Binbin Qian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Binbin Qian has a total of 114 co-authors. Here are the top co-authors by number of shared publications:
- Lian Zhang
Monash University
6 shared publications Zhenghao Fei
Yancheng Teachers University
6 shared publicationsZongtang Liu
Yancheng Teachers University
6 shared publicationsLian Zhang
Department of Chemical and Biological Engineering Monash University Wellington Road Clayton 3800 Victoria Australia
5 shared publicationsSasha Yang
Department of Chemical and Biological Engineering Monash University Wellington Road Clayton 3800 Victoria Australia
5 shared publications- Huanting Wang
Department of Chemical and Biological Engineering Monash University Clayton Victoria Australia
4 shared publications
Latest Publications
- 16 November 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
Regioisomer-Controlled Biobased Benzoxazine Resin: Low-Temperature Curing, High Performance, and Intrinsic Flame Retardancy
The development of high-performance thermosetting resins that simultaneously combine low-temperature processability, thermal stability, flame retardancy, and favorable dielectric properties remains challenging. In this work, a biobased benzoxazine monomer, UA-Fa, was synthesized from Urolithin A and furfurylamine through a solvent-free strategy. The molecular structure of UA-Fa was systematically elucidated by spectroscopic characterization, including 1H-1H NOESY NMR analysis. Owing to its unique molecular architecture and multiple reactive sites, UA-Fa exhibited a low curing peak temperature of 203 °C, enabling low-temperature fabrication of the corresponding thermoset poly(UA-Fa). The cured resin exhibited a high glass transition temperature of 303 °C, together with excellent mechanical properties, including a tensile strength of 91.4 ± 4.7 MPa, a Young's modulus of 6.57 ± 0.27 GPa, and a hardness of 0.62 ± 0.02 GPa. Compared with the commercial resin poly(DBA-Pa), poly(UA-Fa) exhibited substantially improved thermal stability and flame retardancy, with its initial decomposition temperature and char yield reaching 404 °C and 73%, respectively, compared with 330 °C and 38% for poly(DBA-Pa). Moreover, the peak heat release rate and total heat release of poly(UA-Fa) were only 39.2 W/g and 4.3 kJ/g, corresponding to reductions of approximately 76 and 80%, respectively, relative to poly(DBA-Pa). In addition, poly(UA-Fa) exhibited a low dielectric constant of 2.77–2.51 over 100 Hz–2 MHz and maintained a dielectric constant below 3 from room temperature to 300 °C at 1 GHz. These results demonstrate that rational incorporation of a rigid biobased aromatic framework and multiple reactive sites provides an effective strategy for achieving the synergistic combination of low-temperature curing, thermal stability, flame retardancy, mechanical robustness, and low dielectric properties in benzoxazine thermosets.
- 16 November 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
Regioisomer-Controlled Biobased Benzoxazine Resin: Low-Temperature Curing, High Performance, and Intrinsic Flame Retardancy
The development of high-performance thermosetting resins that simultaneously combine low-temperature processability, thermal stability, flame retardancy, and favorable dielectric properties remains challenging. In this work, a biobased benzoxazine monomer, UA-Fa, was synthesized from Urolithin A and furfurylamine through a solvent-free strategy. The molecular structure of UA-Fa was systematically elucidated by spectroscopic characterization, including 1H-1H NOESY NMR analysis. Owing to its unique molecular architecture and multiple reactive sites, UA-Fa exhibited a low curing peak temperature of 203 °C, enabling low-temperature fabrication of the corresponding thermoset poly(UA-Fa). The cured resin exhibited a high glass transition temperature of 303 °C, together with excellent mechanical properties, including a tensile strength of 91.4 ± 4.7 MPa, a Young's modulus of 6.57 ± 0.27 GPa, and a hardness of 0.62 ± 0.02 GPa. Compared with the commercial resin poly(DBA-Pa), poly(UA-Fa) exhibited substantially improved thermal stability and flame retardancy, with its initial decomposition temperature and char yield reaching 404 °C and 73%, respectively, compared with 330 °C and 38% for poly(DBA-Pa). Moreover, the peak heat release rate and total heat release of poly(UA-Fa) were only 39.2 W/g and 4.3 kJ/g, corresponding to reductions of approximately 76 and 80%, respectively, relative to poly(DBA-Pa). In addition, poly(UA-Fa) exhibited a low dielectric constant of 2.77–2.51 over 100 Hz–2 MHz and maintained a dielectric constant below 3 from room temperature to 300 °C at 1 GHz. These results demonstrate that rational incorporation of a rigid biobased aromatic framework and multiple reactive sites provides an effective strategy for achieving the synergistic combination of low-temperature curing, thermal stability, flame retardancy, mechanical robustness, and low dielectric properties in benzoxazine thermosets.
