Mostafa Hassani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mostafa Hassani has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Qi Tang
Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca, USA
8 shared publications - David Veysset
Massachusetts General Hospital and Harvard Medical School
7 shared publications - Jianxiong Li
Department of Materials Science and Engineering, The Ohio State University, Columbus, USA
5 shared publications Keith A. Nelson
Department of Chemistry, Massachusetts Institute of Technology 6 , 77 Massachusetts Avenue, Cambridge, Massachusetts 02139
5 shared publications- Christopher A. Schuh
Department of Materials Science and Engineering, Northwestern University, Evanston, USA
4 shared publications Yuan Yao
Cornell University
4 shared publications
Latest Publications
- 11 June 2026
- Published by Elsevier in Scripta Materialia
- Vol. 283
Mechanisms of oxide layer fracture during microparticle impact bonding
- 11 June 2026
- Published by Elsevier in Scripta Materialia
- Vol. 283
Mechanisms of oxide layer fracture during microparticle impact bonding
- Open Access
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Effect of grain size on impact and bonding behavior of metallic microparticles
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Open AccessEffect of grain size on impact and bonding behavior of metallic microparticles
- Open Access
- 9 January 2026
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 136 (1) , 016104
Smaller Grains Are Not Stronger: Microcrystalline Metals at Ultrahigh Strain Rates
The strength of metals and alloys increases as grain size decreases due to grain boundary strengthening. This “smaller is stronger” effect has been observed consistently in the microcrystalline, ultrafine-grained, and even nanocrystalline metals with the exception of extremely small grains on the order of ∼ 1 0 nm , where grain boundary strengthening breaks down. Here we report a reversed trend in the microcrystalline regime. When subjected to extremely high strain rates, metals with smaller grain sizes become softer. The grain sizes studied here (1– 1 0 0 μ m ) are several orders of magnitude larger than those associated with the breakdown of the grain boundary strengthening. We attribute this softening behavior to the suppression of ballistic dislocation transport, which, consequently, limits dislocation-phonon drag in smaller grains.
- 9 January 2026
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 136 (1) , 016104
Open AccessSmaller Grains Are Not Stronger: Microcrystalline Metals at Ultrahigh Strain Rates
The strength of metals and alloys increases as grain size decreases due to grain boundary strengthening. This “smaller is stronger” effect has been observed consistently in the microcrystalline, ultrafine-grained, and even nanocrystalline metals with the exception of extremely small grains on the order of ∼ 1 0 nm , where grain boundary strengthening breaks down. Here we report a reversed trend in the microcrystalline regime. When subjected to extremely high strain rates, metals with smaller grain sizes become softer. The grain sizes studied here (1– 1 0 0 μ m ) are several orders of magnitude larger than those associated with the breakdown of the grain boundary strengthening. We attribute this softening behavior to the suppression of ballistic dislocation transport, which, consequently, limits dislocation-phonon drag in smaller grains.
- 12 November 2025
- Published by Elsevier in Scripta Materialia
- Vol. 273
Deformation of metal-ceramic nanolaminates at extreme strain rates
- 12 November 2025
- Published by Elsevier in Scripta Materialia
- Vol. 273
Deformation of metal-ceramic nanolaminates at extreme strain rates
- 21 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 302
Particle size effect on supersonic impact-induced bond strength
- 21 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 302
Particle size effect on supersonic impact-induced bond strength
- 17 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59811-59819
Plastic deformation and strain rate sensitivity of chemically strengthened glass
- 17 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59811-59819
Plastic deformation and strain rate sensitivity of chemically strengthened glass
- 9 October 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1043
Grain size dependence of activation volume and strain rate sensitivity in FCC high entropy alloys
- 9 October 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1043
Grain size dependence of activation volume and strain rate sensitivity in FCC high entropy alloys
- 1 October 2025
- Published by Elsevier in Extreme Mechanics Letters
- Vol. 80
Precipitate response in GRCop-42 metallic microparticles under extreme impact conditions
- 1 October 2025
- Published by Elsevier in Extreme Mechanics Letters
- Vol. 80
Precipitate response in GRCop-42 metallic microparticles under extreme impact conditions
- Open Access
- 31 March 2025
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 122 (14)
Microparticle impact–induced bond strength in metals peaks with velocity
Supersonic impact of metallic microparticles onto metallic substrates generates extreme interfacial deformation and high contact pressures, enabling solid-state metallic bonding. Although higher impact velocities are generally believed to improve bond quality and mechanical properties in materials formed by supersonic impact deposition, here we report a peak in bond strength for single microparticle impact bonding, followed by a decline at higher impact velocities. Our in situ micromechanical measurements of interfacial strength for Al microparticles bonded to Al substrates reveal a three-fold increase from the critical bonding velocity (800 m/s) to a peak strength around 1,060 m/s. Interestingly, further increase in impact velocity results in a rapid decline in local interfacial strength. The decline continues up to the highest velocity studied, 1,337 m/s, which is well below the threshold required to induce melting or erosion. We show that a mechanistic transition from material strengthening to intensified elastic recovery is responsible for the peak strength in impact-induced bonding, with evidence linking the intensified elastic recovery to adiabatic softening at high impact velocities. Beyond 1,000 m/s for Al, interfacial damage induced by the intensified elastic recovery offsets the strength gain from higher impact velocities, resulting in a net decline in interfacial strength. This mechanistic understanding shall offer insights into the optimal design of processes that rely on impact bonding.
- 31 March 2025
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 122 (14)
Open AccessMicroparticle impact–induced bond strength in metals peaks with velocity
Supersonic impact of metallic microparticles onto metallic substrates generates extreme interfacial deformation and high contact pressures, enabling solid-state metallic bonding. Although higher impact velocities are generally believed to improve bond quality and mechanical properties in materials formed by supersonic impact deposition, here we report a peak in bond strength for single microparticle impact bonding, followed by a decline at higher impact velocities. Our in situ micromechanical measurements of interfacial strength for Al microparticles bonded to Al substrates reveal a three-fold increase from the critical bonding velocity (800 m/s) to a peak strength around 1,060 m/s. Interestingly, further increase in impact velocity results in a rapid decline in local interfacial strength. The decline continues up to the highest velocity studied, 1,337 m/s, which is well below the threshold required to induce melting or erosion. We show that a mechanistic transition from material strengthening to intensified elastic recovery is responsible for the peak strength in impact-induced bonding, with evidence linking the intensified elastic recovery to adiabatic softening at high impact velocities. Beyond 1,000 m/s for Al, interfacial damage induced by the intensified elastic recovery offsets the strength gain from higher impact velocities, resulting in a net decline in interfacial strength. This mechanistic understanding shall offer insights into the optimal design of processes that rely on impact bonding.
- Open Access
- 5 March 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 1-7
Suppressed ballistic transport of dislocations at strain rates up to 109 s–1 in a stable nanocrystalline alloy
- 5 March 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 1-7
Open AccessSuppressed ballistic transport of dislocations at strain rates up to 109 s–1 in a stable nanocrystalline alloy