Tianqi Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tianqi Zhang has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Tianbiao Yu
School of Mechanical Engineering and Automation, Northeastern University, Shenyang, People’s Republic of China
5 shared publications Jinzhong Wu
School of Intelligent Engineering, Shaoxing University, Shaoxing, PR China
4 shared publicationsTianbiao Yu
4 shared publicationsYan Zhang
4 shared publicationsJi Zhao
3 shared publicationsLihui Zhang
School of Intelligent Engineering, Shaoxing University, Shaoxing, PR China
3 shared publications
Latest Publications
- Open Access
- 11 August 2026
- Published by Elsevier in Materials Today Communications
- Vol. 55
Surface roughness prediction of zirconia ceramic polishing based on adaptive weighted ensemble neural network model
- 11 August 2026
- Published by Elsevier in Materials Today Communications
- Vol. 55
Open AccessSurface roughness prediction of zirconia ceramic polishing based on adaptive weighted ensemble neural network model
- 30 July 2026
- Published by Springer Nature in JOM
- Vol. 78 (10) , 9473-9489
Enhanced Mechanical and Corrosion Properties of As-Extruded Mg-Sm-Zn Alloy Bars via Mn Addition: Microstructure Evolution and VPSC Simulations
- 30 July 2026
- Published by Springer Nature in JOM
- Vol. 78 (10) , 9473-9489
Enhanced Mechanical and Corrosion Properties of As-Extruded Mg-Sm-Zn Alloy Bars via Mn Addition: Microstructure Evolution and VPSC Simulations
- 24 May 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (14)
Carbon Content Optimization and Performance Characterization of High Entropy Carbonitride Ceramics
This study systematically investigates the effects of excess carbon content (0, 5, 10, 15 at%) on the phase composition, microstructure, and mechanical properties of (Hf, Ti, V,W, Zr)(C,N) high entropy carbonitride ceramics fabricated through combined carbothermal reduction nitridation and SPS under identical processing conditions. Microstructural characterization reveals that four high entropy carbonitride powders contain high entropy phases along with WC, residual carbon, and oxide solid solution phases. After sintering at 2000°C, the ceramics primarily consist of high entropy matrix phases and oxide solid solutions phases, while the HECN‐15C sample additionally retains residual carbon. The ceramics exhibit relative densities of 99.2% ± 0.7%, 98.27% ± 0.6%, 97.09% ± 0.2%, and 93.71% ± 0.3%. Mechanical testing demonstrates hardness values ranging from 22.13% ± 1.02% to 25.29 ± 1.79 GPa and fracture toughness between 3.66 ± 0.38 and 4.28 ± 0.24 MPa m 1/2 across the series. Optimal performance is achieved at 10 at% excess carbon content, which exhibits highest hardness (25.29 ± 1.79 GPa) and toughness (4.28 ± 0.24 MPa m 1/2 ). However, further increasing carbon to 15 at% degrades mechanical properties (22.13 ± 1.02 GPa hardness), (3.66 ± 0.38 MPa m 1/2 toughness). Precise control of carbon content in raw materials is very important, this work plays an important guiding role for the further development of high entropy carbonitride ceramic.
- 24 May 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (14)
Carbon Content Optimization and Performance Characterization of High Entropy Carbonitride Ceramics
This study systematically investigates the effects of excess carbon content (0, 5, 10, 15 at%) on the phase composition, microstructure, and mechanical properties of (Hf, Ti, V,W, Zr)(C,N) high entropy carbonitride ceramics fabricated through combined carbothermal reduction nitridation and SPS under identical processing conditions. Microstructural characterization reveals that four high entropy carbonitride powders contain high entropy phases along with WC, residual carbon, and oxide solid solution phases. After sintering at 2000°C, the ceramics primarily consist of high entropy matrix phases and oxide solid solutions phases, while the HECN‐15C sample additionally retains residual carbon. The ceramics exhibit relative densities of 99.2% ± 0.7%, 98.27% ± 0.6%, 97.09% ± 0.2%, and 93.71% ± 0.3%. Mechanical testing demonstrates hardness values ranging from 22.13% ± 1.02% to 25.29 ± 1.79 GPa and fracture toughness between 3.66 ± 0.38 and 4.28 ± 0.24 MPa m 1/2 across the series. Optimal performance is achieved at 10 at% excess carbon content, which exhibits highest hardness (25.29 ± 1.79 GPa) and toughness (4.28 ± 0.24 MPa m 1/2 ). However, further increasing carbon to 15 at% degrades mechanical properties (22.13 ± 1.02 GPa hardness), (3.66 ± 0.38 MPa m 1/2 toughness). Precise control of carbon content in raw materials is very important, this work plays an important guiding role for the further development of high entropy carbonitride ceramic.
- 7 February 2026
- Published by Elsevier in Tribology International
- Vol. 219
Multi-scale analysis and modeling of material removal process for ultrasonic vibration-assisted polishing
- 7 February 2026
- Published by Elsevier in Tribology International
- Vol. 219
Multi-scale analysis and modeling of material removal process for ultrasonic vibration-assisted polishing
- 25 April 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (14) , 23654-23668
Surface profile prediction modeling of spiral toolpath for axial ultrasonic vibration-assisted polishing
- 25 April 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (14) , 23654-23668
Surface profile prediction modeling of spiral toolpath for axial ultrasonic vibration-assisted polishing
- 1 April 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 153-154, 131-142
Grinding temperature field prediction by meshless finite block method with double infinite element
- 1 April 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 153-154, 131-142
Grinding temperature field prediction by meshless finite block method with double infinite element
- 1 April 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 266, 715-725
CFD simulation and experimental studies of suspension flow field in ultrasonic polishing
- 1 April 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 266, 715-725
CFD simulation and experimental studies of suspension flow field in ultrasonic polishing