Esteban Bernal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Esteban Bernal has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Colin Cole
13 shared publicationsMaksym Spiryagin
11 shared publications- Qing Wu
CQUniversity
11 shared publications - Maksym Spiryagin
Central Queensland University, Centre for Railway Engineering
8 shared publications - Colin Cole
CQUniversity
6 shared publications Qing Wu
Cent Queensland Univ, Ctr Railway Engn CRE, Rockhampton, Qld 4702, Australia
5 shared publications
Latest Publications
- 16 November 2026
- Published by Springer Nature
- p. 32-42
Quantum Computing in Vehicle Dynamics and an Example of its Application to Locomotive Traction Control
- 16 November 2026
- Published by Springer Nature
- p. 32-42
Quantum Computing in Vehicle Dynamics and an Example of its Application to Locomotive Traction Control
- 7 November 2026
- Published by Springer Nature
- p. 87-97
Developing an AI-Infused Digital Twin Framework for the Automatic Generation of Vehicle System Dynamics Models
- 7 November 2026
- Published by Springer Nature
- p. 87-97
Developing an AI-Infused Digital Twin Framework for the Automatic Generation of Vehicle System Dynamics Models
- 7 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 240 (10) , 1254-1267
Understanding the impact of emulated initial rail roughness on traction performance under constant tribomachine testing conditions
This study used a twin-disc test under locomotive traction tribological conditions to investigate how initial surface roughness influences the traction coefficient at the wheel-rail interface. We propose functions to describe the evolution of disc surface roughness. The findings show that the initial roughness of the rail disc significantly impacted both traction coefficients and wear. Roughness values were selected based on measurements from a Western Australian freight line where tracks are subject to high tractive and dynamic braking efforts. Specifically, the wheel disc roughness was set at Ra = 1 μm for all samples, while the rail disc roughness values were set at Ra = 1 μm, 5 μm, and 10 μm. Experimental results revealed significantly different traction curves for each wheel-rail combination. Compared to the smoother 1 μm rail disc, the rougher discs (5 μm and 10 μm) exhibited a slower, linear increase in the traction coefficient before reaching a steady state. Notably, the 10 μm rail disc resulted in longer running-in periods, lower overall traction coefficients, and higher wear rates. This is attributed to the fact that contact asperities deformed plastically and were more easily removed during rolling/sliding. As a result, traction coefficients became similar for all tests following the running-in period.
- 7 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 240 (10) , 1254-1267
Understanding the impact of emulated initial rail roughness on traction performance under constant tribomachine testing conditions
This study used a twin-disc test under locomotive traction tribological conditions to investigate how initial surface roughness influences the traction coefficient at the wheel-rail interface. We propose functions to describe the evolution of disc surface roughness. The findings show that the initial roughness of the rail disc significantly impacted both traction coefficients and wear. Roughness values were selected based on measurements from a Western Australian freight line where tracks are subject to high tractive and dynamic braking efforts. Specifically, the wheel disc roughness was set at Ra = 1 μm for all samples, while the rail disc roughness values were set at Ra = 1 μm, 5 μm, and 10 μm. Experimental results revealed significantly different traction curves for each wheel-rail combination. Compared to the smoother 1 μm rail disc, the rougher discs (5 μm and 10 μm) exhibited a slower, linear increase in the traction coefficient before reaching a steady state. Notably, the 10 μm rail disc resulted in longer running-in periods, lower overall traction coefficients, and higher wear rates. This is attributed to the fact that contact asperities deformed plastically and were more easily removed during rolling/sliding. As a result, traction coefficients became similar for all tests following the running-in period.
- Open Access
- 26 February 2026
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 222
Monte Carlo modelling of frictional uncertainties in three-piece bogie hunting mechanisms
- 26 February 2026
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 222
Open AccessMonte Carlo modelling of frictional uncertainties in three-piece bogie hunting mechanisms
- Open Access
- 22 May 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 213
Multibody dynamic analysis of vibrational and frictional energy for railway freight wagons under different track irregularities and curve radii
- 22 May 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 213
Open AccessMultibody dynamic analysis of vibrational and frictional energy for railway freight wagons under different track irregularities and curve radii
- Open Access
- 22 May 2025
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 17 (5)
A review on frictional torque reduction approaches for energy efficient roller bearings
This review examines various strategies to enhance the energy efficiency of roller bearings by reducing frictional torques from multiple sources: roller rolling resistance, sliding friction at roller ends, lubricant agitation, interactions with bearing cages, and frictional losses in seals. The review shows that recent advancements emphasise the significance of design variables, lubrication strategies, and geometrical optimisations. Surface roughness, precision coatings, oil flow alternations, and bearing geometry also significantly influence frictional torque. This review highlights the potential for significant reduction of frictional torque through the implementation of energy-efficient seal designs as well as the importance of precise friction torque measurement methodologies. These insights underscore the need for ongoing research and development to further improve roller bearing efficiency and reliability across various applications.
- 22 May 2025
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 17 (5)
Open AccessA review on frictional torque reduction approaches for energy efficient roller bearings
This review examines various strategies to enhance the energy efficiency of roller bearings by reducing frictional torques from multiple sources: roller rolling resistance, sliding friction at roller ends, lubricant agitation, interactions with bearing cages, and frictional losses in seals. The review shows that recent advancements emphasise the significance of design variables, lubrication strategies, and geometrical optimisations. Surface roughness, precision coatings, oil flow alternations, and bearing geometry also significantly influence frictional torque. This review highlights the potential for significant reduction of frictional torque through the implementation of energy-efficient seal designs as well as the importance of precise friction torque measurement methodologies. These insights underscore the need for ongoing research and development to further improve roller bearing efficiency and reliability across various applications.
- 1 November 2024
- Published by Springer Nature
- p. 612-622
Implementation of the Rheological Dry Friction Model in Fastsim Algorithm for Locomotive Traction Studies
- 1 November 2024
- Published by Springer Nature
- p. 612-622
Implementation of the Rheological Dry Friction Model in Fastsim Algorithm for Locomotive Traction Studies