Bhaskara Rupakula
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bhaskara Rupakula has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Gabriel M. Rebeiz
Electrical and Computer Engineering Department, University of California at San Diego, La Jolla, CA, USA
8 shared publicationsSamet Zihir
3 shared publications- Abdurrahman H. Aljuhani
Department of Electrical and Computer Engineering, University of California, San Diego, CA, USA
2 shared publications - Siwei Li
Department of Electrical and Computer Engineering, University of California, San Diego, CA, USA
2 shared publications - Zhe Zhang
Department of Electrical and Computer Engineering, University of California at San Diego, La Jolla, CA, USA
2 shared publications Abdurrahman H. Aljuhani
1 shared publication
Latest Publications
- Top Cited Papers
- 12 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (2) , 385-399
An Eight-Element 140-GHz Wafer-Scale IF Beamforming Phased-Array Receiver With 64-QAM Operation in CMOS RFSOI
This article presents a 140-GHz eight-element wafer-scale phased-array receiver based on intermediate-frequency (IF) beamforming with 5-bit phase and 4-bit gain control. The chip contains a shared local-oscillator (LO) multiplier chain and distribution network, active combiners,$LC$ -based combiners, digitally tuned attenuators, for a near system-on-chip solution. A differential on-chip antenna feed (on the top metal) is electromagnetically (EM) coupled to a high-efficiency patch antenna (gold) on a 100-$\mu \text{m}$ -thick quartz superstrate, and placed$\lambda $ /2 (~140 GHz) apart in the horizontal and vertical directions. The$4\times 2$ -element phased-array chip with attached quartz superstrate is wire-bonded to a printed circuit board containing IF and LO ports, and scans to ±35° in the elevation plane ($E$ -plane). The measured channel NF is 7 dB and the array electronic gain is 27–28 dB with an RF front-end 3-dB bandwidth of 139–155 GHz and an IF bandwidth of 9.5–12.5 GHz. To evaluate the over-the-air performance, a communication link is demonstrated with 16-quadrature amplitude modulation (QAM) and 64-QAM waveforms, realizing up to 9–10-Gb/s data rates. To the best of our knowledge, this article presents the first CMOS wafer-scale phased-array receiver at 140 GHz with a low system noise figure and high data rate.- 12 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (2) , 385-399
Top Cited PapersAn Eight-Element 140-GHz Wafer-Scale IF Beamforming Phased-Array Receiver With 64-QAM Operation in CMOS RFSOI
This article presents a 140-GHz eight-element wafer-scale phased-array receiver based on intermediate-frequency (IF) beamforming with 5-bit phase and 4-bit gain control. The chip contains a shared local-oscillator (LO) multiplier chain and distribution network, active combiners,$LC$ -based combiners, digitally tuned attenuators, for a near system-on-chip solution. A differential on-chip antenna feed (on the top metal) is electromagnetically (EM) coupled to a high-efficiency patch antenna (gold) on a 100-$\mu \text{m}$ -thick quartz superstrate, and placed$\lambda $ /2 (~140 GHz) apart in the horizontal and vertical directions. The$4\times 2$ -element phased-array chip with attached quartz superstrate is wire-bonded to a printed circuit board containing IF and LO ports, and scans to ±35° in the elevation plane ($E$ -plane). The measured channel NF is 7 dB and the array electronic gain is 27–28 dB with an RF front-end 3-dB bandwidth of 139–155 GHz and an IF bandwidth of 9.5–12.5 GHz. To evaluate the over-the-air performance, a communication link is demonstrated with 16-quadrature amplitude modulation (QAM) and 64-QAM waveforms, realizing up to 9–10-Gb/s data rates. To the best of our knowledge, this article presents the first CMOS wafer-scale phased-array receiver at 140 GHz with a low system noise figure and high data rate. - 7 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 795-798
An Eight-Element 140 GHz Wafer-Scale Phased-Array Transmitter with 32 dBm Peak EIRP and > 16 Gbps 16QAM and 64QAM Operation
This paper presents an 8-element 140 GHz wafer-scale phased-array transmitter in CMOS. It is based on intermediate-frequency (IF) beamforming transmit channels with 5-bit phase and 4-bit gain control at the IF band (9–14 GHz) with LC-based Wilkinson combiners, a shared local-oscillator (LO) multiplier chain and distribution network. On-chip image rejection filters (IRF) and LO leakage cancellation circuits are designed in each channel to improve the array in-band linearity and suppress the LO leakage. Differential on-chip antenna feeds (on top metal) are electromagnetically (EM) coupled to high-efficiency patch antennas on a 100-µm-thick quartz superstrate. The antennas are placed λ/2 (~140 GHz) apart between adjacent channels in the horizontal and vertical directions with a chip size of 5.4 mm × 5.1 mm. The 4 × 2-element array can scan to ±30° in the elevation plane (E-plane). The phased-array transmitter results in a measured EIRP of 27–32 dBm at 134–146 GHz. It supports up to 16 Gb/s data rate per carrier for both 16 and 64QAM waveforms at an EIRP of 22 and 20 dBm, repectively, with −25 dBc EVM (for 64QAM). To the best of our knowledge, this paper presents the first CMOS wafer-scale phased-array transmitter at 140 GHz, resulting in high radiated power and high speed communications.
