Ken-Ichi Saitoh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ken-Ichi Saitoh has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Masanori Takuma
Department of Mechanical Engineering, Faculty of Engineering Science, Kansai University, Suita-shi 564-8680, Osaka, Japan
26 shared publications Tomohiro Sato
19 shared publicationsYoshimasa Takahashi
17 shared publications- Tomohiro Sato
Kansai University
13 shared publications - Yoshimasa Takahashi
Kansai University
11 shared publications Noboru Shinke
8 shared publications
Latest Publications
- Open Access
- 4 November 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 980
Effect of hydrogen absorption/desorption on mechanical strengths of polycrystalline palladium: mechanism of embrittlement
- 4 November 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 980
Open AccessEffect of hydrogen absorption/desorption on mechanical strengths of polycrystalline palladium: mechanism of embrittlement
- Open Access
- 4 November 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 745
Sensitivity of MD-based Taylor-Quinney coefficient estimates to thermodynamic ensemble and defect preconditioning
- 4 November 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 745
Open AccessSensitivity of MD-based Taylor-Quinney coefficient estimates to thermodynamic ensemble and defect preconditioning
- Open Access
- 28 September 2026
- Published by Springer Nature
- p. 394-400
Molecular Dynamics Simulation of Dislocations in Silicon Carbide (SiC) Crystal by Newly Developed Machine-Learning Potential
Machine-learning (ML) methodology was applied to the construction of a new interatomic potential for the silicon and carbon system for which any appropriate molecular dynamics (MD) potential is still lacking. It was done by collecting a number of ab initio calculation data (using density functional theory: DFT) of basic crystals: cubic 3C-SiC and hexagonal 4H-SiC crystals. As one of ML-potentials, the framework of SNAP (spectral neighbor analysis potential) was utilized. The performance of the new ML potential was evaluated for the reproduction of plastic behavior, that is, dislocation structure and motion in 3C-SiC crystal, as well as its basic lattice and elastic constants. It showed a certain availability as a potential for MD.
- 28 September 2026
- Published by Springer Nature
- p. 394-400
Open AccessMolecular Dynamics Simulation of Dislocations in Silicon Carbide (SiC) Crystal by Newly Developed Machine-Learning Potential
Machine-learning (ML) methodology was applied to the construction of a new interatomic potential for the silicon and carbon system for which any appropriate molecular dynamics (MD) potential is still lacking. It was done by collecting a number of ab initio calculation data (using density functional theory: DFT) of basic crystals: cubic 3C-SiC and hexagonal 4H-SiC crystals. As one of ML-potentials, the framework of SNAP (spectral neighbor analysis potential) was utilized. The performance of the new ML potential was evaluated for the reproduction of plastic behavior, that is, dislocation structure and motion in 3C-SiC crystal, as well as its basic lattice and elastic constants. It showed a certain availability as a potential for MD.
- Open Access
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Taylor-Quinney Coefficient Analysis using Molecular Dynamics- Effects of Thermodynamic Ensembles -
Accurate measurement of heat generation from plastic deformation work, i.e. the Taylor-Quinney coefficient (TQC: ), is difficult because heat conduction and thermal expansion can disturb the heat balance during deformation. Quantitative numerical analysis of TQC is therefore useful. Molecular dynamics (MD) simulation is a promising numerical method because the heat balance can be clearly measured. This work examines the influence of thermodynamic ensembles on MD-based TQC analysis in simple shear deformation of single-crystalline aluminium. To use a simple crystalline model while representing the pre-existing defects usually present in real materials, a three-stage deformation procedure, here denoted as Pre-Hold-Deform (P-H-D), was adopted. A pre-deformation and subsequent unloading/holding step introduce a stable defect-conditioned state before the deformation used for TQC evaluation, thereby reducing the influence of stress overshoot caused by homogeneous defect nucleation from an unrealistically defect-free crystal. TQC was calculated as the ratio of heat generation to plastic work, with the heat and work balances evaluated under NVE, NVT, NPH and NPT ensembles. The results show that, under the present conditions, the evaluated TQC under isochoric conditions (NVE or NVT) are larger than TQC under isobaric conditions (NPH or NPT). The comparison of ensembles provides useful guidance for assessing how thermal and mechanical boundary conditions affect TQC analysis.
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTaylor-Quinney Coefficient Analysis using Molecular Dynamics- Effects of Thermodynamic Ensembles -
Accurate measurement of heat generation from plastic deformation work, i.e. the Taylor-Quinney coefficient (TQC: ), is difficult because heat conduction and thermal expansion can disturb the heat balance during deformation. Quantitative numerical analysis of TQC is therefore useful. Molecular dynamics (MD) simulation is a promising numerical method because the heat balance can be clearly measured. This work examines the influence of thermodynamic ensembles on MD-based TQC analysis in simple shear deformation of single-crystalline aluminium. To use a simple crystalline model while representing the pre-existing defects usually present in real materials, a three-stage deformation procedure, here denoted as Pre-Hold-Deform (P-H-D), was adopted. A pre-deformation and subsequent unloading/holding step introduce a stable defect-conditioned state before the deformation used for TQC evaluation, thereby reducing the influence of stress overshoot caused by homogeneous defect nucleation from an unrealistically defect-free crystal. TQC was calculated as the ratio of heat generation to plastic work, with the heat and work balances evaluated under NVE, NVT, NPH and NPT ensembles. The results show that, under the present conditions, the evaluated TQC under isochoric conditions (NVE or NVT) are larger than TQC under isobaric conditions (NPH or NPT). The comparison of ensembles provides useful guidance for assessing how thermal and mechanical boundary conditions affect TQC analysis.
