Meisheng Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Meisheng Yang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Bing Xu
Zhejiang University
2 shared publications - Junhui Zhang
Zhejiang University
2 shared publications Bing Xu
1 shared publication- Changwei Zhang
Anhui University of Technology
1 shared publication Chao Cao
1 shared publicationDongdong Li
1 shared publication
Latest Publications
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Multi-Physics Coupling Analysis and Multi-Objective Optimization Design of the High-Speed Solenoid Valve
To enhance the overall performance and operational reliability of a high-speed solenoid valve under complex operating conditions, a multi-physics coupling analysis and multi-objective optimization were carried out. First, a structural model of the valve was established, and its static electromagnetic and steady-state flow characteristics were analyzed to reveal the variations in electromagnetic force, internal pressure, and flow velocity. Then, a magneto-thermal-fluid-structural coupling model was developed, in which electromagnetic loss was introduced into the thermal field as a heat source, enabling further investigation of the temperature rise and deformation behaviors of key components under combined thermal and fluid loads. Finally, key structural parameters were selected as design variables, while electromagnetic performance, thermal safety, and structural reliability were taken as optimization objectives. The results indicate that the geometric parameters of the armature and stationary core significantly affect the electromagnetic force, whereas the valve opening has a pronounced influence on the steady hydraulic force and flow characteristics. Under coupled operating conditions, the maximum temperature and deformation reach approximately 55 °C and 30 µm, respectively, both mainly concentrated in the contact region. A set of Pareto-optimal solutions was obtained using the Kriging surrogate model and a multi-objective genetic algorithm. The results showed that after optimization, the maximum temperature decreased from 54.04 ℃ to 39.83 ℃, a decrease of about 26.3%, while meeting the requirement of electromagnetic force greater than 40 N for driving; The maximum deformation decreased from 13.4 µm to 7.9 µm, a decrease of approximately 41.0%.
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMulti-Physics Coupling Analysis and Multi-Objective Optimization Design of the High-Speed Solenoid Valve
To enhance the overall performance and operational reliability of a high-speed solenoid valve under complex operating conditions, a multi-physics coupling analysis and multi-objective optimization were carried out. First, a structural model of the valve was established, and its static electromagnetic and steady-state flow characteristics were analyzed to reveal the variations in electromagnetic force, internal pressure, and flow velocity. Then, a magneto-thermal-fluid-structural coupling model was developed, in which electromagnetic loss was introduced into the thermal field as a heat source, enabling further investigation of the temperature rise and deformation behaviors of key components under combined thermal and fluid loads. Finally, key structural parameters were selected as design variables, while electromagnetic performance, thermal safety, and structural reliability were taken as optimization objectives. The results indicate that the geometric parameters of the armature and stationary core significantly affect the electromagnetic force, whereas the valve opening has a pronounced influence on the steady hydraulic force and flow characteristics. Under coupled operating conditions, the maximum temperature and deformation reach approximately 55 °C and 30 µm, respectively, both mainly concentrated in the contact region. A set of Pareto-optimal solutions was obtained using the Kriging surrogate model and a multi-objective genetic algorithm. The results showed that after optimization, the maximum temperature decreased from 54.04 ℃ to 39.83 ℃, a decrease of about 26.3%, while meeting the requirement of electromagnetic force greater than 40 N for driving; The maximum deformation decreased from 13.4 µm to 7.9 µm, a decrease of approximately 41.0%.
- 10 February 2026
- Published by Elsevier in Measurement
- Vol. 269
Dynamic characteristics measurement of a novel high-pressure large-flow water hydraulic proportional flow valve driven by high-speed switching valves
- 10 February 2026
- Published by Elsevier in Measurement
- Vol. 269
Dynamic characteristics measurement of a novel high-pressure large-flow water hydraulic proportional flow valve driven by high-speed switching valves
- 1 June 2023
- Published by Springer Nature
- p. 179-199
Optimal Study for Multi-field Coupling of the Disc Brake Based on Kriging Agent Model
- 1 June 2023
- Published by Springer Nature
- p. 179-199
Optimal Study for Multi-field Coupling of the Disc Brake Based on Kriging Agent Model
- Open Access
- 23 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
Simulation Research on Thermal Characteristics and Experimental Study on Electronic Control Board of the Miniature High-Speed Digital Valve
The miniature high-speed digital valve is essentially a kind of miniature system that contains many nonlinear factors and involves multifield coupling among electromagnetic, mechanical, and liquid ones. In this study, the dimension of an electromagnetic structure is normalized into a unified variable, and the numerical analysis method is used to optimize the values of each parameter size on the premise of satisfying the requirements. The electronic control board is the control signal input equipment of the valve. The input changes of voltage and current directly affect the thermal characteristics of the valve. The electronic control board is the power source of the digital valves, and their high speed partially depends on the characteristics of the electronic control board. In this study, a control board for miniature digital valves was developed, which realizes the rapid rise and fall of current and meets the design requirements. A new electronic control board is manufactured, and a control platform for the electronic control board is built. Experiments demonstrate that there is no delay in the current rise and fall, showing that the valve achieves its dynamic response target. Using the finite element analysis software Workbench to simulate it numerically, the temperature field distribution in the original structure is not uniform, which affects the magnetic properties of the electromagnetic field. To address this disadvantage, this study proposes to insulate the heat source with thermal insulation material, which will not affect the temperature distribution of the entire electromagnetic components. The simulations show that the proposed method is effective and reliable.