- 7 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 795-798
An Eight-Element 140 GHz Wafer-Scale Phased-Array Transmitter with 32 dBm Peak EIRP and > 16 Gbps 16QAM and 64QAM Operation
This paper presents an 8-element 140 GHz wafer-scale phased-array transmitter in CMOS. It is based on intermediate-frequency (IF) beamforming transmit channels with 5-bit phase and 4-bit gain control at the IF band (9–14 GHz) with LC-based Wilkinson combiners, a shared local-oscillator (LO) multiplier chain and distribution network. On-chip image rejection filters (IRF) and LO leakage cancellation circuits are designed in each channel to improve the array in-band linearity and suppress the LO leakage. Differential on-chip antenna feeds (on top metal) are electromagnetically (EM) coupled to high-efficiency patch antennas on a 100-µm-thick quartz superstrate. The antennas are placed λ/2 (~140 GHz) apart between adjacent channels in the horizontal and vertical directions with a chip size of 5.4 mm × 5.1 mm. The 4 × 2-element array can scan to ±30° in the elevation plane (E-plane). The phased-array transmitter results in a measured EIRP of 27–32 dBm at 134–146 GHz. It supports up to 16 Gb/s data rate per carrier for both 16 and 64QAM waveforms at an EIRP of 22 and 20 dBm, repectively, with −25 dBc EVM (for 64QAM). To the best of our knowledge, this paper presents the first CMOS wafer-scale phased-array transmitter at 140 GHz, resulting in high radiated power and high speed communications.
- 4 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (12) , 5268-5281
Low Complexity 54–63-GHz Transmit/Receive 64- and 128-element 2-D-Scanning Phased-Arrays on Multilayer Organic Substrates With 64-QAM 30-Gbps Data Rates
This article presents 64- and 128-element transmit/receive phased-arrays built using SiGe 2 x 2 quad-chips flipped on a multilayer organic printed-circuit board (PCB). The arrays cover 54-63 GHz with 40-45-dBm effective isotropic radiated power (EIRP) in the TX mode. The antenna elements are stacked microstrip antennas spaced at 0.5λ in the horizontal plane and 0.7λ in the vertical plane at 60 GHz, resulting in a scan range of ±50° in azimuth and ±15° in elevation. A 64-QAM 30-Gbps communication link is achieved in the transmit mode when using its full instantaneous bandwidth. This article shows that it is possible to build phased-arrays at 60 GHz and beyond using simple 2 x 2 quad-chips with low antenna distribution loss, and not using complex chips with 16-32 antenna connections and high distribution loss. Applications include high data-rate point-to-multipoint links, reconfigurable mesh networks, and automotive radars.
