Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Min-Jae Seo has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 1.5-MHz BW 81.2-dB SNDR Dual-Residue Pipeline ADC With a Fully Dynamic Noise-Shaping Interpolating-SAR ADC

    by Jae-Hyun Chung, Ye-Dam Kim, Chang-Un Park, Kun-Woo Park, Dong-Ryeol Oh, Min-Jae Seo, Seung-Tak Ryu

    This article presents an energy-efficient high-resolution dual-residue (D-R) pipelined-successive approximation register (SAR) analog-to-digital converter (ADC), with a backend capacitive interpolating SAR ADC incorporated with noise-shaping (NS) capability. The residue amplifier design could be simplified as the residue is pre-amplified by the amplifier for the kT/ $C$ -noise cancellation. Moreover, the proposed segmented digital-to-analog converter (DAC) structure overcomes parasitic capacitance limitations in the capacitive interpolation, improving resolution along with the gain-error-free advantage of the D-R structure. Fabricated in a 180-nm CMOS technology, the prototype ADC achieves an 81.2-dB signal-to-noise and distortion ratio (SNDR) and an 89.9-dB spurious-free dynamic range (SFDR) in a 1.5-MHz bandwidth (BW) at an over-sampling ratio (OSR) of 8 with a 170.4-dB SNDR Schreier figure-of-merit (FoM) without any calibration.


  • A 7-Bit Two-Step Flash ADC With Sample-and-Hold Sharing Technique

    by Dong-Ryeol Oh, Min-Jae Seo, Seung-Tak Ryu

    A 7-bit 3 GS/s two-channel time-interleaved two-step flash analog-to-digital converter (ADC) with 7-GHz effective resolution bandwidth (ERBW) is presented. A reference-embedding flash ADC for a fine stage having only a single capacitive digital-to-analog converter improves the power efficiency and area efficiency as well as the input bandwidth. The proposed sample-and-hold sharing structure not only improves the input bandwidth by removing the effect of the input capacitance of the fine ADC (FADC) but also eliminates the gain error between the coarse ADC and the FADC. The advanced sequential slope-matching offset calibration technique in the eight-time interpolated FADC improves the gain of the voltage-to-time converter and the interpolation linearity. A prototype ADC implemented in a 40-nm CMOS process occupies 0.03 mm 2 , including offset calibration circuitry. The measured peak differential non-linearity (DNL) and integral non-linearity (INL) after calibration are 0.53 and 0.47 LSB, respectively. With a 1.49-GHz input, the measured signal-to-noise and distortion ratio (SNDR) and spurious-free dynamic range (SFDR) are 39.94 and 55.78 dB, respectively. The ERBW without and with time skew calibration is 4.8 and 7 GHz, respectively. The power consumption is 6.8 mW under a supply voltage of 0.9 V, leading to a figure of merit (FoM) of 28 fJ/conversion-step at 3 GS/s.


  • Open Access

    A Single-Amplifier Dual-Residue Pipelined-SAR ADC

    by Min-Jae Seo

    This work presents a 12 bit 200 MS/s dual-residue pipelined successive approximation registers (SAR) analog-to-digital converter (ADC) with a single open-loop residue amplifier (RA). By using the inherent characteristics of the SAR conversion scheme, the proposed ADC sequentially generates two residue levels from the single RA, which eliminates the need for inter-stage gain-matching calibration. To convert the sequentially generated the two residues, a capacitive interpolating SAR ADC (I-SAR ADC) is also proposed. The I-SAR ADC is very compact because it consists of the one comparator, a CDAC, and control logic like a conventional SAR ADC. In addition, the I-SAR ADC needs no static power dissipation for the residue interpolation. A prototype ADC fabricated in a 40 nm CMOS technology occupies an active area of 0.026 mm2. At a 200 MS/s sampling-rate with the Nyquist input, the ADC achieves an SNDR (Signal-to-Noise distortion ratio) of 62.1 dB and 67.1 dB SFDR (Spurious-Free Dynamic Range), respectively. The total power consumed is 3.9 mW under a 0.9 V supply. Without any inter-stage mismatch calibration, the ADC achieve Walden Figure-of-Merit (FoM) of 19.0 fJ/conversion-step.


