Céline Pascale
Research Subjects
Research Interests
Céline Pascale has a total of 128 co-authors. Here are the top co-authors by number of shared publications:
Andreas Ackermann
Department of Chemical and Biological Metrology, Federal Institute of Metrology (METAS), Bern-Wabern, 3003, Switzerland
14 shared publications- Maitane Iturrate-Garcia
Federal Institute of Metrology METAS
13 shared publications - Martin K. Vollmer
Laboratory for Air Pollution/Environmental Technology, Empa, Dübendorf, 8600, Switzerland
13 shared publications - Stefan Reimann
Swiss Federal Laboratories for Materials Science and Technology, Empa, 8600 Dübendorf, Switzerland
13 shared publications Bernhard Niederhauser
Chemical and biological reference, Federal Institute of Metrology (METAS), Lindenweg 50, 3003 Bern-Wabern, Switzerland
12 shared publicationsChristophe Sutour
Department of Gas Metrology, Laboratoire National de Métrologie et d'Essais (LNE), 75724 Paris, CEDEX 15, France
12 shared publications
Latest Publications
- Open Access
- 14 March 2026
- Published by Copernicus GmbH
Laboratory validation of a compact laser spectrometer for trace-level water vapor measurements
Accurate measurements of water vapor (H2O) in the upper troposphere-lower stratosphere (UTLS, ~8-25 km altitude) are still very challenging, due to the low abundance of H2O in this region (~5 ppm). The standard method for balloon-borne measurements of UTLS H2O in global monitoring networks (e.g., GRUAN, GCOS reference upper air network) is chilled-mirror hygrometry. However, this technique is currently undergoing a major reconception, with the introduction of Peltier-based instruments as well as alternative cooling agents to the phasing-out fluoroform (HFC-23). Therefore, alternative, high-accuracy methods for in-situ measurements of UTLS H2O are required.To this aim, we developed ALBATROSS, a lightweight (< 3.5 kg) laser absorption spectrometer for balloon-borne measurements of UTLS H2O [1]. ALBATROSS is based on a continuous-wave (cw) distributed feedback quantum cascade laser (DFB-QCL) emitting at 6.014 μm, and a monolithic segmented circular multipass cell with an optical path length of 6 m and a cell diameter of 10.8 cm. The multipass cell is highly resistant to thermal and mechanical stress, and can be operated either in a closed-path (laboratory) or an open-path (flight) configuration.The performance of the spectrometer at UTLS-relevant conditions was assessed by a series of laboratory-based validation experiements. These measurements require the generation of reference gases with H2O amount fractions in the low-ppm range (< 5 ppm), and their quantification at low pressures (< 100 mbar). At such conditions, artifacts due to the strong surface adsorption/desorption properties of H2O become critical. These "memory" effects must be minimized by a careful design of the gas handling system and of the experimental procedure. At the same time, to achieve the required accuracy of ~1-2 % (i.e., 50-100 ppb), high-order line shape models, beyond the standard Voigt profile, must be considered for the spectroscopic retrieval.In this presentation, we focus on the technical challenges and the results achieved in two distinct activities performed with ALBATROSS: an SI-traceable validation, using reference gases generated by a dynamic-gravimetric permeation method [2], and the AquaVIT-4 intercomparison of atmospheric hygrometers, held at the AIDA cloud simulation chamber in Karlsruhe, Germany [3]. Particularly, we highlight the best practices to address surface effects and other artifacts related to the gas handling system, as well as the importance of using an advanced line shape model (namely, the quadratic speed-dependent Voigt profile, qSDVP), and how to empirically obtain the necessary parameters not contained in the HITRAN database. This provides a general blueprint for the validation of a laser spectrometer dealing with a highly adsorbing gas at very low concentrations and pressures, such as H2O at UTLS-relevant conditions, in a laboratory setting.The instrument is currently deployed in a series of atmospheric test flights within the Swiss H2O-Hub GCOS-project. Overall, the results demonstrate the exceptional potential of mid-IR laser absorption spectroscopy as a new reference method for in situ measurements of UTLS H2O. [1] Graf et al., Atmos. Meas. Tech., 14, 1365–1378, 2021.[2] Brunamonti et al., Atmos. Meas. Tech., 16, 4391–4407, 2023.[3] Brunamonti et al., Atmos. Meas. Tech., 18, 5321–5348, 2025.