- 27 February 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40  (09n10)
Molecular dynamics simulation of plastic deformation in nano-sized plate: Atomic-scale super-elasticity and forming limit of pure copper single crystal
The forming process of nano-sized plate is investigated by using the molecular dynamics (MD) method as a microscopic theoretical analysis. Square-shaped plate models composed of single-crystal copper atoms with thicknesses of several nanometers (2–16 times the lattice constant of the face-centered cubic (FCC) lattice) are clamped by other rigid plates, and a rigid plug with cylindrical shape is pushing into the plate at a constant velocity. The forming limit diagram (FLD) obtained from atomic strains is successfully assessed. It is understood that dislocations and their motions play a crucial role in plastic deformation. The types and distribution of dislocations are compared for models with different crystal orientations of the surface, that is, {100}, {110} and {111} planes. The unloading process following the stoppage of the plug just before any breakage in the plate is also conducted. In unloading, extraordinary recovery of deformation close to 100 percent can be expected, particularly in very thin plate. It is concluded that the formability is the largest in {100} plane’s case and a thicker plate accompanies lower spring-back. It is also found in fracture behavior that initiation of defects in the plate occurs around icosahedral (ICO) structure, which does not match the FCC crystal nor the slip of dislocations.
- 27 February 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 40  (09n10)
Molecular dynamics simulation of plastic deformation in nano-sized plate: Atomic-scale super-elasticity and forming limit of pure copper single crystal
The forming process of nano-sized plate is investigated by using the molecular dynamics (MD) method as a microscopic theoretical analysis. Square-shaped plate models composed of single-crystal copper atoms with thicknesses of several nanometers (2–16 times the lattice constant of the face-centered cubic (FCC) lattice) are clamped by other rigid plates, and a rigid plug with cylindrical shape is pushing into the plate at a constant velocity. The forming limit diagram (FLD) obtained from atomic strains is successfully assessed. It is understood that dislocations and their motions play a crucial role in plastic deformation. The types and distribution of dislocations are compared for models with different crystal orientations of the surface, that is, {100}, {110} and {111} planes. The unloading process following the stoppage of the plug just before any breakage in the plate is also conducted. In unloading, extraordinary recovery of deformation close to 100 percent can be expected, particularly in very thin plate. It is concluded that the formability is the largest in {100} plane’s case and a thicker plate accompanies lower spring-back. It is also found in fracture behavior that initiation of defects in the plate occurs around icosahedral (ICO) structure, which does not match the FCC crystal nor the slip of dislocations.
- 11 November 2025
- Published by Springer Nature
- p. 169-187
Reduction of Cu-Ni-Si Alloy Powders Made by Water Atomization
- 11 November 2025
- Published by Springer Nature
- p. 169-187
Reduction of Cu-Ni-Si Alloy Powders Made by Water Atomization
- 3 April 2025
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 112
Change of microstructure and mechanical state in nano-sized wiredrawing: Molecular dynamics simulation of pure magnesium
- 3 April 2025
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 112
Change of microstructure and mechanical state in nano-sized wiredrawing: Molecular dynamics simulation of pure magnesium
- Open Access
- 22 October 2024
- Published by MDPI AG in Applied Mechanics
- Vol. 5  (4) , 731-744
Molecular Dynamics Analysis of Hydrogen Diffusion Behavior in Alpha-Fe Bi-Crystal Under Bending Deformation
The hydrogen embrittlement (HE) phenomenon occurring in drawn pearlitic steel wires sometimes results in dangerous delayed fracture and has been an important issue for a long time. HE is very sensitive to the amount of plastic deformation applied in the drawing process. Hydrogen (H) atom diffusion is affected by ambient thermal and mechanical conditions such as stress, pressure, and temperature. In addition, the influence of stress gradient (SG) on atomic diffusion is supposed to be crucial but is still unclear. Metallic materials undergoing plastic deformation naturally have SG, such as residual stresses, especially in inhomogeneous regions (e.g., surface or grain boundary). In this study, we performed molecular dynamics (MD) simulation using EAM potentials for Fe and H atoms and investigated the behavior of H atoms diffusing in pure iron (α-Fe) with the SG condition. Two types of SG conditions were investigated: an overall gradient established by a bending deformation of the specimen and an atomic-scale local gradient caused by the grain boundary (GB) structure. A bi-crystal model with H atoms and a GB structure was subjected to bending deformation. For a moderate flexure, bending stress is distributed linearly along the thickness of the specimen. The diffusion coefficient of H atoms in the bulk region increased with an increase in the SG value. In addition, it was clearly observed that the direction of diffusion was affected by the existence of the SG. It was found that diffusivity of the H atom is promoted by the reduction in its cohesive energy. From these MD results, we recognize an exponential relationship between the amount of H atom diffusion and the intensity of the SG in nano-sized bending deformation.
