Mark G. van der Krogt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mark G. van der Krogt has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Timo Schweckendiek
Deltares
3 shared publications Katerina Rippi
Unit Geo-Engineering
2 shared publications- Timo Schweckendiek
Faculty of Civil Engineering and Geosciences, Delft University of Technology, Delft, The Netherlands
2 shared publications Ana Teixeira
Unit Geo-Engineering
1 shared publication- Ana Teixeira
Deltares
1 shared publication - Bianca Hardeman
Deltares
1 shared publication
Latest Publications
- 1 January 2022
- Published by Research Publishing Services
- p. 930-935
Time-Dependent Reliability Analysis of an Existing Sheet Pile Wall Case Study
- 1 January 2022
- Published by Research Publishing Services
- p. 930-935
Time-Dependent Reliability Analysis of an Existing Sheet Pile Wall Case Study
- Open Access
- 18 December 2020
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 18 (4) , 505-520
Value of information of combinations of proof loading and pore pressure monitoring for flood defences
Spatial variability and limited measurements often result in low reliability estimates of geotechnical failure modes of dikes (i.e., earthen flood defences). Required dike reinforcements are usually not executed within a few years after inception, which enables efforts to improve reliability estimates by reducing uncertainty. Often decision makers are unclear on whether uncertainty reduction is worth investing, and which (combination of) methods yields the highest Value of Information (VoI). This paper presents a framework to assess the VoI of two uncertainty reduction methods (proof loading and pore pressure monitoring) for a case study of a typical river dike with an insufficiently stable inner slope, using a decision tree. In all cases, a positive VoI was found for at least one strategy consisting of a proof load test, monitoring or both. The optimal strategy of proof loading and monitoring has a VoI of 4.0 M€, being a reduction in total cost of 25% compared to a conventional dike reinforcement. It was also found that sometimes proof loading enhances the VoI of pore pressure monitoring, which demonstrates the benefits of jointly considering different methods in a single decision tree. The decision framework yields insight in total cost and VoI of risk reduction strategies, which enables decision makers to determine where proof loading and/or pore pressure monitoring are efficient, leading to more efficient flood defence asset management.
- 18 December 2020
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 18 (4) , 505-520
Open AccessValue of information of combinations of proof loading and pore pressure monitoring for flood defences
Spatial variability and limited measurements often result in low reliability estimates of geotechnical failure modes of dikes (i.e., earthen flood defences). Required dike reinforcements are usually not executed within a few years after inception, which enables efforts to improve reliability estimates by reducing uncertainty. Often decision makers are unclear on whether uncertainty reduction is worth investing, and which (combination of) methods yields the highest Value of Information (VoI). This paper presents a framework to assess the VoI of two uncertainty reduction methods (proof loading and pore pressure monitoring) for a case study of a typical river dike with an insufficiently stable inner slope, using a decision tree. In all cases, a positive VoI was found for at least one strategy consisting of a proof load test, monitoring or both. The optimal strategy of proof loading and monitoring has a VoI of 4.0 M€, being a reduction in total cost of 25% compared to a conventional dike reinforcement. It was also found that sometimes proof loading enhances the VoI of pore pressure monitoring, which demonstrates the benefits of jointly considering different methods in a single decision tree. The decision framework yields insight in total cost and VoI of risk reduction strategies, which enables decision makers to determine where proof loading and/or pore pressure monitoring are efficient, leading to more efficient flood defence asset management.
- 1 January 2019
- Published by Research Publishing Services
Systematic Transformation Error in the Depth-Average Undrained Shear Strength
- 1 January 2019
- Published by Research Publishing Services
Systematic Transformation Error in the Depth-Average Undrained Shear Strength
- Open Access
- 11 December 2018
- Published by Taylor & Francis in Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards
- Vol. 13 (3) , 226-236
Uncertainty in spatial average undrained shear strength with a site-specific transformation model
Transformation models are used to infer geotechnical properties from indirect measurements. A site-specific transformation model can be calibrated with direct and indirect measurements from a site. When such a model is used, then spatial variability, measurement errors and statistical uncertainty propagate into the uncertainty of the spatial average, which is the variable of interest in most geotechnical analyses. This research shows how all components enter the total uncertainty of a transformation model for undrained shear strength from cone resistance. A method is proposed to estimate the uncertainty in the spatial average undrained shear strength, particularly focusing on the role of averaging of all spatially variable error components. The main finding is that if a considerable share of the measurement and transformation errors is random or spatially variable, the uncertainty estimates can be considerably lower compared to methods proposed earlier, and hence, characteristic values can be considerably higher.
- 11 December 2018
- Published by Taylor & Francis in Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards
- Vol. 13 (3) , 226-236
Open AccessUncertainty in spatial average undrained shear strength with a site-specific transformation model
Transformation models are used to infer geotechnical properties from indirect measurements. A site-specific transformation model can be calibrated with direct and indirect measurements from a site. When such a model is used, then spatial variability, measurement errors and statistical uncertainty propagate into the uncertainty of the spatial average, which is the variable of interest in most geotechnical analyses. This research shows how all components enter the total uncertainty of a transformation model for undrained shear strength from cone resistance. A method is proposed to estimate the uncertainty in the spatial average undrained shear strength, particularly focusing on the role of averaging of all spatially variable error components. The main finding is that if a considerable share of the measurement and transformation errors is random or spatially variable, the uncertainty estimates can be considerably lower compared to methods proposed earlier, and hence, characteristic values can be considerably higher.
