Arif Khan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arif Khan has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Shaibal Mukherjee
Hybrid Nanodevice Research Group (HNRG), Department of Electrical Engineering Indian Institute of Technology Indore Indore Madhya Pradesh India
15 shared publications - Rohit Singh
Electrical Engineering, Indian Institute of Technology Indore
8 shared publications - Abhinav Kranti
Department of Electrical Engineering, Low Power Nanoelectronics Research Group, Indian Institute of Technology Indore, Indore, India
5 shared publications - Karen Geens
IMEC, Kapeldreef 75, Leuven, Flanders, 3001, BELGIUM
5 shared publications - Stefaan Decoutere
IMEC, 3001 Leuven, Belgium
5 shared publications - Anurag Vohra
IMEC, Leuven, Belgium
4 shared publications
Latest Publications
- 24 March 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (14)
Overview of defect characterization on GaN stacks for vertical device fabrication on 200 mm engineered QST® substrates
The increasing demand for high-voltage (> 1200 V) power devices has driven the epitaxy of thick GaN buffers on top of mechanically robust substrates such as engineered QST® substrates. This study investigates the material crystalline defects in vertical GaN buffers grown via metalorganic chemical vapor deposition (MOCVD) on 200 mm QST®, with and without pre-grown epitaxial lateral overgrown (ELOG) buffers. We present a systematic analysis of the threading dislocation density (TDD) using several destructive and non-destructive techniques such as transmission electron microscope (TEM), cathodoluminescence (CL), electron channelling contrast imaging (ECCI,) X-ray diffraction (XRD) and scanning probe microscopy (SPM). They reveal different dislocation types; i.e., edge, mixed and screw threading dislocations (TD). TEM reveals a ~ 5 times TDD reduction for stacks employing ELOG buffers. ECCI, CL and XRD complement one another with ~ 2 – 2.5 times reduced TDD on ELOG buffer. Whereas CL reveals all TDs involved in non-radiative recombination, ambiguity remains in ascribing the specific TD type. ECCI primarily identifies mixed TD. XRD analyses of GaN(0002) and (10-12) reflections reveal a systematic improvement of crystal quality with increasing drift layer (DL) thickness. ELOG buffer reveals ~ 4 times stronger screw TD reduction and > 6 times stronger edge TD reduction with increasing DL thickness, compared to the one without. Conductive AFM (c-AFM) measurements show that only ~ 0.1–0.2% of total TDs are electrically active contributing to vertical leakage, with > 3 times reduction of such TD on ELOG buffer. Cross-sectional SPM, CL and ECCI imaging further validate the reduced defectivity in ELOG-enabled stacks. The scanning capacitance microscope (SCM) |dC/dV| maps show reduced amplitude at defect sites and CL imaging clearly visualizes these darker non-radiative recombination regions, whereas ECCI complements these observations. In summary, this study presents a comprehensive defectivity analysis of GaN-on-QST® substrates with ELOG buffers, demonstrating their potential for vertical GaN device fabrication and up-scaling.
- 24 March 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (14)
Overview of defect characterization on GaN stacks for vertical device fabrication on 200 mm engineered QST® substrates
The increasing demand for high-voltage (> 1200 V) power devices has driven the epitaxy of thick GaN buffers on top of mechanically robust substrates such as engineered QST® substrates. This study investigates the material crystalline defects in vertical GaN buffers grown via metalorganic chemical vapor deposition (MOCVD) on 200 mm QST®, with and without pre-grown epitaxial lateral overgrown (ELOG) buffers. We present a systematic analysis of the threading dislocation density (TDD) using several destructive and non-destructive techniques such as transmission electron microscope (TEM), cathodoluminescence (CL), electron channelling contrast imaging (ECCI,) X-ray diffraction (XRD) and scanning probe microscopy (SPM). They reveal different dislocation types; i.e., edge, mixed and screw threading dislocations (TD). TEM reveals a ~ 5 times TDD reduction for stacks employing ELOG buffers. ECCI, CL and XRD complement one another with ~ 2 – 2.5 times reduced TDD on ELOG buffer. Whereas CL reveals all TDs involved in non-radiative recombination, ambiguity remains in ascribing the specific TD type. ECCI primarily identifies mixed TD. XRD analyses of GaN(0002) and (10-12) reflections reveal a systematic improvement of crystal quality with increasing drift layer (DL) thickness. ELOG buffer reveals ~ 4 times stronger screw TD reduction and > 6 times stronger edge TD reduction with increasing DL thickness, compared to the one without. Conductive AFM (c-AFM) measurements show that only ~ 0.1–0.2% of total TDs are electrically active contributing to vertical leakage, with > 3 times reduction of such TD on ELOG buffer. Cross-sectional SPM, CL and ECCI imaging further validate the reduced defectivity in ELOG-enabled stacks. The scanning capacitance microscope (SCM) |dC/dV| maps show reduced amplitude at defect sites and CL imaging clearly visualizes these darker non-radiative recombination regions, whereas ECCI complements these observations. In summary, this study presents a comprehensive defectivity analysis of GaN-on-QST® substrates with ELOG buffers, demonstrating their potential for vertical GaN device fabrication and up-scaling.