- 14 March 2026
- Published by Copernicus GmbH
Open AccessLaboratory validation of a compact laser spectrometer for trace-level water vapor measurements
Accurate measurements of water vapor (H2O) in the upper troposphere-lower stratosphere (UTLS, ~8-25 km altitude) are still very challenging, due to the low abundance of H2O in this region (~5 ppm). The standard method for balloon-borne measurements of UTLS H2O in global monitoring networks (e.g., GRUAN, GCOS reference upper air network) is chilled-mirror hygrometry. However, this technique is currently undergoing a major reconception, with the introduction of Peltier-based instruments as well as alternative cooling agents to the phasing-out fluoroform (HFC-23). Therefore, alternative, high-accuracy methods for in-situ measurements of UTLS H2O are required.To this aim, we developed ALBATROSS, a lightweight (< 3.5 kg) laser absorption spectrometer for balloon-borne measurements of UTLS H2O [1]. ALBATROSS is based on a continuous-wave (cw) distributed feedback quantum cascade laser (DFB-QCL) emitting at 6.014 μm, and a monolithic segmented circular multipass cell with an optical path length of 6 m and a cell diameter of 10.8 cm. The multipass cell is highly resistant to thermal and mechanical stress, and can be operated either in a closed-path (laboratory) or an open-path (flight) configuration.The performance of the spectrometer at UTLS-relevant conditions was assessed by a series of laboratory-based validation experiements. These measurements require the generation of reference gases with H2O amount fractions in the low-ppm range (< 5 ppm), and their quantification at low pressures (< 100 mbar). At such conditions, artifacts due to the strong surface adsorption/desorption properties of H2O become critical. These "memory" effects must be minimized by a careful design of the gas handling system and of the experimental procedure. At the same time, to achieve the required accuracy of ~1-2 % (i.e., 50-100 ppb), high-order line shape models, beyond the standard Voigt profile, must be considered for the spectroscopic retrieval.In this presentation, we focus on the technical challenges and the results achieved in two distinct activities performed with ALBATROSS: an SI-traceable validation, using reference gases generated by a dynamic-gravimetric permeation method [2], and the AquaVIT-4 intercomparison of atmospheric hygrometers, held at the AIDA cloud simulation chamber in Karlsruhe, Germany [3]. Particularly, we highlight the best practices to address surface effects and other artifacts related to the gas handling system, as well as the importance of using an advanced line shape model (namely, the quadratic speed-dependent Voigt profile, qSDVP), and how to empirically obtain the necessary parameters not contained in the HITRAN database. This provides a general blueprint for the validation of a laser spectrometer dealing with a highly adsorbing gas at very low concentrations and pressures, such as H2O at UTLS-relevant conditions, in a laboratory setting.The instrument is currently deployed in a series of atmospheric test flights within the Swiss H2O-Hub GCOS-project. Overall, the results demonstrate the exceptional potential of mid-IR laser absorption spectroscopy as a new reference method for in situ measurements of UTLS H2O. [1] Graf et al., Atmos. Meas. Tech., 14, 1365–1378, 2021.[2] Brunamonti et al., Atmos. Meas. Tech., 16, 4391–4407, 2023.[3] Brunamonti et al., Atmos. Meas. Tech., 18, 5321–5348, 2025.
- Open Access
- 24 January 2025
- Published by Copernicus GmbH in Atmospheric Measurement Techniques
- Vol. 18 (2) , 371-403
Towards a high-quality in situ observation network for oxygenated volatile organic compounds (OVOCs) in Europe: transferring metrological traceability to the field
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assessing the trends of these secondary air pollutants. Metrological traceability of the measurements to the International System of Units (SI traceability) contributes to both measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at an atmospheric amount of substance fraction levels (< 10 nmol mol−1). Here, we present the protocols developed to transfer SI traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole-air samples, were then assessed using a thermal desorber–gas chromatograph–flame ionisation detector (TD–GC–FID) and proton transfer reaction–time of flight–mass spectrometer (PTR–ToF–MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on the dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at an amount of substance fractions around 10 nmol mol−1. For the working standards based on certified spiked whole-air samples in pressurised cylinders, results showed a good agreement among the laboratories (i.e. differences within the measurement expanded uncertainty (U) ranging between 0.5 and 3.3 nmol mol−1) and with the certified amount of substance fraction for acetaldehyde (15.7 nmol mol−1 ± 3.6 (U) nmol mol−1), acetone (17 nmol mol−1 ± 1.5 (U) nmol mol−1) and MEK (12.3 nmol mol−1 ± 2.3 (U) nmol mol−1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole-air samples filled into pressurised cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among the metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e. RGMs and working standards). Besides this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI traceability to monitoring stations.