- 23 May 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
Open AccessSimulation Research on Thermal Characteristics and Experimental Study on Electronic Control Board of the Miniature High-Speed Digital Valve
The miniature high-speed digital valve is essentially a kind of miniature system that contains many nonlinear factors and involves multifield coupling among electromagnetic, mechanical, and liquid ones. In this study, the dimension of an electromagnetic structure is normalized into a unified variable, and the numerical analysis method is used to optimize the values of each parameter size on the premise of satisfying the requirements. The electronic control board is the control signal input equipment of the valve. The input changes of voltage and current directly affect the thermal characteristics of the valve. The electronic control board is the power source of the digital valves, and their high speed partially depends on the characteristics of the electronic control board. In this study, a control board for miniature digital valves was developed, which realizes the rapid rise and fall of current and meets the design requirements. A new electronic control board is manufactured, and a control platform for the electronic control board is built. Experiments demonstrate that there is no delay in the current rise and fall, showing that the valve achieves its dynamic response target. Using the finite element analysis software Workbench to simulate it numerically, the temperature field distribution in the original structure is not uniform, which affects the magnetic properties of the electromagnetic field. To address this disadvantage, this study proposes to insulate the heat source with thermal insulation material, which will not affect the temperature distribution of the entire electromagnetic components. The simulations show that the proposed method is effective and reliable.
- Open Access
- 4 June 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (6) , 283
Design and Experimental Research of a Miniature Digital Hydraulic Valve
A digital hydraulic valve is an important component of the digital hydraulic system, and its performance is directly related to the system function. In order to make the valve system more competitive in dimension, digital valve miniaturization is an important research point. A new micro digital valve is designed, which is analyzed from the mechanical structure and magnetic circuit mechanism, and the design difficulties are also expounded. The four subsystems and switching characteristics of the valve are theoretically analyzed and simulated. In order to test the performance of the valve, a test system is designed, and performance of the new micro valve is tested. The test results show that the switch characteristic analysis of the valve is correct. The comparison between the test curve and the simulation curve is carried out, which demonstrates that the accuracy of the simulation model is reasonable. The theoretical analysis of the new micro digital valve is consistent with experiments.
- 4 June 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (6) , 283
Open AccessDesign and Experimental Research of a Miniature Digital Hydraulic Valve
A digital hydraulic valve is an important component of the digital hydraulic system, and its performance is directly related to the system function. In order to make the valve system more competitive in dimension, digital valve miniaturization is an important research point. A new micro digital valve is designed, which is analyzed from the mechanical structure and magnetic circuit mechanism, and the design difficulties are also expounded. The four subsystems and switching characteristics of the valve are theoretically analyzed and simulated. In order to test the performance of the valve, a test system is designed, and performance of the new micro valve is tested. The test results show that the switch characteristic analysis of the valve is correct. The comparison between the test curve and the simulation curve is carried out, which demonstrates that the accuracy of the simulation model is reasonable. The theoretical analysis of the new micro digital valve is consistent with experiments.
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Experimental Study and Simulation Analysis on Electromagnetic Characteristics and Dynamic Response of a New Miniature Digital Valve
In order to get the better electromagnetic characteristics of the micro digital valve, the larger electromagnetic force should be obtained in the smaller electromagnetic structure. The electromagnetic force directly determines the electromagnetic properties of the miniature digital valve. The electromagnetic force test is studied in the paper. The results of electromagnetic simulation results are basically consistent with the experimental results. The simulation model is reliable and accurate. The dynamic simulation results show that the dynamic characteristics of the miniature digital valve meet the requirements of the digital hydraulic technology. Design of the new micro digital valve is reasonable.
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Open AccessExperimental Study and Simulation Analysis on Electromagnetic Characteristics and Dynamic Response of a New Miniature Digital Valve
In order to get the better electromagnetic characteristics of the micro digital valve, the larger electromagnetic force should be obtained in the smaller electromagnetic structure. The electromagnetic force directly determines the electromagnetic properties of the miniature digital valve. The electromagnetic force test is studied in the paper. The results of electromagnetic simulation results are basically consistent with the experimental results. The simulation model is reliable and accurate. The dynamic simulation results show that the dynamic characteristics of the miniature digital valve meet the requirements of the digital hydraulic technology. Design of the new micro digital valve is reasonable.
- 1 December 2013
- Published by Elsevier in Mechatronics
- Vol. 23 (8) , 1180-1190
Safety brake performance evaluation and optimization of hydraulic lifting systems in case of overspeed dropping
- 1 December 2013
- Published by Elsevier in Mechatronics
- Vol. 23 (8) , 1180-1190
Safety brake performance evaluation and optimization of hydraulic lifting systems in case of overspeed dropping