Natalia Vladimirovna Lishchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Natalia Vladimirovna Lishchenko has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Vasily Larshin
Odesa Polytechnic National University
6 shared publications V. P. Larshin
Odessa National Polytechnic University, 1 Shevchenko Ave., 65044 Odessa, Ukraine
4 shared publications- Ján Piteľ
Technical University of Košice
2 shared publications J. Pitel
Technical University of Kosice, 1 Bayerova St., 080 01 Presov, Slovakia
1 shared publicationOdessa National Academy Of Food Technologies
1 shared publicationOdessa National Polytechnic University
1 shared publication
Latest Publications
- 29 March 2021
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 4 (1) , 24-36
Virtual reality and real measurements in physical technology
- 29 March 2021
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 4 (1) , 24-36
Virtual reality and real measurements in physical technology
- 4 December 2020
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 3 (4) , 246-262
Complex-shaped parts grinding technology information ensuring
- 4 December 2020
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 3 (4) , 246-262
Complex-shaped parts grinding technology information ensuring
- 26 April 2020
- Published by Odessa Polytechnic National University in Herald of Advanced Information Technology
- Vol. 3 (1) , 61-71
DETECTING SYSTEMATIC AND RANDOM COMPONENT OF SURFACE ROUGHNESS SIGNAL
The solution of the problem of separating the initial one-dimensional signal into two components – systematic and random – has an extremely wide practical application not only in the theory of information and communication (and related disciplines), but also in mechanical engineering disciplines. For example, mechanical engineering technology being a science discipline includes the teaching about the surface quality of the machined parts and researching the surface roughness after machining these parts by cutting and grinding. The paper shows that the theoretical and actual values of roughness parameters differ significantly (up to 20 times) due to the influence of a random component that is present in the roughness signal together with a systematic component. It is necessary to identify the share of each of these components in the specified surface quality parameters in accordance with the method proposed in the paper. This method allows detecting the systematic and random components of the signal and is based on the analysis of the signal autocorrelation function. Practical examples of this analysis are considered in detail for milled surface profilogram obtained experimentally. Both milling, which creates irregularities on the machined surface, and measurement of these irregularities are performed on modern CNC equipment: machining center 500V/5 and computer measuring station T8000, respectively. The developed and shown by examples signal separation technique is also applicable in other fields of science, technology and manufacturing. For example, when determining the signal to noise ratio in the theory of information and communication, in the field of telecommunications and telemetry, radio engineering, etc.
- 26 April 2020
- Published by Odessa Polytechnic National University in Herald of Advanced Information Technology
- Vol. 3 (1) , 61-71
DETECTING SYSTEMATIC AND RANDOM COMPONENT OF SURFACE ROUGHNESS SIGNAL
The solution of the problem of separating the initial one-dimensional signal into two components – systematic and random – has an extremely wide practical application not only in the theory of information and communication (and related disciplines), but also in mechanical engineering disciplines. For example, mechanical engineering technology being a science discipline includes the teaching about the surface quality of the machined parts and researching the surface roughness after machining these parts by cutting and grinding. The paper shows that the theoretical and actual values of roughness parameters differ significantly (up to 20 times) due to the influence of a random component that is present in the roughness signal together with a systematic component. It is necessary to identify the share of each of these components in the specified surface quality parameters in accordance with the method proposed in the paper. This method allows detecting the systematic and random components of the signal and is based on the analysis of the signal autocorrelation function. Practical examples of this analysis are considered in detail for milled surface profilogram obtained experimentally. Both milling, which creates irregularities on the machined surface, and measurement of these irregularities are performed on modern CNC equipment: machining center 500V/5 and computer measuring station T8000, respectively. The developed and shown by examples signal separation technique is also applicable in other fields of science, technology and manufacturing. For example, when determining the signal to noise ratio in the theory of information and communication, in the field of telecommunications and telemetry, radio engineering, etc.
- 1 January 2020
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 7 (1) , A8-A16
Vibrational Impact on Milled Surface Irregularities
The methodology and results of a simultaneous study of causally linked parameters of mechanical vibration (cause) and surface irregularities (consequence) in flat milling with an end mill are given. The features of measurement and analysis of surface quality parameters through the application of the separation frequency method of profilogram harmonic components on the surface roughness, waviness, and the deviation of the profile are reviewed. A new method of profilogram digital processing is developed, comprising the steps of its digitization, low-pass filtering, and the formation of the roughness profile. The initial theoretical positions on modeling mechanical (elastic) waves which are caused by vibration in the cutting zone and propagate in a solid, liquid, and gas (air) media are presented. The results of experimental studies of milled surface profilogram and the vibro-displacement signal in the milling are given. Keywords: part performance, surface finish, surface integrity, vibro-acceleration, vibro-velocity, vibro-displacement, roughness, waviness, form deviation.
