František Bárnik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
František Bárnik has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Milan Sága
University of Zilina, Faculty of Mechanical Engineering, Univerzitná 1, 010 26, Žilina, Slovakia
2 shared publications- Milan Vaško
University of Žilina
2 shared publications Alžbeta Sapietová
University of Zilina, Faculty of Mechanical Engineering, Univerzitná 1, 010 26, Žilina, Slovakia
1 shared publication- Alžbeta Sapietová
Department of Applied Mechanics, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication F Dorčiak
Department of Applied Mechanics, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publicationM Handrik
Department of Applied Mechanics, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication
Latest Publications
- Open Access
- 1 February 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 776 (1)
Measurement and comparison study of deformation using extensometer and 2D DIC technology
The article deals with a short study of deformation measurement two different approaches. First is measurement by extensometer which is the contact technology and second is 2D DIC, which is the optical and contactless method of measurement. The paper starts with introduction to the 2D DIC measure method and continue with results of measurements of both methods. In the conclusion there is comparing results of two presented experimental methods.
- 1 February 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 776 (1)
Open AccessMeasurement and comparison study of deformation using extensometer and 2D DIC technology
The article deals with a short study of deformation measurement two different approaches. First is measurement by extensometer which is the contact technology and second is 2D DIC, which is the optical and contactless method of measurement. The paper starts with introduction to the 2D DIC measure method and continue with results of measurements of both methods. In the conclusion there is comparing results of two presented experimental methods.
- Open Access
- 15 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 254, 01018
Mechanical properties of structures produced by 3D printing from composite materials
By 3D printing it is possible to create different structures with different fiber-laying directions. These structures can be created depending on the type of 3D printer and its software. The Mark Two printer allows printing Onyx, a material based on nylon in combination with microcarbon fibers. Onyx can be used alone or reinforced with kevlar, glass or carbon fibers. This article deals with 3D printing and evaluation of mechanical properties of printed samples.
- 15 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 254, 01018
Open AccessMechanical properties of structures produced by 3D printing from composite materials
By 3D printing it is possible to create different structures with different fiber-laying directions. These structures can be created depending on the type of 3D printer and its software. The Mark Two printer allows printing Onyx, a material based on nylon in combination with microcarbon fibers. Onyx can be used alone or reinforced with kevlar, glass or carbon fibers. This article deals with 3D printing and evaluation of mechanical properties of printed samples.
- Open Access
- 5 December 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 244, 01022
Innovation of hardness tester mechanism and its functionality test
The article is focused on constructional design of device mechanism innovation. In the introduction is describe device and his original mechanism. Next section is focused on constructional design of device mechanism innovation and his describe. Another step is comparison between original mechanism and innovated mechanism. In the conclusion are evaluated theoretical and practical benefits of innovation.
- 5 December 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 244, 01022
Open AccessInnovation of hardness tester mechanism and its functionality test
The article is focused on constructional design of device mechanism innovation. In the introduction is describe device and his original mechanism. Next section is focused on constructional design of device mechanism innovation and his describe. Another step is comparison between original mechanism and innovated mechanism. In the conclusion are evaluated theoretical and practical benefits of innovation.