- 24 January 2025
- Published by Copernicus GmbH in Atmospheric Measurement Techniques
- Vol. 18 (2) , 371-403
Open AccessTowards a high-quality in situ observation network for oxygenated volatile organic compounds (OVOCs) in Europe: transferring metrological traceability to the field
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assessing the trends of these secondary air pollutants. Metrological traceability of the measurements to the International System of Units (SI traceability) contributes to both measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at an atmospheric amount of substance fraction levels (< 10 nmol mol−1). Here, we present the protocols developed to transfer SI traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole-air samples, were then assessed using a thermal desorber–gas chromatograph–flame ionisation detector (TD–GC–FID) and proton transfer reaction–time of flight–mass spectrometer (PTR–ToF–MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on the dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at an amount of substance fractions around 10 nmol mol−1. For the working standards based on certified spiked whole-air samples in pressurised cylinders, results showed a good agreement among the laboratories (i.e. differences within the measurement expanded uncertainty (U) ranging between 0.5 and 3.3 nmol mol−1) and with the certified amount of substance fraction for acetaldehyde (15.7 nmol mol−1 ± 3.6 (U) nmol mol−1), acetone (17 nmol mol−1 ± 1.5 (U) nmol mol−1) and MEK (12.3 nmol mol−1 ± 2.3 (U) nmol mol−1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole-air samples filled into pressurised cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among the metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e. RGMs and working standards). Besides this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI traceability to monitoring stations.
- Open Access
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Reply on RC1
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessReply on RC1
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Reply on CC1
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessReply on CC1
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Reply on RC2
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessReply on RC2
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Reply on RC3
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 5 November 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessReply on RC3
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 3 October 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Comment on egusphere-2024-2236 by Owen Cooper
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 3 October 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessComment on egusphere-2024-2236 by Owen Cooper
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 27 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Comment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 27 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessComment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 18 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Comment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 18 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessComment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- Open Access
- 4 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Comment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.
- 4 September 2024
- Published by Copernicus GmbH
- Vol. 2024, 1-45
Open AccessComment on egusphere-2024-2236
Volatile organic compounds (VOCs) have a large impact on the oxidising capacity of the troposphere and are major precursors of tropospheric ozone and secondary atmospheric aerosols. Accurate measurements and data comparability of VOCs among monitoring networks are essential to assess the trends of these secondary air pollutants. Metrological traceability of the measurements to the international system of units (SI-traceability) contributes to both: measurement consistency and data comparability. Accurate, stable and SI-traceable reference gas mixtures (RGMs) and working standards are needed to achieve SI-traceability through an unbroken chain of calibrations of the analytical instruments used to monitor VOCs. However, for many oxygenated VOCs (OVOCs), such RGMs and working standards are not available at atmospheric amount of substance fraction levels (< 10 nmol mol-1). Here, we present the protocols developed to transfer SI-traceability to the field by producing two types of SI-traceable working standards for selected OVOCs. These working standards, based on RGMs diluted dynamically with dry nitrogen and on certified spiked whole air samples, were then assessed using Thermal Desorption-Gas Chromatography-Flame Ionization Detector (TD-GC-FID) and Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) as analytical methods. For that purpose, we calibrated five analytical instruments using in-house calibration standards and treated the new SI-traceable working standards as samples. Due to analytical limitations, the assessment was only possible for acetaldehyde, acetone, methanol and methyl ethyl ketone (MEK). Relative differences between assigned and measured values were used to assess the working standards based on dilution of RGMs. The relative differences were within the measurement uncertainty for acetone, MEK, methanol and acetaldehyde at amount of substance fractions around 10 nmol mol-1. For the working standards based on certified spiked whole air samples in pressurized cylinders, results showed a good agreement among the laboratories (i.e., differences within the measurement expanded uncertainties (U) ranging between 0.5 nmol mol-1 and 3.3 nmol mol-1) and with the certified amount of substance fraction value for acetaldehyde (15.7 nmol mol-1 ± 3.6 (U) nmol mol-1), acetone (17 nmol mol-1 ± 1.5 (U) nmol mol-1) and MEK (12.3 nmol mol-1 ± 2.3 (U) nmol mol-1). Despite the promising results for the working standards based on the dilution of RGMs and on certified spiked whole air samples filled into pressurized cylinders, the assessment must be considered with care due to the large measurement uncertainty, particularly for methanol. Active collaboration among metrological, meteorological and atmospheric chemistry monitoring communities is needed to tackle the challenges of OVOC monitoring, such as the lack of stable and SI-traceable calibration standards (i.e., RGMs and working standards). Besides from this collaboration, other research applications, such as modelling and remote sensing, may benefit from the transfer of SI-traceability to monitoring stations.