over-Ground Estimation
A novel approach to measuring the ground speed of autonomous vehicles using interferometric radar is presented. Using a microwave radar with interferometric processing and a feedforward neural network with local regression, high-accuracy velocity estimation is achieved with a downward-facing radar that, unlike forward-looking Doppler radars, can be protected from road debris and is, furthermore, unaffected by wheel slip and requires no external inputs, such as Global Navigation Satellite Systems (GNSS). A 16.9-GHz active interferometric array generates a grating lobe pattern and as the ground passes through the pattern, the range of frequencies over which the response is distributed increases proportionally with the ground velocity. We implement a feedforward neural network to estimate the velocity based on the interferometer's frequency response. The estimator achieved a root-mean-squared error of 0.138 (m/s), equivalent to that of the forward-looking Doppler radars.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-106
Angle Estimation Using an Active 38 GHz Interferometric Radar
The operation of a millimeter-wave interferometric radar for estimating the angle of a target is discussed in this paper. The transmitter emits a linear frequency modulated (LFM) signal, ranging from 37 GHz to 39 GHz. The millimeter-wave interferometric receiver is composed by two receive antenna elements separated by 51 cm (64.6λ). The number of sidelobes in the radiation pattern will change as a function of frequency, generating a frequency response that can be transformed to the angle of a target. The theory behind the technique is explained, supported by the experimental measurements.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-106
Angle Estimation Using an Active 38 GHz Interferometric Radar
The operation of a millimeter-wave interferometric radar for estimating the angle of a target is discussed in this paper. The transmitter emits a linear frequency modulated (LFM) signal, ranging from 37 GHz to 39 GHz. The millimeter-wave interferometric receiver is composed by two receive antenna elements separated by 51 cm (64.6λ). The number of sidelobes in the radiation pattern will change as a function of frequency, generating a frequency response that can be transformed to the angle of a target. The theory behind the technique is explained, supported by the experimental measurements.
- 16 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (11) , 1059-1061
Angle Estimation Using Wideband Frequency Modulation and an Active Distributed Array
A new method of target angle estimation, which leverages wideband waveforms and a distributed array receiver, is presented. The distributed array receiver generates a grating lobe pattern, the spatially distributed phase of which changes as a function of frequency. By implementing a wideband linear frequency modulated waveform, a phase response manifests in the distributed array receiver output, whose instantaneous frequency is proportional to the angle of the object. The receiver frequency response is derived, and the angle estimation approach is experimentally demonstrated. A 4.8-GHz distributed array radar was implemented with a receiver baseline of 19.36λ using a waveform modulated over 2 GHz of bandwidth. Measurements with a single-point target were conducted, and the measured frequency responses show the expected correspondence to the angle of the target with an average error of 2.8° (0.049 rad) and a standard deviation of 1.8° (0.031 rad).
- 16 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (11) , 1059-1061
Angle Estimation Using Wideband Frequency Modulation and an Active Distributed Array
A new method of target angle estimation, which leverages wideband waveforms and a distributed array receiver, is presented. The distributed array receiver generates a grating lobe pattern, the spatially distributed phase of which changes as a function of frequency. By implementing a wideband linear frequency modulated waveform, a phase response manifests in the distributed array receiver output, whose instantaneous frequency is proportional to the angle of the object. The receiver frequency response is derived, and the angle estimation approach is experimentally demonstrated. A 4.8-GHz distributed array radar was implemented with a receiver baseline of 19.36λ using a waveform modulated over 2 GHz of bandwidth. Measurements with a single-point target were conducted, and the measured frequency responses show the expected correspondence to the angle of the target with an average error of 2.8° (0.049 rad) and a standard deviation of 1.8° (0.031 rad).