Arne F. Jacob
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Arne F. Jacob has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Philip Birtel
Thales Deutschland GmbH, Electron Devices, Ulm, Germany
4 shared publications - Aleksandar Savic
Institute of High-Frequency Technology, Hamburg University of Technology, Hamburg, Germany
3 shared publications - Anton Sieganschin
Institute of High-Frequency Technology, Hamburg University of Technology, Hamburg, Germany
3 shared publications - Frauke Kathinka Helene Gellersen
Physikalisch-Technische Bundesanstalt (PTB), Brunswick, Germany
3 shared publications - Moritz Hagermann
Institute of High-Frequency Technology, Hamburg University of Technology, Hamburg, Germany
3 shared publications - Thomas Jaschke
Institute of High-Frequency Technology, Hamburg University of Technology, Hamburg, Germany
3 shared publications
Latest Publications
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 6130-6139
A Hybrid-Integrated K-/Ka-Band Phased Array Module With Dual-Polarized Shared Aperture
In this work, a passive dual-polarized shared antenna aperture and active beamformer front-ends are integrated into a phased array module. The system operates in the $K$ -/ $Ka$ -band and is intended for satellite communications. It consists of a hybrid assembly of aluminum waveguide components and printed circuit boards that are electrically connected by anisotropic conductive adhesive, containing a heterodyne transceiver with $L$ -band interfaces. For proof of concept, a demonstrator with 64 transmit (Tx) and 32 receive (Rx) elements is fabricated and characterized. It provides full-duplex Tx/Rx operation with bandwidths of 1 GHz centered around 29.5 (Tx) and 19.5 GHz (Rx), beam scanning over wide angular ranges up to 60 $^{\circ}$ in both $H$ -and $E$ -planes, an equivalent isotropic radiated power of up to 20.4 dBW at 1-dB power compression and an Rx gain to noise temperature ratio of up to $-$ 10.2 dB/K at room temperature. The measured performances are comparable to those of phased array systems with separate apertures and thus validate the integration approach.
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 6130-6139
A Hybrid-Integrated K-/Ka-Band Phased Array Module With Dual-Polarized Shared Aperture
In this work, a passive dual-polarized shared antenna aperture and active beamformer front-ends are integrated into a phased array module. The system operates in the $K$ -/ $Ka$ -band and is intended for satellite communications. It consists of a hybrid assembly of aluminum waveguide components and printed circuit boards that are electrically connected by anisotropic conductive adhesive, containing a heterodyne transceiver with $L$ -band interfaces. For proof of concept, a demonstrator with 64 transmit (Tx) and 32 receive (Rx) elements is fabricated and characterized. It provides full-duplex Tx/Rx operation with bandwidths of 1 GHz centered around 29.5 (Tx) and 19.5 GHz (Rx), beam scanning over wide angular ranges up to 60 $^{\circ}$ in both $H$ -and $E$ -planes, an equivalent isotropic radiated power of up to 20.4 dBW at 1-dB power compression and an Rx gain to noise temperature ratio of up to $-$ 10.2 dB/K at room temperature. The measured performances are comparable to those of phased array systems with separate apertures and thus validate the integration approach.
- 4 May 2024
- Published by Elsevier in Materials Research Bulletin
- Vol. 178
Hexagonal ferrites for self-biasing circulators integrated in LTCC microwave modules
- 4 May 2024
- Published by Elsevier in Materials Research Bulletin
- Vol. 178
Hexagonal ferrites for self-biasing circulators integrated in LTCC microwave modules
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (6) , 111-112
A Microwave Rock Has Gone [In Memoriam]
Recounts the career and contributions of Reinhard Knochel.
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (6) , 111-112
A Microwave Rock Has Gone [In Memoriam]
Recounts the career and contributions of Reinhard Knochel.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Electromagnetics, RF and Microwaves in Medicine and Biology
- Vol. 7 (3) , 236-244
CHO and HepG2 Single-Cell Characterization With Planar Microchip Sensors up to 40 GHz
The article deals with broadband microwave measurements performed on single dead and living biological cells from CHO and HepG2 cell lines. It reports results obtained with coplanar waveguide reflection and transmission type sensors, respectively. A straight-forward single liquid calibration procedure allows to extract the complex cell permittivity and compare it to that of the surrounding medium. The contrast is analyzed through $p$ -value tests and in terms of the usual Cole-Cole parameters. The results demonstrate the distinguishability of the cell lines based on the permittivity.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Electromagnetics, RF and Microwaves in Medicine and Biology
- Vol. 7 (3) , 236-244
CHO and HepG2 Single-Cell Characterization With Planar Microchip Sensors up to 40 GHz
The article deals with broadband microwave measurements performed on single dead and living biological cells from CHO and HepG2 cell lines. It reports results obtained with coplanar waveguide reflection and transmission type sensors, respectively. A straight-forward single liquid calibration procedure allows to extract the complex cell permittivity and compare it to that of the surrounding medium. The contrast is analyzed through $p$ -value tests and in terms of the usual Cole-Cole parameters. The results demonstrate the distinguishability of the cell lines based on the permittivity.
- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (3) , 2443-2453
A Dual-Polarized SIW Lens Antenna Array for Rx-/Tx-Integration at K/Ka-Band
The terminal antenna with dual circular polarization reported here operates around 20GHz and 30GHz, i.e., in the down- and uplink frequency bands of current satellite communication systems. The passive array, this work focuses on, integrates the receive and the transmit paths (Rx/Tx) in a single aperture. This approach is shown to be advantageous compared to classical solutions with two separate antennas. The modules, the array consists of, are formed by a stack of eight linear sub-arrays which themselves are composed of an alternating series of four Tx-only and four combined Rx/Tx end-fire antenna elements. The resulting brick architecture provides enough real estate for the future implementation of phased array electronics. The array is implemented in substrate integrated waveguide (SIW) technology. For improved matching, it is covered with a periodically shaped dielectric lens. A technique is proposed to mitigate cross-polarization in the pointing direction. A module is realized using standard technologies. The relevant array parameters are measured. The module patterns are synthesized from the individual element responses. They confirm the simulated results and, in particular, a bandwidth of more than 2.5GHz for both Rx and Tx.
- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (3) , 2443-2453
A Dual-Polarized SIW Lens Antenna Array for Rx-/Tx-Integration at K/Ka-Band
The terminal antenna with dual circular polarization reported here operates around 20GHz and 30GHz, i.e., in the down- and uplink frequency bands of current satellite communication systems. The passive array, this work focuses on, integrates the receive and the transmit paths (Rx/Tx) in a single aperture. This approach is shown to be advantageous compared to classical solutions with two separate antennas. The modules, the array consists of, are formed by a stack of eight linear sub-arrays which themselves are composed of an alternating series of four Tx-only and four combined Rx/Tx end-fire antenna elements. The resulting brick architecture provides enough real estate for the future implementation of phased array electronics. The array is implemented in substrate integrated waveguide (SIW) technology. For improved matching, it is covered with a periodically shaped dielectric lens. A technique is proposed to mitigate cross-polarization in the pointing direction. A module is realized using standard technologies. The relevant array parameters are measured. The module patterns are synthesized from the individual element responses. They confirm the simulated results and, in particular, a bandwidth of more than 2.5GHz for both Rx and Tx.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (2) , 471-479
A Transmission Line Approach for Rough Conductor Surface Impedance Analysis
This work proposes a transmission line approach to determine the surface impedance of conductors with rough surfaces. Based on the gradient model, the roughness is represented by a gradual transition of the intrinsic impedance. Discretization and successive impedance transformations then directly yield the surface impedance. Evaluating the fields is not necessary to this end, but still feasible if required. Investigations of the proposed model confirm the field diffusion to be fully characterized by a single dimensionless ratio, which enables a comprehensive analysis of the surface impedance regarding its dependency on frequency, conductivity, and roughness.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (2) , 471-479
A Transmission Line Approach for Rough Conductor Surface Impedance Analysis
This work proposes a transmission line approach to determine the surface impedance of conductors with rough surfaces. Based on the gradient model, the roughness is represented by a gradual transition of the intrinsic impedance. Discretization and successive impedance transformations then directly yield the surface impedance. Evaluating the fields is not necessary to this end, but still feasible if required. Investigations of the proposed model confirm the field diffusion to be fully characterized by a single dimensionless ratio, which enables a comprehensive analysis of the surface impedance regarding its dependency on frequency, conductivity, and roughness.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-7
Phase Noise Measurements for L-Band Applications at Attosecond Resolution
This article summarizes theoretical and technical limitations when applying carrier-suppression interferometer (CSI) methods for precision phase-noise measurements at attosecond resolution. The CSI setup reported here outperforms conventional down-mixing methods by more than two orders of magnitude. For phase noise measurements at 1.3 GHz operation frequency, a detection floor of $\mathscr {L}={-205}\,\,{\text {dBc/Hz}}$ and an excellent time resolution of 10.76 as within an offset frequency range from 40 Hz to 1 MHz have been achieved without the usage of cross correlation or power recycling techniques. Measurement setup resolution limits, calibration methods, and effects of transmission line group delays are reported. Phase shifters and attenuators in the CSI were identified as key components. Different phase shifter technologies based on passive switches, varactor diodes, and capacitors were investigated. The presented research can be used in future in combination with conventional receiver techniques and enhances the state of the art of phase noise measurements to attosecond resolution and above.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-7
Phase Noise Measurements for L-Band Applications at Attosecond Resolution
This article summarizes theoretical and technical limitations when applying carrier-suppression interferometer (CSI) methods for precision phase-noise measurements at attosecond resolution. The CSI setup reported here outperforms conventional down-mixing methods by more than two orders of magnitude. For phase noise measurements at 1.3 GHz operation frequency, a detection floor of $\mathscr {L}={-205}\,\,{\text {dBc/Hz}}$ and an excellent time resolution of 10.76 as within an offset frequency range from 40 Hz to 1 MHz have been achieved without the usage of cross correlation or power recycling techniques. Measurement setup resolution limits, calibration methods, and effects of transmission line group delays are reported. Phase shifters and attenuators in the CSI were identified as key components. Different phase shifter technologies based on passive switches, varactor diodes, and capacitors were investigated. The presented research can be used in future in combination with conventional receiver techniques and enhances the state of the art of phase noise measurements to attosecond resolution and above.