- Open Access
- 9 January 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (2)
Poole–Frenkel emission and bulk charge trapping in AlON deposited on GaN and comparison to Al2O3
The leakage conduction mechanisms in AlON dielectric deposited on GaN are identified and compared to the findings for Al2O3. Poole–Frenkel emission from similar trap energy levels was identified in both atomic layer deposited AlON and Al2O3¸ despite at different electric field ranges, while Fowler–Nordheim tunneling dominated the leakage current characteristics for Al2O3 at average electric field values. It is concluded that the differences observed in the leakage characteristics for these dielectrics are likely a result of the slightly larger conduction band offset between AlON and GaN. The identification of the same trap state energy level responsible for Poole–Frenkel emission in AlON and Al2O3 means that this trap state does not originate from the presence of nitrogen in the dielectric and is related to AlOx compounds and the deposition method. Bulk charge trapping is shown to play a major role in the leakage characteristics of AlON from average to high electric fields, which shifts the transfer characteristics from a certain electric field onward and causes hysteresis. These results provide valuable insights into the development of insulated gate architectures on GaN using the promising dielectric material AlON as the gate oxide.
- 9 January 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (2)
Open AccessPoole–Frenkel emission and bulk charge trapping in AlON deposited on GaN and comparison to Al2O3
The leakage conduction mechanisms in AlON dielectric deposited on GaN are identified and compared to the findings for Al2O3. Poole–Frenkel emission from similar trap energy levels was identified in both atomic layer deposited AlON and Al2O3¸ despite at different electric field ranges, while Fowler–Nordheim tunneling dominated the leakage current characteristics for Al2O3 at average electric field values. It is concluded that the differences observed in the leakage characteristics for these dielectrics are likely a result of the slightly larger conduction band offset between AlON and GaN. The identification of the same trap state energy level responsible for Poole–Frenkel emission in AlON and Al2O3 means that this trap state does not originate from the presence of nitrogen in the dielectric and is related to AlOx compounds and the deposition method. Bulk charge trapping is shown to play a major role in the leakage characteristics of AlON from average to high electric fields, which shifts the transfer characteristics from a certain electric field onward and causes hysteresis. These results provide valuable insights into the development of insulated gate architectures on GaN using the promising dielectric material AlON as the gate oxide.
- 15 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (24)
Low-stress MOCVD-grown 15 μm GaN layers on 200 mm engineered substrates with minimal wafer bow
Gallium nitride is increasingly recognized as a leading material for power and radio frequency applications, due to its unique electronic properties. However, the phenomenon of wafer bow and warpage during GaN growth on heterogeneous substrates presents significant challenges for vertical-type GaN devices with increasing drift layer thickness (for high voltage applications, 1200 V and above) and substrate diameters scaling to 200 mm. In this study, we introduce a growth scheme in the metalorganic chemical vapor deposition of GaN on 200 mm “engineered” substrates from Qromis substrate technology, specifically to minimize the wafer bow for vertical GaN metal-oxide-semiconductor field-effect transistors featuring an 11.5 μm-thick drift layer, with an overall GaN stack of ∼15 μm. By systematically reducing the pressure during the growth of unintentionally doped GaN from 300 to 150 mbar on an Al0.3Ga0.7N buffer layer, the tensile stress induced during cooldown could be effectively compensated. This yields an overall low residual stress of the thick ∼15 μm epitaxially grown GaN layers on the engineered Qromis substrate technology® substrate.
