Dariusz Golański
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dariusz Golański has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Tomasz Chmielewski
Faculty of Mechanical and Industrial Engineering, Warsaw University of Technology, 00-661 Warszawa, Poland
15 shared publications - Paweł Kołodziejczak
Warsaw University of Technology
4 shared publications - Marcin Chmielewski
Łukasiewicz – Institute of Microelectronics and Photonics, Warsaw, Poland
3 shared publications - Piotr Siwek
Institute of Manufacturing Technologies, Warsaw University of Technology, 85 Narbutta str., 02-524 Warsaw, Poland
3 shared publications W. Włosiński
3 shared publications- Agnieszka Grabias
Łukasiewicz Research Network—Institute of Microelectronics and Photonics Warsaw Poland
2 shared publications
Latest Publications
- Open Access
RETRACTED: Chmielewski et al. Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases. Metals 2018, 8, 1059
The journal retracts the article “Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases”
Open AccessRETRACTED: Chmielewski et al. Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases. Metals 2018, 8, 1059
The journal retracts the article “Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases”
- Open Access
- 1 June 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (3) , 343-359
Effect of the Electrode Extension on the Geometry of Parts Made of 316LSi Steel by Wire Arc Additive Manufacturing Method (WAAM)
Intensive research is currently being conducted on WAAM (Wire Arc Additive Manufacturing) processes. Previous studies have demonstrated the impact of current parameters on altering the structure and properties of 316L stainless steel. However, there is a lack of comprehensive information in the...
- 1 June 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (3) , 343-359
Open AccessEffect of the Electrode Extension on the Geometry of Parts Made of 316LSi Steel by Wire Arc Additive Manufacturing Method (WAAM)
Intensive research is currently being conducted on WAAM (Wire Arc Additive Manufacturing) processes. Previous studies have demonstrated the impact of current parameters on altering the structure and properties of 316L stainless steel. However, there is a lack of comprehensive information in the...
- Open Access
- 1 January 2024
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 96, 107-116
Modeling and measurements of temperature field in the arc welding and hybrid plasma-MAG welding heat source models
The modelling of welding processes has recently become one of the most important tools to support the experimental research and the production implementation of welding processes. The literature is very rich in publications containing elements of single source modelling of welding processes, but the growing industrial interest in the use of hybrid welding sources creates a new field for the study of these processes using numerical simulations. In the present study, an attempt has been made to create a conventional and hybrid heat source in a software dedicated to performing numerical simulations using the FEA method - LUSAS FEA 14.7. As a result of the study, based on studies of the temperature field and thermal cycle of welding, it was possible to verify the classical Goldak model. Furthermore, the study showed that the proposed hybrid heat source model fairly well reflects the temperature distribution changes in hybrid welding.
- 1 January 2024
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 96, 107-116
Open AccessModeling and measurements of temperature field in the arc welding and hybrid plasma-MAG welding heat source models
The modelling of welding processes has recently become one of the most important tools to support the experimental research and the production implementation of welding processes. The literature is very rich in publications containing elements of single source modelling of welding processes, but the growing industrial interest in the use of hybrid welding sources creates a new field for the study of these processes using numerical simulations. In the present study, an attempt has been made to create a conventional and hybrid heat source in a software dedicated to performing numerical simulations using the FEA method - LUSAS FEA 14.7. As a result of the study, based on studies of the temperature field and thermal cycle of welding, it was possible to verify the classical Goldak model. Furthermore, the study showed that the proposed hybrid heat source model fairly well reflects the temperature distribution changes in hybrid welding.
- Open Access
- 7 August 2021
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 93 (3) , 11-29
Selected problems of design and pre-implementation studies of new types of manipulators
Conceptual development and testing of models and prototypes of manipulators, supporting the work of industrial robots, has become a specialty of the Department of Welding Engineering of the Warsaw University of Technology and ZAP Robotyka from Ostrow Wielkopolski. However, they are not typical devices, so their development requires a detailed analysis of many aspects, both functional and economic. Also the pre-implementation tests are not included in dedicated standards and must be based on previously developed experimental procedures. This article presents selected problems in the design and research of new types of manipulators, created as a result of joint research and development work.
