Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Federico Ravotti has a total of 1000 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Towards Qualification of Epoxy Resins for Superconducting Magnets Exposed to Radiation Doses Exceeding 100 MGy: Effect of the Radiation Source and Environment

    by Christian Scheuerlein, Federico Ravotti, Giuseppe Pezzulo, Torsten Koettig, Oliver Aberle, Ana-Paula Bernardes, Roland Piccin, Michael Eisterer

    To qualify epoxy resin systems for use in superconducting magnets of future particle accelerators up to peak doses beyond 100 MGy, the effects of the irradiation source, the irradiation environment and the irradiation temperature have been assessed. Identical epoxy resin samples have been irradiated with 60Co gamma rays, 24 GeV/c protons and by mixed neutron/gamma radiation in a reactor and at a spallation source up to a dose of 170 MGy. Irradiation-induced cross-linking and chain scission have been monitored by Dynamical Mechanical Analysis (DMA). When irradiations are performed with the same dose rate and in the same environment, the different radiation sources have a similar efficiency to produce radiation damage, and the total absorbed dose is a good scaling factor to compare irradiation effects in polymers. To distinguish between the influence of the irradiation temperature and of environmental oxygen, proton irradiations have been carried out in ambient air, inert gas at ambient temperature and in liquid helium. Compared to ambient air irradiation, in inert atmosphere more cross-linking is observed. Cross-linking rates are strongly reduced at 4.2 K. For some polymers the irradiation temperature has a strong influence on the chain scission rate. The most-radiation-hard epoxy resin systems maintain substantial mechanical strength up to doses beyond 100 MGy.


  • Open Access

    Facility intercomparison towards reliable very-high-energy heavy ion dosimetry for space electronics testing at CERN

    by Natalia Emriskova, Andreas Waets, Trevor Olsen, Rubén García Aliía, Daniel Söderström, Mario Sacristán Barbero, Matteo Cecchetto, Federico Ravotti, Giuseppe Pezzullo, Marc Delrieux, et al.

  • Open Access

    Processibility, Thermo-Mechanical Properties, and Radiation Hardness of Polyurethane and Silicone Resins

    by Christian Scheuerlein, Melanie Albeck, Roland Piccin, Federico Ravotti, Giuseppe Pezzullo

    Different polyurethanes (PURs) and silicone for potential use in particle accelerators and detectors have been characterized in the uncured state, after curing, and after exposure to ionizing irradiation in ambient air and in liquid helium. The viscosity evolution during processing was measured with a rheometer. Dynamic mechanical analysis (DMA) and Shore A hardness measurements were applied to detect irradiation-induced crosslinking and chain scission effects. Uniaxial tensile and flexural tests under ambient and cryogenic conditions have been performed to assess changes in mechanical strength, elongation at break, and elastic properties. The initial viscosity of 550 cP at 25 °C of the uncured PUR RE700-4 polyol and RE106 isocyanate system for protective encapsulation is sufficiently low for impregnation of small magnet coils, but the pot life of about 30 min is too short for impregnation of large magnet coils. The cured RE700-4 system has outstanding mechanical properties at 77 K (flexural strength, impact strength, and fracture toughness). When RE700-4 is exposed to ionizing radiation, chain scission and cross-linking occur at a similar rate. In the other casting systems, irradiation-induced changes are cross-linking dominated, as manifested by an increase of the rubbery shear modulus (G’rubbery), the ambient temperature Young’s modulus (ERT), and the Shore A hardness. Cross-linking rates are strongly reduced when irradiation occurs in liquid helium. The irradiation effect on mechanical properties can be strongly dependent on the testing temperature. The RT mechanical strength and strain at fracture of the cross-linking silicone is drastically decreased after 1.6 MGy, whereas its 77 K strain at fracture has almost doubled. In addition, 77 K elastic moduli are similar for all pure resins and only slightly affected by irradiation.


  • Open Access

    Proton reconstruction with the TOTEM Roman pot detectors for high-β* LHC data

    by A. Hayrapetyan, A. Tumasyan, W. Adam, J.W. Andrejkovic, L. Benato, T. Bergauer, S. Chatterjee, K. Damanakis, M. Dragicevic, P.S. Hussain, et al.