- Open Access
- 27 March 2026
- Published by Elsevier in SSRN Electronic Journal
Multiscale Occurrence and Recovery Behavior of Rare Earth Elements in Hazardous Tungsten Leaching Slag
Tungsten leaching slag is a hazardous industrial by-product generated during tungsten extraction and represents a potential anthropogenic resource for rare earth elements (REEs). In this study, the occurrence, mobilization, and leaching behavior of REEs in tungsten leaching slag were systematically investigated through an integrated multiscale approach combining sequential chemical extraction, micro- to nanoscale characterization, density functional theory (DFT) calculations, and acid leaching experiments. The slag contains a high total REE content (3,861.2 mg/kg), with heavy rare earth elements (HREEs) accounting for ~65% of the total inventory, indicating an unusual HREE-enriched secondary resource. Sequential extraction and microstructural analyses show that REEs are predominantly hosted by Fe–Mn oxides and aluminosilicate matrices, with Fe–Mn oxides occurring as fine particles associated with aluminosilicate surfaces. DFT calculations indicate that lattice incorporation of REEs into Fe–Mn oxides is thermodynamically favored over ideal surface adsorption. HCl leaching has been demonstrated to be an effective method for REE recovery, achieving an overall recovery of 98% under optimized conditions. Despite HREE dominance in bulk composition, light rare earth elements (LREEs) exhibit higher leaching efficiencies due to differences in host-phase reactivity. The results indicate that proton-promoted dissolution of Fe–Mn oxide host phases governs the rapid initial release of REEs, whereas aluminosilicate matrices constrain the mobilization of structurally bound REEs. These findings provide mechanistic insights into REEs occurrence and recovery from tungsten metallurgical wastes and support the development of targeted strategies for the valorization of hazardous tungsten slag.
- 27 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMultiscale Occurrence and Recovery Behavior of Rare Earth Elements in Hazardous Tungsten Leaching Slag
Tungsten leaching slag is a hazardous industrial by-product generated during tungsten extraction and represents a potential anthropogenic resource for rare earth elements (REEs). In this study, the occurrence, mobilization, and leaching behavior of REEs in tungsten leaching slag were systematically investigated through an integrated multiscale approach combining sequential chemical extraction, micro- to nanoscale characterization, density functional theory (DFT) calculations, and acid leaching experiments. The slag contains a high total REE content (3,861.2 mg/kg), with heavy rare earth elements (HREEs) accounting for ~65% of the total inventory, indicating an unusual HREE-enriched secondary resource. Sequential extraction and microstructural analyses show that REEs are predominantly hosted by Fe–Mn oxides and aluminosilicate matrices, with Fe–Mn oxides occurring as fine particles associated with aluminosilicate surfaces. DFT calculations indicate that lattice incorporation of REEs into Fe–Mn oxides is thermodynamically favored over ideal surface adsorption. HCl leaching has been demonstrated to be an effective method for REE recovery, achieving an overall recovery of 98% under optimized conditions. Despite HREE dominance in bulk composition, light rare earth elements (LREEs) exhibit higher leaching efficiencies due to differences in host-phase reactivity. The results indicate that proton-promoted dissolution of Fe–Mn oxide host phases governs the rapid initial release of REEs, whereas aluminosilicate matrices constrain the mobilization of structurally bound REEs. These findings provide mechanistic insights into REEs occurrence and recovery from tungsten metallurgical wastes and support the development of targeted strategies for the valorization of hazardous tungsten slag.
- Open Access
- 2 September 2025
- Published by Wiley in Small Structures
- Vol. 6 (11)
Facile Synthesis of Magnetite‐Rich Core‐Shell Catalysts with Tunable Nanostructure and Atomic Composition from Solid Waste for Superior Water–Gas Shift Reaction
Nanostructured catalysts show superior performance in terms of reaction selectivity and efficiency compared to the bulk catalysts. However, the former are normally synthesized by high‐purity chemicals of high cost, which compromises their advantages from the whole process analysis. In contrast, solid waste containing the desirable metal elements is a promising precursor to synthesize the corresponding nanostructured catalysts with comparable or even improved catalytic performance with the increased catalytic sites available via the deliberate atom doping from the co‐existing impurity cations. Herein, the core‐shell nanostructured magnetite particles are successfully prepared from red mud, a massive solid waste generated from the alumina industry, and the shell thickness, elemental composition, and porosity can be controlled simultaneously by adjusting the pH values of the precipitation. At the optimized pH value of 6, the obtained core‐shell nanostructured particles exhibit outstanding catalysts for high‐temperature water‐gas shift reaction with high reaction efficiency comparable to the literature. The work demonstrates that refining valuable metal sources from wastes is a cost‐effective alternative to prepare nanostructured catalysts of high value, which can benefit upcycling of solid waste for sustainable industry and environmental protection.
