Xaver Klemenschits
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xaver Klemenschits has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Lado Filipovic
TU Wien
3 shared publications - Siegfried Selberherr
Institute for Microelectronics, TU Wien, Vienna, Austria
3 shared publications - Alexander Toifl
Christian Doppler Laboratory for High Performance TCAD, Institute for Microelectronics, TU Wien, Wien, Austria
1 shared publication - Andreas Hössinger
Silvaco Europe Ltd
1 shared publication - Georg Strof
Global TCAD Solutions GmbH, Bösendorferstraße 1, Stiege 1, Top12, 1010 Vienna, Austria
1 shared publication - Josef Weinbub
Institute for Microelectronics, TU Wien, Gußhausstraße 27-29, 1040 Wien, Austria
1 shared publication
Latest Publications
- Open Access
- 16 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 665
Effect of Mask Geometry Variation on Plasma Etching Profiles
It is becoming quite evident that, when it comes to the further scaling of advanced node transistors, increasing the flash memory storage capacity, and enabling the on-chip integration of multiple functionalities, “there’s plenty of room at the top”. The fabrication of vertical, three-dimensional features as enablers of these advanced technologies in semiconductor devices is commonly achieved using plasma etching. Of the available plasma chemistries, SF6/O2 is one of the most frequently applied. Therefore, having a predictive model for this process is indispensable in the design cycle of semiconductor devices. In this work, we implement a physical SF6/O2 plasma etching model which is based on Langmuir adsorption and is calibrated and validated to published equipment parameters. The model is implemented in a broadly applicable in-house process simulator ViennaPS, which includes Monte Carlo ray tracing and a level set-based surface description. We then use the model to study the impact of the mask geometry on the feature profile, when etching through circular and rectangular mask openings. The resulting dimensions of a cylindrical hole or trench can vary greatly due to variations in mask properties, such as its etch rate, taper angle, faceting, and thickness. The peak depth for both the etched cylindrical hole and trench occurs when the mask is tapered at about 0.5°, and this peak shifts towards higher angles in the case of high passivation effects during the etch. The minimum bowing occurs at the peak depth, and it increases with an increasing taper angle. For thin-mask faceting, it is observed that the maximum depth increases with an increasing taper angle, without a significant variation between thin masks. Bowing is observed to be at a maximum when the mask taper angle is between 15° and 20°. Finally, the mask etch rate variation, describing the etching of different mask materials, shows that, when a significant portion of the mask is etched away, there is a notable increase in vertical etching and a decrease in bowing. Ultimately, the implemented model and framework are useful for providing a guideline for mask design rules.
- 16 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 665
Open AccessEffect of Mask Geometry Variation on Plasma Etching Profiles
It is becoming quite evident that, when it comes to the further scaling of advanced node transistors, increasing the flash memory storage capacity, and enabling the on-chip integration of multiple functionalities, “there’s plenty of room at the top”. The fabrication of vertical, three-dimensional features as enablers of these advanced technologies in semiconductor devices is commonly achieved using plasma etching. Of the available plasma chemistries, SF6/O2 is one of the most frequently applied. Therefore, having a predictive model for this process is indispensable in the design cycle of semiconductor devices. In this work, we implement a physical SF6/O2 plasma etching model which is based on Langmuir adsorption and is calibrated and validated to published equipment parameters. The model is implemented in a broadly applicable in-house process simulator ViennaPS, which includes Monte Carlo ray tracing and a level set-based surface description. We then use the model to study the impact of the mask geometry on the feature profile, when etching through circular and rectangular mask openings. The resulting dimensions of a cylindrical hole or trench can vary greatly due to variations in mask properties, such as its etch rate, taper angle, faceting, and thickness. The peak depth for both the etched cylindrical hole and trench occurs when the mask is tapered at about 0.5°, and this peak shifts towards higher angles in the case of high passivation effects during the etch. The minimum bowing occurs at the peak depth, and it increases with an increasing taper angle. For thin-mask faceting, it is observed that the maximum depth increases with an increasing taper angle, without a significant variation between thin masks. Bowing is observed to be at a maximum when the mask taper angle is between 15° and 20°. Finally, the mask etch rate variation, describing the etching of different mask materials, shows that, when a significant portion of the mask is etched away, there is a notable increase in vertical etching and a decrease in bowing. Ultimately, the implemented model and framework are useful for providing a guideline for mask design rules.