- 1 January 2020
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 7 (1) , A8-A16
Vibrational Impact on Milled Surface Irregularities
The methodology and results of a simultaneous study of causally linked parameters of mechanical vibration (cause) and surface irregularities (consequence) in flat milling with an end mill are given. The features of measurement and analysis of surface quality parameters through the application of the separation frequency method of profilogram harmonic components on the surface roughness, waviness, and the deviation of the profile are reviewed. A new method of profilogram digital processing is developed, comprising the steps of its digitization, low-pass filtering, and the formation of the roughness profile. The initial theoretical positions on modeling mechanical (elastic) waves which are caused by vibration in the cutting zone and propagate in a solid, liquid, and gas (air) media are presented. The results of experimental studies of milled surface profilogram and the vibro-displacement signal in the milling are given. Keywords: part performance, surface finish, surface integrity, vibro-acceleration, vibro-velocity, vibro-displacement, roughness, waviness, form deviation.
- 15 November 2019
- Published by Springer Nature
- p. 289-297
Gear-Grinding Temperature Modeling and Simulation
- 15 November 2019
- Published by Springer Nature
- p. 289-297
Gear-Grinding Temperature Modeling and Simulation
- 30 October 2019
- Published by Odessa Polytechnic National University in Herald of Advanced Information Technology
- Vol. 2 (3) , 197-205
GRINDING TEMPERATURE MODEL SIMPLIFICATION FOR THE OPERATION INFORMATION SUPPORT SYSTEM
Grinding temperature mathematic models need for the designing, monitoring and diagnosing the grinding operation to boost the operation throughput without burns of the surface to be ground. This is fully relevant, for example, for CNC gear grinding machines. Once the problem of mentioned mathematic models development is solved, it becomes possible to develop appropriate computer subsystems to optimize and control the grinding operation on CNC machines at the stages of both production and its preparation. The urgency of solving this problem is confirmed by the large number of relevant publications, most of them are connected with Jaeger moving heat source. At the same time, the idea of replacing the fast-moving source with the time of action of the corresponding unmoving one, formulated for the first time by Jaeger, has not yet found a proper practical application. This article justifiably shows that the proximity of the results of calculating the maximum grinding temperature and the depth of its penetration by the two- and one-dimensional solutions practically takes place when the fast-moving heat source is characterized by the Peclet number which is more than 4. For this interval of the Peclet number change, a simplified formula for grinding temperature was first obtained for determining the temperature on the surface and on the depth of the surface layer. Then this simplified formula was investigated by comparing it with the well-known analytical solution of the one-dimensional differential equation of heat conduction for various values of the Peclet number. It is shown that in the range of the Peclet number from 4 to 20, which is the case for most modern grinding operations (flat, round, profile, and others), the difference in determining the grinding temperature by exact and approximate solutions does not exceed 11%. At the same time, the simplified solution obtained in the paper has an important new quality. The mathematical formula that describes this solution makes it possible to express explicitly the penetration depth of any given fixed temperature. If this fixed temperature leads to structural-phase transformations in the surface layer of the workpiece, then it becomes possible to determine the defective layer depth during grinding. In turn, the grinding stock for the grinding operation should be greater than the mentioned defective layer depth. New information on the state of the grinding system can be the basis for monitoring and diagnosing of the operation, as well as for designing this operation at the stage of production preparation. This, in turn, is a technological prerequisite for the development of appropriate computer subsystems that can be integrated into the CNC system of modern grinding machines.