  • A Single-Supply CDAC-Based Buffer-Embedding SAR ADC With Skip-Reset Scheme Having Inherent Chopping Capability

    by Min-Jae Seo, Dong-Hwan Jin, Ye-Dam Kim, Jong-Pal Kim, Seung-Tak Ryu

    This article presents a power-efficient buffer-embedding successive approximation register (SAR) analog-to-digital converter (ADC) that utilizes a core power supply for the source-follower buffer, having a rail-to-rail signal swing due to the capacitive-level shifting bias scheme. Also, to implement the switched-capacitor (SC) level-shifting bias scheme without bias leakage issue, a negative boosting circuit is proposed. The boosting circuit is designed without any reliability issue, even with the use of thin-oxide transistors. For low-power applications, such as the biomedical system and CMOS image sensor, the proposed ADC incorporates a skip-reset (SR) scheme, a low-power delta-readout method. In conjunction with 8x oversampling and the power-saving SR technique that has inherent chopping capability, a prototype SAR ADC fabricated in a 180-nm CMOS technology achieves a peak 74.8-dB signal-to-noise and distortion ratio (SNDR) and an 89.1-dB spurious free dynamic range (SFDR) for a 640-kHz bandwidth (BW) with an oversampling ratio (OSR) of 8, resulting in a Schreier figure of merit (FoM) of 167.3 dB. The chip area occupies 0.192 mm², and the power consumption is 180.1 μW.


  • A 40-nm CMOS 7-b 32-GS/s SAR ADC With Background Channel Mismatch Calibration

    by Dong-Shin Jo, Ba-Ro-Saim Sung, Min-Jae Seo, Woo-Cheol Kim, Seung-Tak Ryu

    This brief presents a 7-b 32-GS/s successive approximation register analog-to-digital converter (ADC) using a massive time-interleaving (TI) architecture. For low-skew multi-phase clocks, generation utilizing a delay-locked loop (DLL) phase-detector (PD) with a reduced offset is proposed to minimize skew between the clocks. Different clock path delays caused by distributed sub-ADCs over a large area in a massive TI-ADC are compensated for by multiplexing master clocks from the DLL. Offsets and skews in the sub-channels are calibrated on chip in the background via an additional dedicated sub-channel. A prototype chip was implemented in a 40-nm CMOS process with an active area of 0.36 mm 2 . The measured SFDR and SNDR of the prototype ADC at a conversion rate of 32 GS/s are 43.1 and 31.4 dB, respectively. The ADC, including the input buffers, consumes 125 mW under a single 0.9-V supply.


  • A Reference-Free Temperature-Dependency-Compensating Readout Scheme for Phase-Change Memory Using Flash-ADC-Configured Sense Amplifiers

    by Dong-Hwan Jin, Ji-Wook Kwon, Min-Jae Seo, Mi-Young Kim, Min-Chul Shin, Seok-Joon Kang, Jung-Hyuk Yoon, Taek-Seung Kim, Seung-Tak Ryu


  • A 18.5 nW 12-bit 1-kS/s Reset-Energy Saving SAR ADC for Bio-Signal Acquisition in 0.18-μm CMOS

    by Min-Jae Seo, Dong-Hwan Jin, Ye-Dam Kim, Sun-Il Hwang, Jong-Pal Kim, Seung-Tak Ryu

    This paper presents three low-power design techniques for successive approximation registers (SAR) analog-to-digital converter (ADC) for bio-potential signal acquisition: skip-reset, delta (Δ) readout with MSB-rounding, and tri-level split monotonic switching. The skip-reset scheme reduces not only reference energy but also digital switching energy for the ADC reset. The Δ-readout process with the proposed MSB-rounding technique shifts the location of the resolvable range using the previous digital code to increase the hit-rate. Finally, the tri-level split monotonic switching scheme minimizes the CDAC switching activity in predictive residue generation for the Δ-readout process. A prototype ADC was fabricated in a 0.18-μm CMOS technology and occupies an active area of 0.17 mm 2 . At a 1.5-V supply voltage and a 1-kS/s sampling-rate with the electrocardiogram signal input, the ADC power consumption could be reduced to 18.5 nW, corresponding to 71% power saving, and owing to the proposed techniques from a conventional SAR ADC consuming 63.5 nW.