- 15 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (24)
Low-stress MOCVD-grown 15 μm GaN layers on 200 mm engineered substrates with minimal wafer bow
Gallium nitride is increasingly recognized as a leading material for power and radio frequency applications, due to its unique electronic properties. However, the phenomenon of wafer bow and warpage during GaN growth on heterogeneous substrates presents significant challenges for vertical-type GaN devices with increasing drift layer thickness (for high voltage applications, 1200 V and above) and substrate diameters scaling to 200 mm. In this study, we introduce a growth scheme in the metalorganic chemical vapor deposition of GaN on 200 mm “engineered” substrates from Qromis substrate technology, specifically to minimize the wafer bow for vertical GaN metal-oxide-semiconductor field-effect transistors featuring an 11.5 μm-thick drift layer, with an overall GaN stack of ∼15 μm. By systematically reducing the pressure during the growth of unintentionally doped GaN from 300 to 150 mbar on an Al0.3Ga0.7N buffer layer, the tensile stress induced during cooldown could be effectively compensated. This yields an overall low residual stress of the thick ∼15 μm epitaxially grown GaN layers on the engineered Qromis substrate technology® substrate.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5212-5217
Electrical Stability of MOS Structures With AlON and Al₂O₃ Dielectrics Deposited on n- and p-Type GaN
This article discusses the electrical stability of MOS structures on n- and p-type GaN for two different dielectrics, AlON and Al2O3, deposited by atomic layer deposition (ALD). Threshold voltage hysteresis was evaluated by means of capacitance–voltage (C–V) double sweep measurements, performed on MOS capacitors. MOS structures on p-doped GaN show up to two orders of magnitude higher effective trapped charge density than on n-GaN. Moreover, AlON results in 10 times less trapped charge than Al2O3 on p-GaN. The leakage current is also identified as an important factor in defining the electrical stability at high electric fields, due to the enhanced injection of electrons into the MOS stack. Electron trapping is shown to happen either at the dielectric–semiconductor interface or in border traps. AlON results in lower flat-band and threshold voltages likely due to the resulting fixed interface charge from surface reconstruction. The effect of the n-type doping density as well as of dry etch damage on the effective trapped charge after injection has been shown to be minimal. These results are important for different insulated gate device architectures. We show that extremely low threshold voltage hysteresis values can be reached in a trench-shaped gate GaN MOSFET using AlON as an interface dielectric.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5212-5217
Electrical Stability of MOS Structures With AlON and Al₂O₃ Dielectrics Deposited on n- and p-Type GaN
This article discusses the electrical stability of MOS structures on n- and p-type GaN for two different dielectrics, AlON and Al2O3, deposited by atomic layer deposition (ALD). Threshold voltage hysteresis was evaluated by means of capacitance–voltage (C–V) double sweep measurements, performed on MOS capacitors. MOS structures on p-doped GaN show up to two orders of magnitude higher effective trapped charge density than on n-GaN. Moreover, AlON results in 10 times less trapped charge than Al2O3 on p-GaN. The leakage current is also identified as an important factor in defining the electrical stability at high electric fields, due to the enhanced injection of electrons into the MOS stack. Electron trapping is shown to happen either at the dielectric–semiconductor interface or in border traps. AlON results in lower flat-band and threshold voltages likely due to the resulting fixed interface charge from surface reconstruction. The effect of the n-type doping density as well as of dry etch damage on the effective trapped charge after injection has been shown to be minimal. These results are important for different insulated gate device architectures. We show that extremely low threshold voltage hysteresis values can be reached in a trench-shaped gate GaN MOSFET using AlON as an interface dielectric.
