TWTingting Wang

Tingting Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tingting Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Top Cited Papers
    Open Access

    Energy absorption and deformation of Re-entrant Bi-material tubular metamaterials

    by Yinchuan He, Hongyu Yang, Chi Zhang, Wenlong Liu, Li Wang, Tingting Wang, Guoxing Lu, Juntao Yu, Kwong Ming Tse


  • Open Access

    A New Filler for Epoxy Resin: Study on the Properties of Graphite Carbon Nitride (g-C3N4) Reinforced Epoxy Resin Composites

    by Tingting Wang, Bo Song, Li Wang

    In this study, graphitic carbon nitride (g-C3N4) as a novel filler was used for fabricating epoxy nanocomposites. The static mechanical, dynamic thermal-mechanical properties and thermostability of as-prepared g-C3N4/epoxy nanocomposites were significantly ameliorated compared with that of the pure epoxy matrix. The tensile modulus and flexural modulus of g-C3N4/epoxy nanocomposites increased by 31.81% and 28.28%, respectively. Meanwhile, the tensile and flexural strength was also improved by 16.02% and 12.67%, respectively. The g-C3N4/epoxy nanocomposites exhibited an increased storage modulus and glass transition temperature. The markedly improved mechanical and viscoelasticity properties were attributed to the stronger interfacial interaction caused by enlarged contact area and increased chemical bonding, and enhanced mechanical interlocking on the interface. The loss factor of epoxy nanocomposites also raised by 40% due to the comprehensive effect of frication caused by the relative slip between nanosheets, micro-constrained layer damping structure and the reversible cycle of breakage and re-established of the hydrogen bond. Meanwhile, the 10% weightlessness temperature (Tinitial), semi weightlessness temperature (Thalf) of g-C3N4/epoxy nanocomposites have increased by about 15 °C and 14 °C, respectively.


  • Open Access

    Effect of Dimensions and Agglomerations of Carbon Nanotubes on Synchronous Enhancement of Mechanical and Damping Properties of Epoxy Nanocomposites

    by Tingting Wang, Bo Song, Kun Qiao, Yudong Huang, Li Wang

    In order to achieve simultaneous enhancement of mechanical and damping properties, epoxy resin nanocomposites reinforced with a series of carboxylic multi-walled carbon nanotubes (C-MWCNTs) with different dimensions were prepared. A solution-based high-speed shear dispersion method was developed. The dispersion mechanism of carbon nanotubes was studied, and the degree of dispersion difficulty of carbon nanotubes with different dimensions was evaluated by theoretical calculation, and the minimum size of agglomerates for dispersion based on the mechanism of rupture was deduced. Then, the effect of synchronous enhancement on the mechanical and damping properties was tested by experiment. The effects of dimensions and agglomerations on the tensile properties, damping properties, and glass transition temperature (Tg) of the nanocomposites were investigated. The ranking of dispersion difficulty was verified using the deviations between predicted and experimental tensile modulus. The experimental results showed that the effects of synchronous enhancement on the mechanical properties and damping capacity of two kinds of specimens were remarkable and the only drawback was that their Tg showed the maximum decrease. Further studies indicated that C-MWCNTs with large aspect ratios and large specific surface areas possessed better effects on synchronous enhancement, but caused a decrease in the glass transition temperature, while agglomeration had the opposite effect. The results of this work would be helpful for preparing improved structural damping integrated composites.


  • Influence of the hybrid ratio and stacking sequence on mechanical and damping properties of hybrid composites

    by Tingting Wang, Bo Song, Kun Qiao, Chen Ding, Li Wang

    A study on the correlation between the performances and configurations of plain weave composites reinforced by T300 carbon and aramid fibers is presented in this paper. Laminations with various hybrid ratios and stacking sequences were fabricated by vacuum‐assisted resin transfer molding (VARTM), and then tensile, flexural, interlaminar shear, and damping properties were investigated. The results indicate that the tensile modulus of hybrid composites is determined only by hybrid ratio, while tensile strength is also affected by stacking sequence at an identical hybrid ratio. The concentration of carbon fibers in the center of these configurations leads to a greater tensile strength. For flexural properties, obvious classification characteristics are observed in the load–displacement curves, and both flexural modulus and strength are determined by the stacking sequence. While the flexural properties of all configurations are insensitive to the hybrid ratio, a structure of “Carbon/Aramid” in the outer layer is shown to be detrimental to flexural strength. The study on the damping property shows that both hybrid ratio and stacking sequence have a great influence on the loss factors of these composites. The effect of hybrid interface in energy consumption cannot be ignored, as the interlaminar shear strength test demonstrates that the interface between carbon and aramid layers is superior to that of pure aramid layers. POLYM. COMPOS., 40:2368–2380, 2019. © 2018 Society of Plastics Engineers