- 30 October 2019
- Published by Odessa Polytechnic National University in Herald of Advanced Information Technology
- Vol. 2 (3) , 197-205
GRINDING TEMPERATURE MODEL SIMPLIFICATION FOR THE OPERATION INFORMATION SUPPORT SYSTEM
Grinding temperature mathematic models need for the designing, monitoring and diagnosing the grinding operation to boost the operation throughput without burns of the surface to be ground. This is fully relevant, for example, for CNC gear grinding machines. Once the problem of mentioned mathematic models development is solved, it becomes possible to develop appropriate computer subsystems to optimize and control the grinding operation on CNC machines at the stages of both production and its preparation. The urgency of solving this problem is confirmed by the large number of relevant publications, most of them are connected with Jaeger moving heat source. At the same time, the idea of replacing the fast-moving source with the time of action of the corresponding unmoving one, formulated for the first time by Jaeger, has not yet found a proper practical application. This article justifiably shows that the proximity of the results of calculating the maximum grinding temperature and the depth of its penetration by the two- and one-dimensional solutions practically takes place when the fast-moving heat source is characterized by the Peclet number which is more than 4. For this interval of the Peclet number change, a simplified formula for grinding temperature was first obtained for determining the temperature on the surface and on the depth of the surface layer. Then this simplified formula was investigated by comparing it with the well-known analytical solution of the one-dimensional differential equation of heat conduction for various values of the Peclet number. It is shown that in the range of the Peclet number from 4 to 20, which is the case for most modern grinding operations (flat, round, profile, and others), the difference in determining the grinding temperature by exact and approximate solutions does not exceed 11%. At the same time, the simplified solution obtained in the paper has an important new quality. The mathematical formula that describes this solution makes it possible to express explicitly the penetration depth of any given fixed temperature. If this fixed temperature leads to structural-phase transformations in the surface layer of the workpiece, then it becomes possible to determine the defective layer depth during grinding. In turn, the grinding stock for the grinding operation should be greater than the mentioned defective layer depth. New information on the state of the grinding system can be the basis for monitoring and diagnosing of the operation, as well as for designing this operation at the stage of production preparation. This, in turn, is a technological prerequisite for the development of appropriate computer subsystems that can be integrated into the CNC system of modern grinding machines.
- 1 January 2019
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 2 (4) , 304-316
Comparison of measured surface layer quality parameters with simulated results
The grinding temperature is one of the factors limiting the throughput performance of the profile gear grinding operation. There are two main methods for determining the grinding temperature: an analytical method with the aid of analytical models and a simula-tion one based on both the analytical and geometrical models. In the paper, at the first stage the profile gear grinding temperature field is investigated with the aid of finite element method (FEM) simulation as an example of information technology which helps to predict the surface layer quality physical parameters. The results obtained are compared with similar calculations for the analytical models and the tooth surface area is found to determine the temperature according with the analytical models. At the second stage, a series of experimental studies on the CNC machine Höfler Rapid 1250 is carried out on a real gear by means of a successive increase in the depth of profile gear grinding. From the gear machined the special samples were cut out on the electro-erosive machine mod. MV 2400S ADVANCE Type 2 (MITSUBISHI ELECTRIC Company) for additional investigation of these samples. The teeth sur-face layer quality experimental study and the structural-phase state of the surface layer metallographic analysis have been performed using modern measuring equipment and instruments, e.g. microscope Altami MET-5. It is established that, in other equal conditions, the highest grinding temperature occurs in the upper part of the tooth which is grinding. It is identified areas of the tooth profile, on which the grinding temperature can be calculated by the famous analytical dependencies. It is established that as the parameters char-acterizing the grinding intensity and the volume of material removal per unit of the grinding wheel width increase, the grinding burn arises and its thickness increases. The regularity of the change in the thickness of the burn along the height of the tooth is established, which makes it possible to evaluate the reliability of the corresponding theoretical studies.
- 1 January 2019
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 2 (4) , 304-316
Comparison of measured surface layer quality parameters with simulated results
The grinding temperature is one of the factors limiting the throughput performance of the profile gear grinding operation. There are two main methods for determining the grinding temperature: an analytical method with the aid of analytical models and a simula-tion one based on both the analytical and geometrical models. In the paper, at the first stage the profile gear grinding temperature field is investigated with the aid of finite element method (FEM) simulation as an example of information technology which helps to predict the surface layer quality physical parameters. The results obtained are compared with similar calculations for the analytical models and the tooth surface area is found to determine the temperature according with the analytical models. At the second stage, a series of experimental studies on the CNC machine Höfler Rapid 1250 is carried out on a real gear by means of a successive increase in the depth of profile gear grinding. From the gear machined the special samples were cut out on the electro-erosive machine mod. MV 2400S ADVANCE Type 2 (MITSUBISHI ELECTRIC Company) for additional investigation of these samples. The teeth sur-face layer quality experimental study and the structural-phase state of the surface layer metallographic analysis have been performed using modern measuring equipment and instruments, e.g. microscope Altami MET-5. It is established that, in other equal conditions, the highest grinding temperature occurs in the upper part of the tooth which is grinding. It is identified areas of the tooth profile, on which the grinding temperature can be calculated by the famous analytical dependencies. It is established that as the parameters char-acterizing the grinding intensity and the volume of material removal per unit of the grinding wheel width increase, the grinding burn arises and its thickness increases. The regularity of the change in the thickness of the burn along the height of the tooth is established, which makes it possible to evaluate the reliability of the corresponding theoretical studies.