- 11 March 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (11)
Mg activation anneal of the p-GaN body in trench gate MOSFETs and its effect on channel mobility and threshold voltage stability
This work addresses the impact of the Mg activation anneal step and the resulting acceptor concentration on the channel mobility and VT stability of vertical MOSFETs. Increasing the annealing time with N2 only ambient and the annealing temperature with O2 in the ambient is shown to be effective in increasing the channel acceptor concentration. When the effective acceptor concentration is increased, the mobility is degraded due to a transition in the main scattering mechanism from Coulomb to surface roughness scattering. Degradation of the on-state current and maximum transconductance at high operating temperatures was linked to bulk mobility degradation of the drift layer due to lattice scattering. The two Mg activation annealing conditions considered here show different trends with regard to the threshold voltage stability, while N2 only ambient did not impact this parameter, including O2 increased threshold voltage instability. It is shown that increasing the Mg chemical concentration in the p-GaN layer degrades channel mobility and threshold voltage stability, irrespectively of the effective acceptor concentration, providing evidence for degradation of the channel/dielectric interface characteristics with higher Mg chemical concentration. This study shows that it is possible to achieve very low threshold voltage hysteresis and high channel mobility by reducing the Mg chemical concentration while maintaining high effective acceptor concentration. These results provide key insights for the development of vertical GaN FETs.
- 11 March 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (11)
Mg activation anneal of the p-GaN body in trench gate MOSFETs and its effect on channel mobility and threshold voltage stability
This work addresses the impact of the Mg activation anneal step and the resulting acceptor concentration on the channel mobility and VT stability of vertical MOSFETs. Increasing the annealing time with N2 only ambient and the annealing temperature with O2 in the ambient is shown to be effective in increasing the channel acceptor concentration. When the effective acceptor concentration is increased, the mobility is degraded due to a transition in the main scattering mechanism from Coulomb to surface roughness scattering. Degradation of the on-state current and maximum transconductance at high operating temperatures was linked to bulk mobility degradation of the drift layer due to lattice scattering. The two Mg activation annealing conditions considered here show different trends with regard to the threshold voltage stability, while N2 only ambient did not impact this parameter, including O2 increased threshold voltage instability. It is shown that increasing the Mg chemical concentration in the p-GaN layer degrades channel mobility and threshold voltage stability, irrespectively of the effective acceptor concentration, providing evidence for degradation of the channel/dielectric interface characteristics with higher Mg chemical concentration. This study shows that it is possible to achieve very low threshold voltage hysteresis and high channel mobility by reducing the Mg chemical concentration while maintaining high effective acceptor concentration. These results provide key insights for the development of vertical GaN FETs.
- Open Access
- 29 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1488-1493
Route Toward Commercially Manufacturable Vertical GaN Devices
To make vertical GaN-based trench gate MOSFET devices commercially manufacturable, 200 mm engineered substrates with a poly-AlN core are a good substrate choice. The poly-AlN core, matched in thermal expansion to GaN, allows to grow high-quality thick GaN layers. Up to 11 $\mu$ m-thick GaN stacks were grown crack-free, with excellent control over the wafer warp. Breakdown values of 900 V were reached for the vertical p/n-junction. Full device processing was completed in a CMOS-compatible pilot line without any wafer breakage, demonstrating the mechanical strength of these substrates. On module level, a new gate trench profile combining a smooth sidewall and round corners, is presented. While a smooth sidewall is important for the ON-state performance of the devices, the rounded corners are beneficial for the OFF-state operation. A semi-vertical test vehicle was used to demonstrate the ON-state of the fabricated power transistors. For devices with an effective gate width ( $\textit{W}_{\text{G,\text{ef}\text{f}}}\text{)}$ of 180 mm and an active area of 1.4 mm $^{\text{2}}$ , an ON-state resistance could be achieved of 8 m $\Omega\cdot \text{cm}^{\text{2}}$ . By scaling the source contact length down, the device footprint could be decreased further. It is shown that for devices with a $\textit{W}_{\text{G,\text{ef}\text{f}}}$ of 60 mm this value could be further improved with best performing devices showing a 6.2 m $\Omega\cdot\text{ cm}^{\text{2}}$ ON-state resistance.