- 2 September 2025
- Published by Wiley in Small Structures
- Vol. 6 (11)
Open AccessFacile Synthesis of Magnetite‐Rich Core‐Shell Catalysts with Tunable Nanostructure and Atomic Composition from Solid Waste for Superior Water–Gas Shift Reaction
Nanostructured catalysts show superior performance in terms of reaction selectivity and efficiency compared to the bulk catalysts. However, the former are normally synthesized by high‐purity chemicals of high cost, which compromises their advantages from the whole process analysis. In contrast, solid waste containing the desirable metal elements is a promising precursor to synthesize the corresponding nanostructured catalysts with comparable or even improved catalytic performance with the increased catalytic sites available via the deliberate atom doping from the co‐existing impurity cations. Herein, the core‐shell nanostructured magnetite particles are successfully prepared from red mud, a massive solid waste generated from the alumina industry, and the shell thickness, elemental composition, and porosity can be controlled simultaneously by adjusting the pH values of the precipitation. At the optimized pH value of 6, the obtained core‐shell nanostructured particles exhibit outstanding catalysts for high‐temperature water‐gas shift reaction with high reaction efficiency comparable to the literature. The work demonstrates that refining valuable metal sources from wastes is a cost‐effective alternative to prepare nanostructured catalysts of high value, which can benefit upcycling of solid waste for sustainable industry and environmental protection.
- Open Access
- 19 November 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 502
Facile synthesis of layered spinel ferrite from fly ash waste as a stable and active ketonisation catalyst
- 19 November 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 502
Open AccessFacile synthesis of layered spinel ferrite from fly ash waste as a stable and active ketonisation catalyst
- 29 April 2024
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 14 (10) , 7402-7415
Volcano-Shaped Correlation Dictated Superior Activity for Ultralow Al-Doped Iron Oxide toward High-Temperature Water–Gas Shift Reaction
- 29 April 2024
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 14 (10) , 7402-7415
Volcano-Shaped Correlation Dictated Superior Activity for Ultralow Al-Doped Iron Oxide toward High-Temperature Water–Gas Shift Reaction
- 11 December 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (51) , 19008-19015
Discontinuous Dissolution Mechanism of Olivine Deduced from a Topography Observation Method
Olivine dissolution plays an important role in environmental science and technology, from controlling global element circulation to carbon capture for climate change mitigation. Most studies have been focused on investigating its dissolution rates by monitoring chemical effluent changes under various conditions. However, only by observation of surface reactivity can we unravel the actual mechanism (s) of dissolution. Here, we studied the dissolution of an olivine (010) plane in a flow-through reaction cell with an acidic solution, a surface-controlled regime, and far-from-equilibrium conditions. Direct mineral surface topography measurements using vertical scanning interferometry and atomic force microscopy allowed for quantitative analyses of the spatial and temporal changes in the dissolution rate. The (010) plane dissolved discontinuously in time for different surface sites, resulting in a heterogeneously distributed rate map. Pits with different depths showed opposite dissolution rate distributions from the dislocation center to further out from the etch pit. Based on the step-wave model, we propose a mechanism of dissolution that is governed by the competition between Gibbs free energy of the dissolution process, Delta G, and the critical free energy of the opening of etch pits, i.e., Delta G(crit). The migration of step waves, the distribution of surface defects, the strain field of etch pits, and other dynamic elements, resulting in the instantaneous change of Delta G(crit) on the surface, are important factors leading to the discontinuous dissolution of crystal materials. This discontinuous dissolution provides new insight into the guidance of crystalline mineral applications and the prediction of material properties regarding mineral dissolution variation.
- 11 December 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (51) , 19008-19015
Discontinuous Dissolution Mechanism of Olivine Deduced from a Topography Observation Method
Olivine dissolution plays an important role in environmental science and technology, from controlling global element circulation to carbon capture for climate change mitigation. Most studies have been focused on investigating its dissolution rates by monitoring chemical effluent changes under various conditions. However, only by observation of surface reactivity can we unravel the actual mechanism (s) of dissolution. Here, we studied the dissolution of an olivine (010) plane in a flow-through reaction cell with an acidic solution, a surface-controlled regime, and far-from-equilibrium conditions. Direct mineral surface topography measurements using vertical scanning interferometry and atomic force microscopy allowed for quantitative analyses of the spatial and temporal changes in the dissolution rate. The (010) plane dissolved discontinuously in time for different surface sites, resulting in a heterogeneously distributed rate map. Pits with different depths showed opposite dissolution rate distributions from the dislocation center to further out from the etch pit. Based on the step-wave model, we propose a mechanism of dissolution that is governed by the competition between Gibbs free energy of the dissolution process, Delta G, and the critical free energy of the opening of etch pits, i.e., Delta G(crit). The migration of step waves, the distribution of surface defects, the strain field of etch pits, and other dynamic elements, resulting in the instantaneous change of Delta G(crit) on the surface, are important factors leading to the discontinuous dissolution of crystal materials. This discontinuous dissolution provides new insight into the guidance of crystalline mineral applications and the prediction of material properties regarding mineral dissolution variation.