Junliang Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Junliang Ding has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bohan Wang
Aeronautics Engineering College, Air Force Engineering University, Xi’an 710038, China
2 shared publications - Li Cheng
Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hong Kong, China
2 shared publications - Changkai Wang
Air Force Engineering University, Xi'an 710038, China
1 shared publication Dongchun Li
Aeronautic Engineering College, Airforce Engineering University, Xi’an 710038, China
1 shared publication- Jingyuan Liu
Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001, China
1 shared publication - Lin Zeng
Aeronautic Engineering College, Airforce Engineering University, Xi’an 710038, China
1 shared publication
Latest Publications
- Open Access
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2012 (1) , 012032
Very High Cycle Fatigue Properties of 2024 Aluminum Alloy Samples in Three Sizes
An ultrasonic fatigue testing system was used to carry out very high cycle fatigue (VHCF) tests on 2024 aluminum alloy in three different sizes of specimens. The influence of specimen size and optimization on the experimental results was discussed and the VHCF properties of 2024 aluminum alloy were obtained at the same time. The results show that: The S-N curves of all specimens show a continuous decreasing tendency and the curve of the dog-bone-shaped specimen (the half-length of the testing volume L0 > 0) is lower than that of the hourglass-shaped specimen (L0 = 0) at low-cycle and high-cycle fatigue stages, which is opposite at the VHCF stage; The optimized specimen solves the problem of fracture position deviation and effectively improves the accuracy of experimental data; 2024 aluminum alloy will still fracture when the fatigue life exceed 107, and there exist no fatigue limit; All cracks initiate at surface and the fracture morphologies show characteristics of the crack initiation and propagation.
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2012 (1) , 012032
Open AccessVery High Cycle Fatigue Properties of 2024 Aluminum Alloy Samples in Three Sizes
An ultrasonic fatigue testing system was used to carry out very high cycle fatigue (VHCF) tests on 2024 aluminum alloy in three different sizes of specimens. The influence of specimen size and optimization on the experimental results was discussed and the VHCF properties of 2024 aluminum alloy were obtained at the same time. The results show that: The S-N curves of all specimens show a continuous decreasing tendency and the curve of the dog-bone-shaped specimen (the half-length of the testing volume L0 > 0) is lower than that of the hourglass-shaped specimen (L0 = 0) at low-cycle and high-cycle fatigue stages, which is opposite at the VHCF stage; The optimized specimen solves the problem of fracture position deviation and effectively improves the accuracy of experimental data; 2024 aluminum alloy will still fracture when the fatigue life exceed 107, and there exist no fatigue limit; All cracks initiate at surface and the fracture morphologies show characteristics of the crack initiation and propagation.
- Open Access
- 1 September 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1637 (1) , 012139
Effect of Laser Shock Strengthening on Modal Frequency
The phenomenon of laser shock strengthening (LSP) changing the resonance frequency of a structure can be used to adjust the frequency of aero-engine blades, and has a broad application prospect. In this paper, through the combination of mechanical analysis, numerical simulation and vibration test, the effect of LSP technology on structural vibration characteristics is studied. The influence mechanism of local stiffness changes on the modal frequency of the structure is analyzed from the perspective of vibration and energy. It is found that when the laser shock is strengthened in a region with large bending deformation, the greater the contribution to the overall modal stiffness and elastic potential energy, the greater the modal frequency. The impact is also greater. Established a mapping relationship among laser shock strengthening, local stiffness and modal frequency, and finally proved that LSP technology can significantly change the local elastic modulus of TC4 titanium alloy, which provides a reliable application of the technology in the production department Theoretical support.
- 1 September 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1637 (1) , 012139
Open AccessEffect of Laser Shock Strengthening on Modal Frequency
The phenomenon of laser shock strengthening (LSP) changing the resonance frequency of a structure can be used to adjust the frequency of aero-engine blades, and has a broad application prospect. In this paper, through the combination of mechanical analysis, numerical simulation and vibration test, the effect of LSP technology on structural vibration characteristics is studied. The influence mechanism of local stiffness changes on the modal frequency of the structure is analyzed from the perspective of vibration and energy. It is found that when the laser shock is strengthened in a region with large bending deformation, the greater the contribution to the overall modal stiffness and elastic potential energy, the greater the modal frequency. The impact is also greater. Established a mapping relationship among laser shock strengthening, local stiffness and modal frequency, and finally proved that LSP technology can significantly change the local elastic modulus of TC4 titanium alloy, which provides a reliable application of the technology in the production department Theoretical support.
- Retracted
- 1 December 2018
- Published by SAGE Publications in International Journal of Electrical Engineering & Education
- Vol. 57 (1) , 41-53
RETRACTED: Discharge characteristic and flow control experiment for pneumatic actuator of dielectric barrier discharge multistage plasma
Test and diagnosis of the characteristics of the air flow induced by the pneumatic actuation of the plasma are the important basis for the plasma flow control. In order to well understand the electrical characteristics of the pneumatic actuation of the plasma and the influence of the actuation voltage amplitude and the phase on the induced flow characteristics, the dielectric barrier discharge actuators symmetrically distributed were selected for the experimental research. The experiment result shows that the discharge form of the actuators symmetrically distributed is filamentary discharge, uniformly occurring around the high-voltage electrodes, and this is different from the discharge picture of the actuators asymmetrically distributed; when the voltage applied on the high-voltage electrode near to the actuators has the same amplitude and phase, the induced directional jet flow is vertical to the actuator surface, and the speed is at the order of meter per second; the change of the amplitude or phase of the voltage applied on the high-voltage electrode of the actuator can induce a jet flow towards the upper left or the upper right, but cannot effectively increase the induced airflow velocity.
- 1 December 2018
- Published by SAGE Publications in International Journal of Electrical Engineering & Education
- Vol. 57 (1) , 41-53
RetractedRETRACTED: Discharge characteristic and flow control experiment for pneumatic actuator of dielectric barrier discharge multistage plasma
Test and diagnosis of the characteristics of the air flow induced by the pneumatic actuation of the plasma are the important basis for the plasma flow control. In order to well understand the electrical characteristics of the pneumatic actuation of the plasma and the influence of the actuation voltage amplitude and the phase on the induced flow characteristics, the dielectric barrier discharge actuators symmetrically distributed were selected for the experimental research. The experiment result shows that the discharge form of the actuators symmetrically distributed is filamentary discharge, uniformly occurring around the high-voltage electrodes, and this is different from the discharge picture of the actuators asymmetrically distributed; when the voltage applied on the high-voltage electrode near to the actuators has the same amplitude and phase, the induced directional jet flow is vertical to the actuator surface, and the speed is at the order of meter per second; the change of the amplitude or phase of the voltage applied on the high-voltage electrode of the actuator can induce a jet flow towards the upper left or the upper right, but cannot effectively increase the induced airflow velocity.