- 4 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (12) , 5268-5281
Low Complexity 54–63-GHz Transmit/Receive 64- and 128-element 2-D-Scanning Phased-Arrays on Multilayer Organic Substrates With 64-QAM 30-Gbps Data Rates
This article presents 64- and 128-element transmit/receive phased-arrays built using SiGe 2 x 2 quad-chips flipped on a multilayer organic printed-circuit board (PCB). The arrays cover 54-63 GHz with 40-45-dBm effective isotropic radiated power (EIRP) in the TX mode. The antenna elements are stacked microstrip antennas spaced at 0.5λ in the horizontal plane and 0.7λ in the vertical plane at 60 GHz, resulting in a scan range of ±50° in azimuth and ±15° in elevation. A 64-QAM 30-Gbps communication link is achieved in the transmit mode when using its full instantaneous bandwidth. This article shows that it is possible to build phased-arrays at 60 GHz and beyond using simple 2 x 2 quad-chips with low antenna distribution loss, and not using complex chips with 16-32 antenna connections and high distribution loss. Applications include high data-rate point-to-multipoint links, reconfigurable mesh networks, and automotive radars.
- 22 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (3) , 1045-1053
ACPR Improvement in Large Phased Arrays With Complex Modulated Waveforms
- 22 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (3) , 1045-1053
ACPR Improvement in Large Phased Arrays With Complex Modulated Waveforms
- 19 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (1) , 70-80
Limited Scan-Angle Phased Arrays Using Randomly Grouped Subarrays and Reduced Number of Phase Shifters
This paper presents randomly-grouped subarray techniques to reduce the number of phase-shifters in a twodimensional (2-D) phased-array while maintaining a certain scan range in the azimuth and elevation planes and keeping sidelobes below a specified level. It is shown that controlling random groups of elements in such a manner suppresses these grating lobes and allows the use of fewer phase-shifters. Guidelines for finding the best partition of a phased-array into random subgroups are presented. It is shown that 75% reduction in phase-shifters can be achieved while maintaining a 40° scan range in the azimuth plane, 15° scan range in the elevation plane and keeping -10 to -12 dB sidelobes without tapering and with 6 dB taper. Other partitions are also presented with up to 88% reduction in phase-shifters while maintaining a 5° scan range in elevation. Measurements on a 16x16 2-D phased-array at 14 GHz are used to confirm the performance of randomly partitioned phased-arrays. Application areas are in arrays with limited scan-angle in the elevation plane, such as automotive radars, aircraft landing systems, and pointto-point communication systems.
- 19 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (1) , 70-80
Limited Scan-Angle Phased Arrays Using Randomly Grouped Subarrays and Reduced Number of Phase Shifters
This paper presents randomly-grouped subarray techniques to reduce the number of phase-shifters in a twodimensional (2-D) phased-array while maintaining a certain scan range in the azimuth and elevation planes and keeping sidelobes below a specified level. It is shown that controlling random groups of elements in such a manner suppresses these grating lobes and allows the use of fewer phase-shifters. Guidelines for finding the best partition of a phased-array into random subgroups are presented. It is shown that 75% reduction in phase-shifters can be achieved while maintaining a 40° scan range in the azimuth plane, 15° scan range in the elevation plane and keeping -10 to -12 dB sidelobes without tapering and with 6 dB taper. Other partitions are also presented with up to 88% reduction in phase-shifters while maintaining a 5° scan range in elevation. Measurements on a 16x16 2-D phased-array at 14 GHz are used to confirm the performance of randomly partitioned phased-arrays. Application areas are in arrays with limited scan-angle in the elevation plane, such as automotive radars, aircraft landing systems, and pointto-point communication systems.
- 24 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5780-5795
Third-Order Intermodulation Effects and System Sensitivity Degradation in Receive-Mode 5G Phased Arrays in the Presence of Multiple Interferers
Electronically scanned phased-array antennas need to function in an interference-rich environment as an integral part of millimeter-wave 5G networks. In these scenarios, multiple interferers' incident from different directions can create intermodulation products that can severely degrade the system sensitivity. This paper first presents the theoretical analysis of intermodulation effects in a receive-mode phased array and then shows the detailed experimental verification of multiple interferer effects on a 28-GHz 5G phased array. It is shown that the third-order intermodulation products generated by the interferers peak at certain predictable scan angles depending on the interferer directions of arrival and can limit the sensitivity of the phased array. The interferers degrade the system sensitivity even if incident in the direction of pattern nulls. Two scan-angle-dependent third-order input intercept point (IIP3) definitions are given for a phased array and their implications are discussed. It is shown that while a phased array does result in an input P1dB improvement as the number of elements increases (handles more incident power than a single channel), it does not result in an IIP3 improvement over a single channel as the number of elements increases. Theoretical predictions are also verified by extensive numerical simulations and measurement results for multiple interferers from different directions. Finally, the IIP3 degradation in mechanically scanned antennas is analyzed and it is shown that such antennas are much more robust than phased arrays for wide angle interferers.