- Open Access
- 1 December 2021
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 386
Geometric advection and its application in the emulation of high aspect ratio structures
- 1 December 2021
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 386
Open AccessGeometric advection and its application in the emulation of high aspect ratio structures
- Open Access
- 22 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 115406-115422
The Level-Set Method for Multi-Material Wet Etching and Non-Planar Selective Epitaxy
We present numerical methods to enable accurate and robust level-set based simulation of anisotropic wet etching and non-planar epitaxy for semiconductor fabrication. These fabrication techniques are characterized by highly crystal orientation-dependent etch/growth rates, which lead to non-convex Hamiltonians in their description by the level-set equation. As a consequence, instable surface propagation may emerge, leading to unphysical results. We propose a calibration-free Stencil Lax-Friedrichs scheme and an advanced adaptive time-stepping approach, tailored to the level-set speed functions associated with anisotropic etching and epitaxy. The scheme calculates the numerical dissipation based on information about the local geometry and the nature of the etch rates/growth function, which enables an optimized trade-off between overly rounding of sharp geometric features and stable surface propagation. Furthermore, we introduce the deposition top layer method, which allows for robust handling of multiple material regions in non-planar epitaxy simulations. Both methods are demonstrated in a prototypical implementation, which is used to validate the capability and accuracy of our approaches. In particular, two-dimensional wet etching and three-dimensional epitaxy simulations are performed and characteristic geometry parameters are compared to the ideally expected values, showing robustness and high accuracy.
- 22 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 115406-115422
Open AccessThe Level-Set Method for Multi-Material Wet Etching and Non-Planar Selective Epitaxy
We present numerical methods to enable accurate and robust level-set based simulation of anisotropic wet etching and non-planar epitaxy for semiconductor fabrication. These fabrication techniques are characterized by highly crystal orientation-dependent etch/growth rates, which lead to non-convex Hamiltonians in their description by the level-set equation. As a consequence, instable surface propagation may emerge, leading to unphysical results. We propose a calibration-free Stencil Lax-Friedrichs scheme and an advanced adaptive time-stepping approach, tailored to the level-set speed functions associated with anisotropic etching and epitaxy. The scheme calculates the numerical dissipation based on information about the local geometry and the nature of the etch rates/growth function, which enables an optimized trade-off between overly rounding of sharp geometric features and stable surface propagation. Furthermore, we introduce the deposition top layer method, which allows for robust handling of multiple material regions in non-planar epitaxy simulations. Both methods are demonstrated in a prototypical implementation, which is used to validate the capability and accuracy of our approaches. In particular, two-dimensional wet etching and three-dimensional epitaxy simulations are performed and characteristic geometry parameters are compared to the ideally expected values, showing robustness and high accuracy.
- Open Access
- 29 November 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (12) , 631
Modeling of Gate Stack Patterning for Advanced Technology Nodes: A Review
Semiconductor device dimensions have been decreasing steadily over the past several decades, generating the need to overcome fundamental limitations of both the materials they are made of and the fabrication techniques used to build them. Modern metal gates are no longer a simple polysilicon layer, but rather consist of a stack of several different materials, often requiring multiple processing steps each, to obtain the characteristics needed for stable operation. In order to better understand the underlying mechanics and predict the potential of new methods and materials, technology computer aided design has become increasingly important. This review will discuss the fundamental methods, used to describe expected topology changes, and their respective benefits and limitations. In particular, common techniques used for effective modeling of the transport of molecular entities using numerical particle ray tracing in the feature scale region will be reviewed, taking into account the limitations they impose on chemical modeling. The modeling of surface chemistries and recent advances therein, which have enabled the identification of dominant etch mechanisms and the development of sophisticated chemical models, is further presented. Finally, recent advances in the modeling of gate stack pattering using advanced geometries in the feature scale are discussed, taking note of the underlying methods and their limitations, which still need to be overcome and are actively investigated.
- 29 November 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (12) , 631
Open AccessModeling of Gate Stack Patterning for Advanced Technology Nodes: A Review
Semiconductor device dimensions have been decreasing steadily over the past several decades, generating the need to overcome fundamental limitations of both the materials they are made of and the fabrication techniques used to build them. Modern metal gates are no longer a simple polysilicon layer, but rather consist of a stack of several different materials, often requiring multiple processing steps each, to obtain the characteristics needed for stable operation. In order to better understand the underlying mechanics and predict the potential of new methods and materials, technology computer aided design has become increasingly important. This review will discuss the fundamental methods, used to describe expected topology changes, and their respective benefits and limitations. In particular, common techniques used for effective modeling of the transport of molecular entities using numerical particle ray tracing in the feature scale region will be reviewed, taking into account the limitations they impose on chemical modeling. The modeling of surface chemistries and recent advances therein, which have enabled the identification of dominant etch mechanisms and the development of sophisticated chemical models, is further presented. Finally, recent advances in the modeling of gate stack pattering using advanced geometries in the feature scale are discussed, taking note of the underlying methods and their limitations, which still need to be overcome and are actively investigated.