- 22 October 2024
- Published by MDPI AG in Applied Mechanics
- Vol. 5  (4) , 731-744
Open AccessMolecular Dynamics Analysis of Hydrogen Diffusion Behavior in Alpha-Fe Bi-Crystal Under Bending Deformation
The hydrogen embrittlement (HE) phenomenon occurring in drawn pearlitic steel wires sometimes results in dangerous delayed fracture and has been an important issue for a long time. HE is very sensitive to the amount of plastic deformation applied in the drawing process. Hydrogen (H) atom diffusion is affected by ambient thermal and mechanical conditions such as stress, pressure, and temperature. In addition, the influence of stress gradient (SG) on atomic diffusion is supposed to be crucial but is still unclear. Metallic materials undergoing plastic deformation naturally have SG, such as residual stresses, especially in inhomogeneous regions (e.g., surface or grain boundary). In this study, we performed molecular dynamics (MD) simulation using EAM potentials for Fe and H atoms and investigated the behavior of H atoms diffusing in pure iron (α-Fe) with the SG condition. Two types of SG conditions were investigated: an overall gradient established by a bending deformation of the specimen and an atomic-scale local gradient caused by the grain boundary (GB) structure. A bi-crystal model with H atoms and a GB structure was subjected to bending deformation. For a moderate flexure, bending stress is distributed linearly along the thickness of the specimen. The diffusion coefficient of H atoms in the bulk region increased with an increase in the SG value. In addition, it was clearly observed that the direction of diffusion was affected by the existence of the SG. It was found that diffusivity of the H atom is promoted by the reduction in its cohesive energy. From these MD results, we recognize an exponential relationship between the amount of H atom diffusion and the intensity of the SG in nano-sized bending deformation.
- 1 November 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 889
Time-dependent subcritical crack growth and its mechanism in Ni-based single crystal superalloys at 500 °C
- 1 November 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 889
Time-dependent subcritical crack growth and its mechanism in Ni-based single crystal superalloys at 500 °C
- Open Access
- 19 February 2023
- Published by MDPI AG in Applied Mechanics
- Vol. 4  (1) , 230-247
Shear Deterioration of the Hierarchical Structure of Cellulose Microfibrils under Water Condition: All-Atom Molecular Dynamics Analysis
This study aims to understand the mechanical properties of cellulose nanofibers (CNFs), a nano-sized material element of woods or plants. We develop all-atom (AA) molecular dynamics models of cellulose microfibrils (CMFs), which are the smallest constituent of CNFs. The models were designed for the process of structural failure or the degradation of a hierarchical material of multiple CMF fibers, due to shear deformation. It was assumed that two CMFs were arranged in parallel and in close contact, either in a vacuum or in water. The CMF models in water were built by surrounding AA-modeled water molecules with a few nanometers. Shear deformation was applied in the axial direction of the CMF or in the direction parallel to molecular sheets. Shear moduli were measured, and they agree with previous experimental and computational values. The presence of water molecules reduced the elastic modulus, because of the behavior of water molecules at the interface between CMFs as a function of temperature. In the inelastic region, the CMF often broke down inside CMFs in a vacuum condition. However, in water environments, two CMFs tend to slip away from each other at the interface. Water molecules act like a lubricant between multiple CMFs and promote smooth sliding.
- 19 February 2023
- Published by MDPI AG in Applied Mechanics
- Vol. 4  (1) , 230-247
Open AccessShear Deterioration of the Hierarchical Structure of Cellulose Microfibrils under Water Condition: All-Atom Molecular Dynamics Analysis
This study aims to understand the mechanical properties of cellulose nanofibers (CNFs), a nano-sized material element of woods or plants. We develop all-atom (AA) molecular dynamics models of cellulose microfibrils (CMFs), which are the smallest constituent of CNFs. The models were designed for the process of structural failure or the degradation of a hierarchical material of multiple CMF fibers, due to shear deformation. It was assumed that two CMFs were arranged in parallel and in close contact, either in a vacuum or in water. The CMF models in water were built by surrounding AA-modeled water molecules with a few nanometers. Shear deformation was applied in the axial direction of the CMF or in the direction parallel to molecular sheets. Shear moduli were measured, and they agree with previous experimental and computational values. The presence of water molecules reduced the elastic modulus, because of the behavior of water molecules at the interface between CMFs as a function of temperature. In the inelastic region, the CMF often broke down inside CMFs in a vacuum condition. However, in water environments, two CMFs tend to slip away from each other at the interface. Water molecules act like a lubricant between multiple CMFs and promote smooth sliding.