Mostafa Mohamed Ibrahim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mostafa Mohamed Ibrahim has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Ali Abd El Aziz Essa
Shaqra University
3 shared publications Mohamed Khaled
2 shared publicationsNabil H. Mostafa
2 shared publicationsAhmed F. AbdelGwad
1 shared publicationAhmed Farouk Abdel Gawad
Faculty of Engineering, Zagazig University, Zagazig, Egypt
1 shared publicationEmad Z. Ibrahim
1 shared publication
Latest Publications
- 1 March 2019
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 137, 138-160
A computational study of heat transfer analysis for a circular tube with conical ring turbulators
- 1 March 2019
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 137, 138-160
A computational study of heat transfer analysis for a circular tube with conical ring turbulators
- 1 November 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 144, 1056-1070
Heat transfer performance evaluation in circular tubes via internal repeated ribs with entropy and exergy analysis
- 1 November 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 144, 1056-1070
Heat transfer performance evaluation in circular tubes via internal repeated ribs with entropy and exergy analysis
- Open Access
- 16 June 2017
- Published by Science Publishing Group in American Journal of Modern Energy
- Vol. 3 (2) , 23-37
Aerodynamic Design and Blade Angle Analysis of a Small Horizontal–Axis Wind Turbine
The wind turbine blades are the main part of the rotor. Extraction of energy from wind depends on the design of the blade. In this paper, a design method based on Blade Element Momentum (BEM) theory is explained for small horizontal–axis wind turbine model (HAWT) blades. The method was used to optimize the chord and twist distributions of the wind turbine blades to enhance the aerodynamic performance of the wind turbine and consequently, increasing the generated power. A Fortran program was developed to use (BEM) in designing a model of Horizontal–Axis Wind Turbine (HAWT). NACA 4412 airfoil was selected for the design of the wind turbine blade. Computational fluid dynamics (CFD) analysis of HAWT blade cross section was carried out at various blade angles with the help of ANSYS Fluent. Present results are compared with other published results. Power generated from wind turbine increases with increasing blade angle due to the increase in air–velocity impact on the wind turbine blade. For blade angle change from 20° to 60°, the turbine power from wind has a small change and reaches the maximum when the blade angle equals to 90°. Thus, HAWT power depends on the blade profile and its orientation.
- 16 June 2017
- Published by Science Publishing Group in American Journal of Modern Energy
- Vol. 3 (2) , 23-37
Open AccessAerodynamic Design and Blade Angle Analysis of a Small Horizontal–Axis Wind Turbine
The wind turbine blades are the main part of the rotor. Extraction of energy from wind depends on the design of the blade. In this paper, a design method based on Blade Element Momentum (BEM) theory is explained for small horizontal–axis wind turbine model (HAWT) blades. The method was used to optimize the chord and twist distributions of the wind turbine blades to enhance the aerodynamic performance of the wind turbine and consequently, increasing the generated power. A Fortran program was developed to use (BEM) in designing a model of Horizontal–Axis Wind Turbine (HAWT). NACA 4412 airfoil was selected for the design of the wind turbine blade. Computational fluid dynamics (CFD) analysis of HAWT blade cross section was carried out at various blade angles with the help of ANSYS Fluent. Present results are compared with other published results. Power generated from wind turbine increases with increasing blade angle due to the increase in air–velocity impact on the wind turbine blade. For blade angle change from 20° to 60°, the turbine power from wind has a small change and reaches the maximum when the blade angle equals to 90°. Thus, HAWT power depends on the blade profile and its orientation.