DBDiego Felipe Mona Boada

Diego Felipe Mona Boada

*This is an algorithmically generated author record based on publicly available information.

Diego Felipe Mona Boada has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Synthesis of Circularly Polarized Cylindrical Microstrip Antennas

    by Diego F. Mona Boada, Daniel C. Nascimento

    A set of new formulations derived from the cavity model (CM) that significantly improve the design of cylindrical single probe-fed circularly polarized rectangular microstrip antennas (CPRMA) are presented in this paper. Comprehensive analysis shows that differentiation of the dominant modes effective loss tangents in the far-field expressions gives rise to new closed-form design equations suitable for electrically thin antennas, extending the applicability and improving the CM accuracy for electrically small and large radii cylinders. Furthermore, a function is proposed to estimate the minimal number of significant terms needed in the far-field infinite series to portray the fields radiated by the antenna accurately. The proposed formulations are also used as part of an iterative cavity model-based algorithm that fully solves the issue of synthesizing a cylindrical CPRMA for a user-defined input impedance. Several antenna examples are compared to full-wave simulations to demonstrate the algorithm’s accuracy. To validate the proposed formulations, a right-hand circularly polarized cylindrical antenna prototype is designed and built to operate at 1.575 GHz over a cylinder with a radius of 25 mm. Comparisons between theoretical and experimental results show excellent agreement.


  • Open Access

    Co-Design of a GPS Antenna Low-Noise Amplifier Front-End Circuit

    by Eduardo S. Sakomura, Diego F. M. Boada, Daniel C. Nascimento

    This paper presents a clear and fast design procedure for directly matched low noise active integrated microstrip antenna front end circuits. Initially, a theoretical analysis is given for the overall gain equivalence between traditional and directly matched antennas. Then, a detailed procedure is presented for the design and construction of a fully integrated GPS antenna. To validate the proposed procedure, a prototype was built and characterized by measuring the reflection coefficient, radiation pattern, noise figure and the active antenna overall gain. Additionally, a field test comparison was made between the manufactured prototype and a commercially available active antenna using the u-blox NEO-6M GPS receiver module. The prototype experimental and field test results showed excellent performance, thus validating the proposed co-design approach.

  • Performance Analysis of Azimuth-Only Amplitude-Comparison DF System in Operational Scenarios

    by E. S. Sakomura, D. B. Ferreira, I. Bianchi, D. C. Nascimento, D. F. Mona

    This paper presents a performance analysis of an azimuth-only amplitude-comparison direction finding (DF) system in operational scenarios. The DF system is composed of two-squinted cavity-backed spiral antennas and it can move while in operation. Initially, the DF system is calibrated by using the spirals embedded element patterns, being the resulting calibration residual errors evaluated at frequencies in the range from 1 to 18 GHz. Errors obtained are lower than 1° rms. The azimuth angular errors are then computed considering sources not polarization matched to the spiral antennas and the system moving on paths whose heights may change with time. Full-wave simulations are run to estimate the radiation data needed for evaluation.

  • Mechanical Tension Effects on Cylindrical Truncated-Corner Microstrip Antennas

    by D. F. Mona, E. S. Sakomura, D. C. Nascimento, D. B. Ferreira

    The experimental characterization of the mechanical tension effects on a 2.25-GHz probe-fed rectangular truncated-corner microstrip antenna conformed on a cylindrical surface is presented in this work. Two prototypes were designed and built for a metallic cylinder with a diameter of 12.55 centimeters. The first antenna was used to characterize the effects of mechanical tension considering the manufacture after etch stress relief effect. A comparison between simulated and experimental results for the first prototype showed that the conformed patch is elongated along the curvature of the metallic cylinder by 0.56 millimeters. The patch elongation was then compensated on the second prototype. Experimental data proved that the elongation was characterized correctly.

  • Analysis of Cross- and X-Shaped Spiral Antenna Arrays for Amplitude-Comparison DF Systems

    by E. S. Sakomura, D. B. Ferreira, I. Bianchi, D. C. Nascimento, D. F. Mona

    This paper presents a performance analysis of cross- and X-shaped arrays of cavity-backed spiral antennas for amplitude-comparison direction finding (ACDF) systems. First, an effective calibration strategy for the ACDF system is proposed, which uses the embedded element patterns to improve the accuracy of the evaluated calibration coefficients. As will be seen, both cross- and X-shaped arrays show calibration residual error values lower than 1° rms. Finally, the ACDF system angular error values are quantified for sources which are not polarization matched to the spiral antennas. Full-wave simulations are run to estimate the arrays radiation performances in the range from 1 to 18 GHz.