  • A Reusable Code-Based SAR ADC Design With CDAC Compiler and Synthesizable Analog Building Blocks

    by Min-Jae Seo, Yi-Ju Roh, Dong-Jin Chang, Wan Kim, Ye-Dam Kim, Seung-Tak Ryu

    This brief proposes a code-reusable design methodology for synthesizable successive approximation register (SAR) ADCs based on the digital design flow to significantly reduce design effort. The SAR ADCs are composed of a capacitor-DAC (CDAC) macro cell generated by a CDAC compiler and analog functional blocks implemented utilizing digital standard cells. Two prototypes of SAR ADCs (12-bit 100 kS/s and 11-bit 50 MS/s) are fabricated in different CMOS processes (180 nm and 28 nm). The prototype ADCs prove the effectiveness of the proposed design methodology with comparable performances with full-custom designed SAR ADCs.


  • A 2.7-M Pixels 64-mW CMOS Image Sensor With Multicolumn-Parallel Noise-Shaping SAR ADCs

    by Sun-Il Hwang, Jae-Hyun Chung, Hyeon-June Kim, Il-Hoon Jang, Min-Jae Seo, Sang-Hyun Cho, Heewon Kang, Minho Kwon, Seung-Tak Ryu

    This paper presents a CMOS image sensor (CIS) utilizing a noise-shaping successive-approximation register analog-to-digital converter (SAR ADC) incorporating the delta-readout scheme. While the noise-shaping SAR ADC with a proposed two-tap passive finite-impulse response (FIR) filter improves effective resolution, the delta-readout scheme reduces its power consumption. A prototype 1920 × 1440 pixel CIS was fabricated in a 90-nm CIS process. A single-channel readout SAR ADC occupying an area of 22.4 μm × 715 μm was implemented for reading out 16 columns of pixel array, consuming 437 μW. Owing to the proposed noise-shaping SAR ADC with oversampling ratio of 16, this paper achieves a noise reduction of 14 dB compared with the noise of a conventional SAR ADC. The delta-readout reduces the power consumption of the SAR ADC by 10% due to the high hit rate of the full high definition image format. The measured differential nonlinearity of the ADC is +0.77/-0.54 LSB and the integral nonlinearity is +0.81/-0.5 LSB. The prototype CIS consumes a total power of 64 mW and achieves a dynamic range of 66.5 dB and a figure of merit of 127 μV·nJ at a data rate of 138 Mpixels/s.


  • A 4.2-mW 10-MHz BW 74.4-dB SNDR Continuous-Time Delta-Sigma Modulator With SAR-Assisted Digital-Domain Noise Coupling

    by Il-Hoon Jang, Min-Jae Seo, Sang-Hyun Cho, Jae-Keun Lee, Seung-Yeob Baek, Sunwoo Kwon, Michael Choi, Hyung-Jong Ko, Seung-Tak Ryu

    This paper introduces a high-order continuous-time (CT) delta-sigma modulator (DSM) that applies digital-domain noise coupling (DNC) based on the structural advantages of the successive-approximation register (SAR) analog-to-digital converter (ADC), which makes the implementation of second-order noise coupling very simple. Due to digital-domain implementation as well as the SAR ADC where the key building blocks are embedded for the proposed DNC, compact size and efficient power consumption could be designed. For low circuit noise, a feedback DAC is implemented with a tri-level current-steering DAC. Tri-level data-weight averaging (TDWA) improves the linearity of the DAC. With the proposed DNC and TDWA, a prototype CT DSM fabricated in a 28-nm CMOS achieves a peak 74.4-dB SNDR and an 80.8-dB dynamic range (DR) for a 10-MHz BW with an oversampling ratio of 16, resulting in a Schreier FoM DR of 174.5 dB. The chip area occupies 0.1 mm 2 , and the power consumption is 4.2 mW.