- 24 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (12) , 5780-5795
Third-Order Intermodulation Effects and System Sensitivity Degradation in Receive-Mode 5G Phased Arrays in the Presence of Multiple Interferers
Electronically scanned phased-array antennas need to function in an interference-rich environment as an integral part of millimeter-wave 5G networks. In these scenarios, multiple interferers' incident from different directions can create intermodulation products that can severely degrade the system sensitivity. This paper first presents the theoretical analysis of intermodulation effects in a receive-mode phased array and then shows the detailed experimental verification of multiple interferer effects on a 28-GHz 5G phased array. It is shown that the third-order intermodulation products generated by the interferers peak at certain predictable scan angles depending on the interferer directions of arrival and can limit the sensitivity of the phased array. The interferers degrade the system sensitivity even if incident in the direction of pattern nulls. Two scan-angle-dependent third-order input intercept point (IIP3) definitions are given for a phased array and their implications are discussed. It is shown that while a phased array does result in an input P1dB improvement as the number of elements increases (handles more incident power than a single channel), it does not result in an IIP3 improvement over a single channel as the number of elements increases. Theoretical predictions are also verified by extensive numerical simulations and measurement results for multiple interferers from different directions. Finally, the IIP3 degradation in mechanically scanned antennas is analyzed and it is shown that such antennas are much more robust than phased arrays for wide angle interferers.
- 6 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (9) , 4108-4120
63.5–65.5-GHz Transmit/Receive Phased-Array Communication Link With 0.5–2 Gb/s at 100–800 m and ± 50° Scan Angles
This paper presents a 32-element phased array centered at 64 GHz using multiple SiGe chips on a single printed-circuit board. The antenna element is a series-fed patch array, which provides directivity in the elevation plane. The transmit array results in an effective isotropic radiated power of 42±2 dBm at 63-65.5 GHz, while the receive array provides an electronic gain of 24 dB and a system noise figure <7.7 dB, including antenna loss, T/R switch, beamformer, and transceiver. The arrays can be scanned to ±50° in the azimuth using a 5-bit phase shifter on the SiGe chip without degradation in sidelobes and maintaining a near-ideal pattern. A communication link between two phased arrays at 100, 300, and 800 m is also demonstrated, and employs one array on the transmit side and another array on the receive side, together with external mixers and IF amplifiers. The link performance was measured for different scan angles and modulation formats. Data rates of 0.5-2 Gb/s using 16-QAM and QPSK waveforms are demonstrated at 100-800 m, with 2-Gb/s data rate at 300 m and ~500-Mb/s data rate at 800 m. To the best of our knowledge, this is the first system-level demonstration of a silicon-based Gb/s 60-GHz phased array over hundreds of meters. Application areas are in point-to-multipoint links, back-haul and front-haul links, and reconfigurable mesh networks for advanced communication systems.