- 1 January 2019
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 2 (3) , 216-229
Temperature models for grinding system state monitoring
The grinding temperature limits the productivity of this operation and is an important parameter for assessing the state of the grinding system. However, there is no information about the current grinding temperature in the existing computer systems for moni-toring and process diagnostics on CNC grinding machines. This is due to the difficulty of measuring this parameter directly or indi-rectly. In the first case – difficulty with the installation of temperature sensors, in the second – there are no acceptable mathematical models for determining the grinding temperature. The objective of the study is development of a simpler temperature model which is acceptable for the modern grinding with large values of the workpiece velocity relative to the grinding wheel. To reach the study objective a classification of solutions of three-, two-, and one-dimensional differential equations of heat conduction with the same initial and boundary conditions was made to research the grinding temperatures with the help of these solutions under otherwise equal conditions. The conditions of results close agreement of the solutions are established depending on the geometrical configura-tion of the contact zone between the grinding wheel and the workpiece: H / L4, where HandL are half width and half length of the contact zone, respectively. The above three solutions of differential heat conduction equations obtained under boundary conditions of the second kind and were converted to a uniform dimensionless form, in which the dimensionless temperature depends on the coordinate and dimensionless time multiplicity of the Peclet number, which characterizes this time, the dimensionless half and velocity of the moving heat source. A comparative analysis of surface and deep temperatures was performed for the above three solu-tions depending on the Peclet number. The possibility of determining the grinding temperature on modern high-speed CNC machines with a one-dimensional solution with H>4 on the basis of computer subsystems of designing, monitoring and diagnosing of grind-ing operations is shown.
- 1 January 2019
- Published by Odessa Polytechnic National University in Applied Aspects of Information Technology
- Vol. 2 (3) , 216-229
Temperature models for grinding system state monitoring
The grinding temperature limits the productivity of this operation and is an important parameter for assessing the state of the grinding system. However, there is no information about the current grinding temperature in the existing computer systems for moni-toring and process diagnostics on CNC grinding machines. This is due to the difficulty of measuring this parameter directly or indi-rectly. In the first case – difficulty with the installation of temperature sensors, in the second – there are no acceptable mathematical models for determining the grinding temperature. The objective of the study is development of a simpler temperature model which is acceptable for the modern grinding with large values of the workpiece velocity relative to the grinding wheel. To reach the study objective a classification of solutions of three-, two-, and one-dimensional differential equations of heat conduction with the same initial and boundary conditions was made to research the grinding temperatures with the help of these solutions under otherwise equal conditions. The conditions of results close agreement of the solutions are established depending on the geometrical configura-tion of the contact zone between the grinding wheel and the workpiece: H / L4, where HandL are half width and half length of the contact zone, respectively. The above three solutions of differential heat conduction equations obtained under boundary conditions of the second kind and were converted to a uniform dimensionless form, in which the dimensionless temperature depends on the coordinate and dimensionless time multiplicity of the Peclet number, which characterizes this time, the dimensionless half and velocity of the moving heat source. A comparative analysis of surface and deep temperatures was performed for the above three solu-tions depending on the Peclet number. The possibility of determining the grinding temperature on modern high-speed CNC machines with a one-dimensional solution with H>4 on the basis of computer subsystems of designing, monitoring and diagnosing of grind-ing operations is shown.
- 7 December 2018
- Published by Springer Nature
- p. 1723-1730
Profile Gear Grinding Temperature Determination
- 7 December 2018
- Published by Springer Nature
- p. 1723-1730
Profile Gear Grinding Temperature Determination
- 1 January 2018
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 5 (1) , A 1-A 7
Profile Gear Grinding Temperature Reduction and Equalization
- 1 January 2018
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 5 (1) , A 1-A 7
Profile Gear Grinding Temperature Reduction and Equalization