- 1 June 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 494-503
Reliability Updating with Survival Information for Dike Slope Stability Using Fragility Curves
Dikes and levees play a crucial role in flood protection. The main causes of levee failures are of geotechnical nature. Geotechnical failure modes are also the main contributors to the probability of failure of flood defenses such as levees due to the large uncertainties in ground conditions. Hence, information on ground conditions and soil properties is crucial in safety assessments and retrofitting designs of levees. The experience in practice with designs and risk assessments is that even with a substantial amount of site investigation and laboratory testing the uncertainties in soil properties often remain large. One way to further reduce uncertainties is to include past performance information. The present papers shows how information of survived loads in the past can be incorporated in reliability assessments by means of Bayesian posterior analysis using the same (physics-based) performance models as the prior reliability assessments. The incorporation of survival information leads to reduced uncertainties and probabilities of failure. Furthermore, an approximate approach using fragility curves is proposed, mainly to make problems with computationally expensive performance functions tractable. After briefly recapping Bayesian reliability updating, we provide examples for slope stability of (flood protection) dikes. The examples illustrate that posterior analysis enables us to reduce the large prior uncertainties in soil strength parameters by “eliminating” implausible samples or regions of the joint PDF of the strength properties using the evidence of survived load conditions (i.e. water levels). The results suggest that the effect of updating the probability of failure with survival evidence can be considerable, especially when the uncertainty in the strength properties dominates the reliability. Dominant strength uncertainties are rather typical in geotechnical engineering, as opposed to, for example, structural engineering, implying that using the method is promising also for other geotechnical applications.
- 1 June 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 494-503
Reliability Updating with Survival Information for Dike Slope Stability Using Fragility Curves
Dikes and levees play a crucial role in flood protection. The main causes of levee failures are of geotechnical nature. Geotechnical failure modes are also the main contributors to the probability of failure of flood defenses such as levees due to the large uncertainties in ground conditions. Hence, information on ground conditions and soil properties is crucial in safety assessments and retrofitting designs of levees. The experience in practice with designs and risk assessments is that even with a substantial amount of site investigation and laboratory testing the uncertainties in soil properties often remain large. One way to further reduce uncertainties is to include past performance information. The present papers shows how information of survived loads in the past can be incorporated in reliability assessments by means of Bayesian posterior analysis using the same (physics-based) performance models as the prior reliability assessments. The incorporation of survival information leads to reduced uncertainties and probabilities of failure. Furthermore, an approximate approach using fragility curves is proposed, mainly to make problems with computationally expensive performance functions tractable. After briefly recapping Bayesian reliability updating, we provide examples for slope stability of (flood protection) dikes. The examples illustrate that posterior analysis enables us to reduce the large prior uncertainties in soil strength parameters by “eliminating” implausible samples or regions of the joint PDF of the strength properties using the evidence of survived load conditions (i.e. water levels). The results suggest that the effect of updating the probability of failure with survival evidence can be considerable, especially when the uncertainty in the strength properties dominates the reliability. Dominant strength uncertainties are rather typical in geotechnical engineering, as opposed to, for example, structural engineering, implying that using the method is promising also for other geotechnical applications.
- 1 June 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Calibration of Factors of Safety for Slope Stability of Dikes
Dikes in the Netherlands are by law required to comply with predefined safety standards. The goal of this paper is to derive the safety format and the required factor of safety for the inner slope (landside slope) instability failure mode. The first step is to derive the required target reliability for a cross-section. The second step is to derive a safety format in which all uncertain variables in the slope stability computation are identified and accounted for by sufficiently safe parameters estimates. The third step is to derive the relation between target reliability and required factor of safety. This is done by evaluating 48 test cases. For each test case, the factor of safety is computed based on the safety format, as well the corresponding reliability index. This paper shows how to derive a required factor of safety based on a predefined target reliability. However, the spread in this relationship is significant. Hence, a full probabilistic analysis would lead to more accurate slope stability assessments.
- 1 June 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Calibration of Factors of Safety for Slope Stability of Dikes
Dikes in the Netherlands are by law required to comply with predefined safety standards. The goal of this paper is to derive the safety format and the required factor of safety for the inner slope (landside slope) instability failure mode. The first step is to derive the required target reliability for a cross-section. The second step is to derive a safety format in which all uncertain variables in the slope stability computation are identified and accounted for by sufficiently safe parameters estimates. The third step is to derive the relation between target reliability and required factor of safety. This is done by evaluating 48 test cases. For each test case, the factor of safety is computed based on the safety format, as well the corresponding reliability index. This paper shows how to derive a required factor of safety based on a predefined target reliability. However, the spread in this relationship is significant. Hence, a full probabilistic analysis would lead to more accurate slope stability assessments.