- 7 August 2021
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 93 (3) , 11-29
Open AccessSelected problems of design and pre-implementation studies of new types of manipulators
Conceptual development and testing of models and prototypes of manipulators, supporting the work of industrial robots, has become a specialty of the Department of Welding Engineering of the Warsaw University of Technology and ZAP Robotyka from Ostrow Wielkopolski. However, they are not typical devices, so their development requires a detailed analysis of many aspects, both functional and economic. Also the pre-implementation tests are not included in dedicated standards and must be based on previously developed experimental procedures. This article presents selected problems in the design and research of new types of manipulators, created as a result of joint research and development work.
- Open Access
Microstructure of Rhenium Doped Ni-Cr Deposits Produced by Laser Cladding
The addition of Rhenium up to 6% to Ni-Cr alloys can dramatically improve the corrosion and oxide resistance of deposited coatings at high operating temperatures. Ni-Cr+Re layers can be successfully produced using conventional powder metallurgy, high rate solidification (HRS), or magnetron sputtering methods. However, in industrial applications, high-performance deposition methods are needed, e.g., laser cladding. Laser cladding has several advantages, e.g., metallurgical bonding, narrow heat-affected zone (HAZ), low dilution, and slight thermal damage to the substrate. In this paper, a powder Ni-Cr composite with 1% (wt.) of Rhenium was produced, then deposited onto a steel substrate (16Mo3) by laser cladding to assess the micro and macrostructural properties of the obtained layers. Besides the macro and microscopic observations, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) microanalysis of the deposit and HAZ as well as microhardness measurements have been conducted. The microstructure observations revealed four subareas of HAZ gradually changing from the fusion line towards the base material. Maximum hardness occurred in the HAZ, mainly in areas closer to the clad/substrate interface, reaching up to 350–400 HV. No sudden changes in the composition of the deposit and the area of fusion line were observed.
Open AccessMicrostructure of Rhenium Doped Ni-Cr Deposits Produced by Laser Cladding
The addition of Rhenium up to 6% to Ni-Cr alloys can dramatically improve the corrosion and oxide resistance of deposited coatings at high operating temperatures. Ni-Cr+Re layers can be successfully produced using conventional powder metallurgy, high rate solidification (HRS), or magnetron sputtering methods. However, in industrial applications, high-performance deposition methods are needed, e.g., laser cladding. Laser cladding has several advantages, e.g., metallurgical bonding, narrow heat-affected zone (HAZ), low dilution, and slight thermal damage to the substrate. In this paper, a powder Ni-Cr composite with 1% (wt.) of Rhenium was produced, then deposited onto a steel substrate (16Mo3) by laser cladding to assess the micro and macrostructural properties of the obtained layers. Besides the macro and microscopic observations, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) microanalysis of the deposit and HAZ as well as microhardness measurements have been conducted. The microstructure observations revealed four subareas of HAZ gradually changing from the fusion line towards the base material. Maximum hardness occurred in the HAZ, mainly in areas closer to the clad/substrate interface, reaching up to 350–400 HV. No sudden changes in the composition of the deposit and the area of fusion line were observed.
- Open Access
- 29 June 2020
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 92 (5) , 25-35
Verification of the welding heat source models in arc welding and hybrid plasma-MAG welding processes based on temperature field tests
Hybrid welding processes belong to a new group of welding varieties that most often combine two classic welding methods, such as laser welding with MIG/MAG welding or plasma welding with MAG welding. Modeling of welding stresses in this type of welding requires the definition of a new type of heat source model that combines a concentrated stream of energy with a classic heat source, which occurs in an electric arc. The paper presents the results of temperature field modeling in conventional MAG welding and hybrid plasma-MAG welding. In the first case, the heat source model described by Goldak was used, and in the second case, the Goldak model was combined with the developed rectangular heat source model with a homogeneous distribution. The temperature distributions obtained from the simulations were verified by spot temperature measurements during welding with thermocouples. A fairly good agreement of the numerical analysis results with the temperature measurements for MAG welding was obtained, while in the case of hybrid welding the discrepancies between the modeling and temperature measurements were greater. The results were discussed, indicating potential causes and factors influencing the obtained test results.