    The TOTEM Roman pot detectors are used to reconstruct the transverse momentum of scattered protons and to estimate the transverse location of the primary interaction. This paper presents new methods of track reconstruction, measurements of strip-level detection efficiencies, cross-checks of the LHC beam optics, and detector alignment techniques, along with their application in the selection of signal collision events. The track reconstruction is performed by exploiting hit cluster information through a novel method using a common polygonal area in the intercept-slope plane. The technique is applied in the relative alignment of detector layers with μm precision. A tag-and-probe method is used to extract strip-level detection efficiencies. The alignment of the Roman pot system is performed through time-dependent adjustments, resulting in a position accuracy of 3 μm in the horizontal and 60 μm in the vertical directions. The goal is to provide an optimal reconstruction tool for central exclusive physics analyses based on the high-β* data-taking period at √(s) = 13 TeV in 2018.

  • Open Access

    The HEARTS EU Project and Its Initial Results on Fragmented High-Energy Heavy-Ion Single-Event Effects Testing

    by Rubén García Alía, Andreas Waets, Andrea Coronetti, Kacper Bilko, Marc Delrieux, Natalia Emriskova, Luigi Esposito, Matthew Fraser, Eliott Johnson, Karolina Klimek, et al.

    We perform Single Event Effects (SEE) tests with well-characterized fully fragmented (i.e., beyond Bragg peak) high-energy heavy-ion beams and compare the results with those expected from conventional, mono-Linear Energy Transfer (LET) measurements, showing a satisfactory level of agreement between the two. This compliance paves the way to the exploitation of simulation tools for accurately quantifying the ion fragmentation impact on SEE rates for both ground-level testing conditions and space Galactic Cosmic Ray environments with electronics operating behind significant thicknesses of shielding. The satisfactory agreement level is also encouraging in view of the possible usage of fragmented heavy ion beams for ground-level SEE testing of electronics.


  • Open Access

    Search for high-mass exclusive diphoton production with tagged protons in proton-proton collisions at s=13  TeV

    by A. Tumasyan, W. Adam, J. W. Andrejkovic, T. Bergauer, S. Chatterjee, K. Damanakis, M. Dragicevic, A. Escalante Del Valle, P. S. Hussain, M. Jeitler, et al.

    A search is presented for high-mass exclusive diphoton production via photon-photon fusion in proton-proton collisions at s=13  TeV in events where both protons survive the interaction. The analysis utilizes data corresponding to an integrated luminosity of 103  fb−1 collected in 2016–2018 with the central CMS detector and the CMS and TOTEM precision proton spectrometer (PPS). Events that have two photons with high transverse momenta (pTγ>100  GeV), back-to-back in azimuth, and with a large diphoton invariant mass (mγγ>350  GeV) are selected. To remove the dominant inclusive diphoton backgrounds, the kinematic properties of the protons detected in PPS are required to match those of the central diphoton system. Only events having opposite-side forward protons detected with a fractional momentum loss between 0.035 and 0.15 (0.18) for the detectors on the negative (positive) side of CMS are considered. One exclusive diphoton candidate is observed for an expected background of 1.1 events. Limits at 95% confidence level are derived for the four-photon anomalous coupling parameters |ζ1|<0.073  TeV−4 and |ζ2|<0.15  TeV−4, using an effective field theory. Additionally, upper limits are placed on the production of axionlike particles with coupling strength to photons f−1 that varies from 0.03  TeV−1 to 1  TeV−1 over the mass range from 500 to 2000 GeV.


  • Open Access

    Nonresonant central exclusive production of charged-hadron pairs in proton-proton collisions at s=13  TeV

    by A. Hayrapetyan, A. Tumasyan, W. Adam, J. W. Andrejkovic, T. Bergauer, S. Chatterjee, K. Damanakis, M. Dragicevic, P. S. Hussain, M. Jeitler, et al.