- 29 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1488-1493
Open AccessRoute Toward Commercially Manufacturable Vertical GaN Devices
To make vertical GaN-based trench gate MOSFET devices commercially manufacturable, 200 mm engineered substrates with a poly-AlN core are a good substrate choice. The poly-AlN core, matched in thermal expansion to GaN, allows to grow high-quality thick GaN layers. Up to 11 $\mu$ m-thick GaN stacks were grown crack-free, with excellent control over the wafer warp. Breakdown values of 900 V were reached for the vertical p/n-junction. Full device processing was completed in a CMOS-compatible pilot line without any wafer breakage, demonstrating the mechanical strength of these substrates. On module level, a new gate trench profile combining a smooth sidewall and round corners, is presented. While a smooth sidewall is important for the ON-state performance of the devices, the rounded corners are beneficial for the OFF-state operation. A semi-vertical test vehicle was used to demonstrate the ON-state of the fabricated power transistors. For devices with an effective gate width ( $\textit{W}_{\text{G,\text{ef}\text{f}}}\text{)}$ of 180 mm and an active area of 1.4 mm $^{\text{2}}$ , an ON-state resistance could be achieved of 8 m $\Omega\cdot \text{cm}^{\text{2}}$ . By scaling the source contact length down, the device footprint could be decreased further. It is shown that for devices with a $\textit{W}_{\text{G,\text{ef}\text{f}}}$ of 60 mm this value could be further improved with best performing devices showing a 6.2 m $\Omega\cdot\text{ cm}^{\text{2}}$ ON-state resistance.
- 16 February 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (3) , 035021
Physical design guidelines to minimize area-specific ON-resistance for rated ON-current and breakdown voltage of GaN power HEMTs
In this article, we report on the development of an analytical model to estimate area-specific ON-state resistance (R ds,on) of GaN-based power high electron mobility transistor (HEMT) using rated device specifications—ON-state drain current (I ON) and maximum operating drain-to-source voltage (V DSO)—as input parameters. The rated I ON and V DSO are considered as fractions k and S, of the maximum possible drain current (I DS,max) and breakdown voltage (V BR), respectively, deliverable by the power device. The developed model is utilized to obtain the optimal physical design space parameters for a comb-like power HEMT design. Due consideration has been given to the trade-off between R ds,on and area-specific R ds,on of the transistor, device processing limitations for all the physical device parameters. The developed model has been validated with experimental results of prior literature. Our calculations impose a lower-bound for the best possible R ds,on as well as the area-specific on-resistance product (R ds,on × AA) that can be obtained for a given starting channel sheet resistance in the comb architecture for a desired I ON − V DSO rating.
- 16 February 2023
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 38 (3) , 035021
Physical design guidelines to minimize area-specific ON-resistance for rated ON-current and breakdown voltage of GaN power HEMTs
In this article, we report on the development of an analytical model to estimate area-specific ON-state resistance (R ds,on) of GaN-based power high electron mobility transistor (HEMT) using rated device specifications—ON-state drain current (I ON) and maximum operating drain-to-source voltage (V DSO)—as input parameters. The rated I ON and V DSO are considered as fractions k and S, of the maximum possible drain current (I DS,max) and breakdown voltage (V BR), respectively, deliverable by the power device. The developed model is utilized to obtain the optimal physical design space parameters for a comb-like power HEMT design. Due consideration has been given to the trade-off between R ds,on and area-specific R ds,on of the transistor, device processing limitations for all the physical device parameters. The developed model has been validated with experimental results of prior literature. Our calculations impose a lower-bound for the best possible R ds,on as well as the area-specific on-resistance product (R ds,on × AA) that can be obtained for a given starting channel sheet resistance in the comb architecture for a desired I ON − V DSO rating.
- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (11) , 5991-5995
Impact of ZnO Cap Layer on the Performance of MgZnO/CdZnO Heterostructure With YO Spacer Layer
In this work, we report the impact of the ZnO cap layer on mobility ($\mu $ ), sheet carrier density (${n} _{s}$ ), and conductance (${n} _{s} \times \mu $ ) of dual ion beam sputtering (DIBS) grown MgZnO/CdZnO (MCO) heterostructure with and without$\text{Y}_{{2}}\text{O}_{{3}}$ spacer layer. Hall measurements demonstrate that the addition of a 30-nm ZnO cap layer results in an enhancement of$\mu $ by about$2.3\times $ compared to that for the uncapped MCO heterostructure with a spacer layer. The results presented are significant for the realization of cost-effective and large area MCO-based heterostructure field-effect transistor (HFET) for sensor, microwave, and power devices.- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (11) , 5991-5995
Impact of ZnO Cap Layer on the Performance of MgZnO/CdZnO Heterostructure With YO Spacer Layer
In this work, we report the impact of the ZnO cap layer on mobility ($\mu $ ), sheet carrier density (${n} _{s}$ ), and conductance (${n} _{s} \times \mu $ ) of dual ion beam sputtering (DIBS) grown MgZnO/CdZnO (MCO) heterostructure with and without$\text{Y}_{{2}}\text{O}_{{3}}$ spacer layer. Hall measurements demonstrate that the addition of a 30-nm ZnO cap layer results in an enhancement of$\mu $ by about$2.3\times $ compared to that for the uncapped MCO heterostructure with a spacer layer. The results presented are significant for the realization of cost-effective and large area MCO-based heterostructure field-effect transistor (HFET) for sensor, microwave, and power devices.- 8 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (6) , 2276-2281
Drain Current Optimization in DIBS-Grown MgZnO/CdZnO HFET
This article reports the fabrication of a dual-ion beam sputtering (DIBS)-grown MgZnO/CdZnO (MCO)-based gateless heterostructure field-effect transistor (HFET). In addition, this article presents that by introducing a 30-nm yttria spacer layer, the crystallinity of the CdZnO buffer layer can be enhanced and the interface roughness at the heterojunction of the MCO heterostructure can be reduced. Furthermore, the source and drain metal contacts were optimized for the least specific contact resistivity (ρc) yielding metal combination and annealing conditions. The results suggest that the introduction of the yttria spacer layer improves the overall conductance [product of sheet carrier density (ns) and electron mobility (μ)] of MCO up to 3.5 x 10¹⁵ V⁻¹s⁻¹ compared to 9 x 10¹⁴ V⁻¹s⁻¹ in the non-yttria spacer-based MCO. In addition, the drain current (Id)-drain voltage (Vd) characteristic of the as-developed yttria spacer-based MCO HFET shows a high drain current value (~400 mA/mm). These results establish the DIBS-grown MCO heterostructure as a viable option for low-cost HFETs necessary for the fabrication of large-scale HFET-based power and sensor devices.
- 8 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (6) , 2276-2281
Drain Current Optimization in DIBS-Grown MgZnO/CdZnO HFET
This article reports the fabrication of a dual-ion beam sputtering (DIBS)-grown MgZnO/CdZnO (MCO)-based gateless heterostructure field-effect transistor (HFET). In addition, this article presents that by introducing a 30-nm yttria spacer layer, the crystallinity of the CdZnO buffer layer can be enhanced and the interface roughness at the heterojunction of the MCO heterostructure can be reduced. Furthermore, the source and drain metal contacts were optimized for the least specific contact resistivity (ρc) yielding metal combination and annealing conditions. The results suggest that the introduction of the yttria spacer layer improves the overall conductance [product of sheet carrier density (ns) and electron mobility (μ)] of MCO up to 3.5 x 10¹⁵ V⁻¹s⁻¹ compared to 9 x 10¹⁴ V⁻¹s⁻¹ in the non-yttria spacer-based MCO. In addition, the drain current (Id)-drain voltage (Vd) characteristic of the as-developed yttria spacer-based MCO HFET shows a high drain current value (~400 mA/mm). These results establish the DIBS-grown MCO heterostructure as a viable option for low-cost HFETs necessary for the fabrication of large-scale HFET-based power and sensor devices.
- 1 April 2020
- Published by Elsevier in Superlattices and Microstructures
- Vol. 140
Performance Analysis of p-LPZO/n-GZO and p-SZO/n-GZO Homojunction UV Photodetectors
- 1 April 2020
- Published by Elsevier in Superlattices and Microstructures
- Vol. 140
Performance Analysis of p-LPZO/n-GZO and p-SZO/n-GZO Homojunction UV Photodetectors