- 6 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (9) , 4108-4120
63.5–65.5-GHz Transmit/Receive Phased-Array Communication Link With 0.5–2 Gb/s at 100–800 m and ± 50° Scan Angles
This paper presents a 32-element phased array centered at 64 GHz using multiple SiGe chips on a single printed-circuit board. The antenna element is a series-fed patch array, which provides directivity in the elevation plane. The transmit array results in an effective isotropic radiated power of 42±2 dBm at 63-65.5 GHz, while the receive array provides an electronic gain of 24 dB and a system noise figure <7.7 dB, including antenna loss, T/R switch, beamformer, and transceiver. The arrays can be scanned to ±50° in the azimuth using a 5-bit phase shifter on the SiGe chip without degradation in sidelobes and maintaining a near-ideal pattern. A communication link between two phased arrays at 100, 300, and 800 m is also demonstrated, and employs one array on the transmit side and another array on the receive side, together with external mixers and IF amplifiers. The link performance was measured for different scan angles and modulation formats. Data rates of 0.5-2 Gb/s using 16-QAM and QPSK waveforms are demonstrated at 100-800 m, with 2-Gb/s data rate at 300 m and ~500-Mb/s data rate at 800 m. To the best of our knowledge, this is the first system-level demonstration of a silicon-based Gb/s 60-GHz phased array over hundreds of meters. Application areas are in point-to-multipoint links, back-haul and front-haul links, and reconfigurable mesh networks for advanced communication systems.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 787-790
Intermodulation Effects and System Sensitivity Degradation in $5\mathrm{G}$ Phased-Arrays due to Multiple InterferersElectronically-scanned phased arrays are an integral part of millimeter-wave 5G networks, and therefore, it is important to examine the effects of interferers on the performance of a receiving phased-array. This paper presents both theoretical analysis and experimental verification of 1M3 effects in a 28 GHz 5G phased array operating in the receive mode. It is shown that the intermodulation products generated by interferers peak at certain predictable scan angles depending on their direction of arrival and can limit the sensitivity of the phased array. The interferers degrade the phased-array sensitivity even if present in the direction of pattern nulls. Theoretical predictions are verified by numerical code and measurement results for multiple interferers from different directions.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 787-790
Intermodulation Effects and System Sensitivity Degradation in $5\mathrm{G}$ Phased-Arrays due to Multiple InterferersElectronically-scanned phased arrays are an integral part of millimeter-wave 5G networks, and therefore, it is important to examine the effects of interferers on the performance of a receiving phased-array. This paper presents both theoretical analysis and experimental verification of 1M3 effects in a 28 GHz 5G phased array operating in the receive mode. It is shown that the intermodulation products generated by interferers peak at certain predictable scan angles depending on their direction of arrival and can limit the sensitivity of the phased array. The interferers degrade the phased-array sensitivity even if present in the direction of pattern nulls. Theoretical predictions are verified by numerical code and measurement results for multiple interferers from different directions.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 791-793
Linearity and Efficiency Improvements in Phased-Array Transmitters with Large Number of Elements and Complex Modulation
Phased array transmit systems use several antennas to combine RF power-amplifiers in free space. If all the RF channels are identical, then the transmit spectrum in the far-field, including both linear and nonlinear components, would be a scaled version of the output spectrum of each channel. However, random variations in the nonlinear components (AM-AM and AM-PM conversion) between the channels improves the nonlinearity of the overall array as the number of elements increases. In this paper, measured results are used to show that the adjacent channel power ratio, which is one metric of linearity, improves with the number of elements at a fixed backoff from the 1 dB compression point. Also, for a 100 Mbaud 64QAM signal and a fixed ACPR of -32 dBc, a 256-element phased-array can be operated at P1dB-2dB, while an 8-element phased-array would need to be operated at P1dB-4dB for the same ACPR level. This work has great implications on the overall efficiency of 5G phased arrays since it implies that large phased-arrays can be operated at less back-off than small phased-arrays (or single antennas with high power amplifiers). Thus, in reality and taking the ACPR as the figure of merit, phased-arrays are 2 dB more efficient than what is predicted by standard system simulations which assume the same non-linear response for all the phased-array channels.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 791-793
Linearity and Efficiency Improvements in Phased-Array Transmitters with Large Number of Elements and Complex Modulation
Phased array transmit systems use several antennas to combine RF power-amplifiers in free space. If all the RF channels are identical, then the transmit spectrum in the far-field, including both linear and nonlinear components, would be a scaled version of the output spectrum of each channel. However, random variations in the nonlinear components (AM-AM and AM-PM conversion) between the channels improves the nonlinearity of the overall array as the number of elements increases. In this paper, measured results are used to show that the adjacent channel power ratio, which is one metric of linearity, improves with the number of elements at a fixed backoff from the 1 dB compression point. Also, for a 100 Mbaud 64QAM signal and a fixed ACPR of -32 dBc, a 256-element phased-array can be operated at P1dB-2dB, while an 8-element phased-array would need to be operated at P1dB-4dB for the same ACPR level. This work has great implications on the overall efficiency of 5G phased arrays since it implies that large phased-arrays can be operated at less back-off than small phased-arrays (or single antennas with high power amplifiers). Thus, in reality and taking the ACPR as the figure of merit, phased-arrays are 2 dB more efficient than what is predicted by standard system simulations which assume the same non-linear response for all the phased-array channels.