    The central exclusive production of charged-hadron pairs in pp collisions at a center-of-mass energy of 13 TeV is examined, based on data collected in a special high-β* run of the LHC. The nonresonant continuum processes are studied with the invariant mass of the centrally produced two-pion system in the resonance-free region, mπ+π−<0.7 or mπ+π−>1.8  GeV. Differential cross sections as functions of the azimuthal angle between the surviving protons, squared exchanged four-momenta, and mπ+π− are measured in a wide region of scattered proton transverse momenta, between 0.2 and 0.8 GeV, and for pion rapidities |y|<2. A rich structure of interactions related to double-pomeron exchange is observed. A parabolic minimum in the distribution of the two-proton azimuthal angle is observed for the first time. It can be interpreted as an effect of additional pomeron exchanges between the protons from the interference between the bare and the rescattered amplitudes. After model tuning, various physical quantities are determined that are related to the pomeron cross section, proton-pomeron and meson-pomeron form factors, pomeron trajectory and intercept, and coefficients of diffractive eigenstates of the proton.


  • Open Access

    Fracture Toughness, Radiation Hardness, and Processibility of Polymers for Superconducting Magnets

    by Anders Gaarud, Christian Scheuerlein, David Mate Parragh, Sébastien Clement, Jacob Bertsch, Cedric Urscheler, Roland Piccin, Federico Ravotti, Giuseppe Pezzullo, Ralf Lach

    High fracture toughness at cryogenic temperature and radiation hardness can be conflicting requirements for the resins for the impregnation of superconducting magnet coils. The fracture toughness of different epoxy-resin systems at room temperature (RT) and at 77 K was measured, and their toughness was compared with that determined for a polyurethane, polycarbonate (PC) and poly(methyl methacrylate) (PMMA). Among the epoxy resins tested in this study, the MY750 system has the highest 77 K fracture toughness of KIC = 4.6 MPa√m, which is comparable to the KIC of PMMA, which also exhibits linear elastic behaviour and unstable crack propagation. The polyurethane system tested has a much higher 77 K toughness than the epoxy resins, approaching the toughness of PC, which is known as one of the toughest polymer materials. CTD101K is the least performing in terms of fracture toughness. Despite this, it is used for the impregnation of large Nb3Sn coils for its good processing capabilities and relatively high radiation resistance. In this study, the fracture toughness of CTD101K was improved by adding the polyglycol flexibiliser Araldite DY040 as a fourth component. The different epoxy-resin systems were exposed to proton and gamma doses up to 38 MGy, and it was found that adding the DY040 flexibiliser to the CTD101K system did not significantly change the irradiation-induced ageing behaviour. The viscosity evolution of the uncured resin mix is not significantly changed when adding the DY040 flexibiliser, and at the processing temperature of 60 °C, the viscosity remains below 200 cP for more than 24 h. Therefore, the new resin referred to as POLAB Mix is now used for the impregnation of superconducting magnet coils.


  • Open Access

    Effect of Irradiation Temperature and Atmosphere on Aging of Epoxy Resins for Superconducting Magnets

    by David Mate Parragh, Christian Scheuerlein, Noémie Martin, Roland Piccin, Federico Ravotti, Giuseppe Pezzullo, Torsten Koettig, Dirk Lellinger

    The superconducting magnets of future particle accelerators will be exposed to high irradiation doses at cryogenic temperatures. To investigate the effect of irradiation temperature and atmosphere on the aging behavior, we have characterized the changes in thermomechanical properties of six epoxy resins for potential use in superconducting magnets after irradiation up to 20 MGy in ambient air, inert gas, and liquid helium. Based on the results obtained by Dynamic Mechanical Analysis (DMA), we discuss the effect of irradiation temperature and the presence of oxygen. The irradiation temperature can have a strong influence on the rates at which cross-linking and chain scission occur.


  • Open Access

    CHARM High-Energy Ions for Microelectronics Reliability Assurance (CHIMERA)

    by Kacper Bilko, Rubén García Alía, Alessandra Constantino, Andrea Coronetti, Salvatore Danzeca, Marc Delrieux, Natalia Emriskova, Matthew Alexander Fraser, Sylvain Girard, Eliott Philippe Johnson, et al.

    We present the progress related to CERN’s capacity of delivering highly penetrating, high-LET heavy ions for radiation effect testing of electronic components within the CHIMERA (CHARM High-energy Ions for Micro Electronics Reliability Assurance) project. Profiting from the existing accelerator infrastructure, Monte Carlo simulations and a 300 μm-thick silicon diode, we highlight the beam characterization capabilities and a summary of the beam properties. Finally, we present the comparison of the SRAM SEE cross-section measurements with respect to other heavy ion facilities.