  • Including the Effects of Curvature in the Cavity Model and New Manufacturing Considerations for Cylindrical Microstrip Antennas

    by Diego Felipe Mona Boada, Daniel Chagas Do Nascimento

    This letter presents an insightful and significant improvement of the cylindrical cavity model and an experimental methodology to compensate the mechanical bending effects on cylindrical microstrip antennas. In the first part of this document, by studying analytical and numerical results from a non-radiating resonant rectangular cavity, a new function for the resonant length of the circumferential mode that is governed by the antenna thickness and cylinder radius was determined. In the second part, an experimental methodology is presented to compensate the copper elongation effect due to bending. To validate the proposed techniques, a circularly polarized rectangular microstrip antenna was designed and built to operate at 2.2 GHz with an input impedance of 50 Ω for a metallic cylinder with a radius of 25 cm. The experimental results showed that the new approaches to calculate the circumferential resonant frequency and elongation effect due to bending improved significantly the cylindrical antenna design.


  • Available Universe of Input Impedances for the Probe-Fed Circularly Polarized Microstrip Antenna

    by D. F. Mona, D. C. Nascimento

    In this work, through the cavity model, the universe of achievable input impedances generated by the probe-fed circularly polarized rectangular microstrip antenna is investigated. Results of the analysis at the frequency of operation are displayed on an easy to use graphic. To prove the concept, an antenna was designed with an input impedance located in the predicted universe.

  • Microstrip-to-Probe Fed Microstrip Antenna Transition

    by D. F. Mona, E. S. Sakomura, D. C. Nascimento

    This paper presents an accurate and simple method to model the transition between a probe-fed microstrip antenna and a microstrip circuit, assembled in a back-to-back configuration. With the aid of a full-wave electromagnetic simulation tool the two-port S-parameter matrix of the transition is calculated. This information is used to determine the antenna input impedance (Z A ) that enforces a given impedance (Z in ) after the transition. To showcase the applicability and validate the proposed method a co-designed GPS active integrated antenna was designed and manufactured.


  • Mechanical Tension Effects on Cylindrical Probe-Fed Circularly Polarized Microstrip Antennas

    by D. F. Mona, E. S. Sakomura, D. C. Nascimento

    The experimental characterization of the mechanical tension effects on a 2. 2 GHz probe fed circularly polarized rectangular microstrip antenna conformed on a cylindrical surface is presented in this work. Two prototypes were designed and built for a metallic cylinder with a radius of 25 centimeters and height of 1. 5 meters. The first antenna was used to characterize the effects of mechanical tension, also considering permittivity uncertainty and the manufacture after etch stress relief effect. A comparison between numerical and experimental results from the first prototype showed that the conformed patch is elongated along the curvature of the metallic cylinder approximately by 0.15 millimeters. The patch elongation was compensated on the second prototype. Experimental measurements showed that the elongation was predicted accurately.


  • Open Access

    Circularly polarised rectangular microstrip antenna design with arbitrary input impedance

    by Diego F. Moná, Eduardo S. Sakomura, Daniel C. Nascimento

    This study describes two stand‐alone iterative algorithms that fully solve the issue of generating non‐standard input impedances in probe‐fed circularly polarised rectangular microstrip antennas (CPRMA). Both were derived from a new cavity model‐based methodology that controls, at the frequency of operation ( ), the input reactance and resistance levels without disturbing the circular polarisation (CP) characteristics of the antenna. The first algorithm finds the antenna dimensions and probe position for an arbitrarily selectable input impedance and the second algorithm determines the possible choices of input impedance for a given dielectric substrate and . To highlight the applicability of both algorithms, two prototypes were designed and built: a right‐hand CP (RHCP) active antenna with input impedance , and an RHCP reference antenna (RA) with input impedance . These antennas were utilised in the design and characterisation of a co‐designed global positioning system active integrated antenna. The experimental and theoretical results show excellent agreement.