- 22 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (12) , 6492-6497
Drive-Induced Backward-Wave Oscillations in Helix Traveling-Wave Tubes—A Case Study
The output section of helix traveling-wave tubes (TWTs) usually features a tapered delay line to enhance the amplifier performance. This alters the phase velocity of the circuit waves, which, in particular, disturbs the narrowband synchronism between the backward wave (BW) and the electron beam. As a result, the excitation threshold of BW oscillations (BWOs) increases. Large-signal operation significantly alters beam-wave synchronism, as the electrons loose kinetic energy during the amplification process, i.e., toward the TWT output. As a result, beam and BW may interact over a larger distance, thus lowering the threshold for the onset of BWOs. These would thus be drive-induced in contrast to the zero-drive BWOs mentioned above. The following investigates the occurrence of such drive-induced BWOs as a case study of several different TWT models and proposes a theory for the large-signal instability. As the simulation process is quite involved and time-consuming, a heuristic approach for the fast prediction of the oscillation is presented as well.
- 22 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (12) , 6492-6497
Drive-Induced Backward-Wave Oscillations in Helix Traveling-Wave Tubes—A Case Study
The output section of helix traveling-wave tubes (TWTs) usually features a tapered delay line to enhance the amplifier performance. This alters the phase velocity of the circuit waves, which, in particular, disturbs the narrowband synchronism between the backward wave (BW) and the electron beam. As a result, the excitation threshold of BW oscillations (BWOs) increases. Large-signal operation significantly alters beam-wave synchronism, as the electrons loose kinetic energy during the amplification process, i.e., toward the TWT output. As a result, beam and BW may interact over a larger distance, thus lowering the threshold for the onset of BWOs. These would thus be drive-induced in contrast to the zero-drive BWOs mentioned above. The following investigates the occurrence of such drive-induced BWOs as a case study of several different TWT models and proposes a theory for the large-signal instability. As the simulation process is quite involved and time-consuming, a heuristic approach for the fast prediction of the oscillation is presented as well.
- 11 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Electromagnetics, RF and Microwaves in Medicine and Biology
- Vol. 6 (2) , 232-238
A Capacitive Microwave Sensor With Guard Electrode for Single-Cell Characterization
A capacitive microwave sensor with homogeneous field distribution is presented. It relies on a high-impedance parallel-plate arrangement and a properly positioned guard electrode to mitigate fringing field effects. The distance between the capacitor plates can be as large as their diameter. Such an arrangement allows permittivity measurements of irregularly shaped objects like individual biological cells. This is demonstrated with a microchip sensor in a microfluidic setup. The calibration requires only a single reference fluid.
- 11 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Electromagnetics, RF and Microwaves in Medicine and Biology
- Vol. 6 (2) , 232-238
A Capacitive Microwave Sensor With Guard Electrode for Single-Cell Characterization
A capacitive microwave sensor with homogeneous field distribution is presented. It relies on a high-impedance parallel-plate arrangement and a properly positioned guard electrode to mitigate fringing field effects. The distance between the capacitor plates can be as large as their diameter. Such an arrangement allows permittivity measurements of irregularly shaped objects like individual biological cells. This is demonstrated with a microchip sensor in a microfluidic setup. The calibration requires only a single reference fluid.
- 9 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (6) , 642-645
A Compact K-/Ka-Band Rectangular-to-Coplanar Waveguide Transition With Integrated Diplexer
This contribution presents a vertical transition between a WR34 rectangular waveguide (RWG) and two grounded coplanar waveguides (GCPW). It is intended for dual-band phased array applications and thus includes a diplexer. The RWG is the common port and the GCPWs are the diplexed 20 and 30 GHz ports. This yields a very compact design compared to conventional cascaded circuit topologies. The realized component exhibits a port matching and an isolation exceeding 10 dB and 30 dB, respectively, over more than 500 MHz in both bands.
- 9 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (6) , 642-645
A Compact K-/Ka-Band Rectangular-to-Coplanar Waveguide Transition With Integrated Diplexer
This contribution presents a vertical transition between a WR34 rectangular waveguide (RWG) and two grounded coplanar waveguides (GCPW). It is intended for dual-band phased array applications and thus includes a diplexer. The RWG is the common port and the GCPWs are the diplexed 20 and 30 GHz ports. This yields a very compact design compared to conventional cascaded circuit topologies. The realized component exhibits a port matching and an isolation exceeding 10 dB and 30 dB, respectively, over more than 500 MHz in both bands.