- 29 June 2020
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 92 (5) , 25-35
Open AccessVerification of the welding heat source models in arc welding and hybrid plasma-MAG welding processes based on temperature field tests
Hybrid welding processes belong to a new group of welding varieties that most often combine two classic welding methods, such as laser welding with MIG/MAG welding or plasma welding with MAG welding. Modeling of welding stresses in this type of welding requires the definition of a new type of heat source model that combines a concentrated stream of energy with a classic heat source, which occurs in an electric arc. The paper presents the results of temperature field modeling in conventional MAG welding and hybrid plasma-MAG welding. In the first case, the heat source model described by Goldak was used, and in the second case, the Goldak model was combined with the developed rectangular heat source model with a homogeneous distribution. The temperature distributions obtained from the simulations were verified by spot temperature measurements during welding with thermocouples. A fairly good agreement of the numerical analysis results with the temperature measurements for MAG welding was obtained, while in the case of hybrid welding the discrepancies between the modeling and temperature measurements were greater. The results were discussed, indicating potential causes and factors influencing the obtained test results.
- Open Access
- 27 January 2020
- Published by EDP Sciences in Manufacturing Review
- Vol. 7, 4
Weldability of S700MC steel welded with the hybrid plasma + MAG method
The paper describes the microstructure of welded joints produced by the plasma+MAG (Metal Active Gas) method of S700MC high yield strength steel (700 MPa). Welded joints of thermomechanical steel have been made with different values of heat input. The results of metallographic research of welded joints, microstructure of the weld and heat affected zone, hardness distribution and impact toughness are presented. The heat affected zone consists of two sub-zones with different grain size and lowered hardness. The tensile test show that strength of welded joints was slightly reduced and the bending test revealed no crack formation in the weld. The impact toughness of measured welded samples with V-notch in HAZ (heat affected zone) reached high values that are higher comparing to samples with notch placed in the weld area. The investigation results show that the use of plasma concentrated heat source together with MAG welding arc does not significantly change the structure and deteriorate properties of welded S700MC thermomechanically treated high strength steel. The hybrid plasma+MAG welding method has a potential to become a beneficial alternative to other welding processes due to its high efficiency, reduced amount of weld metal content or limited requirements for a preparation of edges of welded joints.
- 27 January 2020
- Published by EDP Sciences in Manufacturing Review
- Vol. 7, 4
Open AccessWeldability of S700MC steel welded with the hybrid plasma + MAG method
The paper describes the microstructure of welded joints produced by the plasma+MAG (Metal Active Gas) method of S700MC high yield strength steel (700 MPa). Welded joints of thermomechanical steel have been made with different values of heat input. The results of metallographic research of welded joints, microstructure of the weld and heat affected zone, hardness distribution and impact toughness are presented. The heat affected zone consists of two sub-zones with different grain size and lowered hardness. The tensile test show that strength of welded joints was slightly reduced and the bending test revealed no crack formation in the weld. The impact toughness of measured welded samples with V-notch in HAZ (heat affected zone) reached high values that are higher comparing to samples with notch placed in the weld area. The investigation results show that the use of plasma concentrated heat source together with MAG welding arc does not significantly change the structure and deteriorate properties of welded S700MC thermomechanically treated high strength steel. The hybrid plasma+MAG welding method has a potential to become a beneficial alternative to other welding processes due to its high efficiency, reduced amount of weld metal content or limited requirements for a preparation of edges of welded joints.
- Open Access
- 25 October 2019
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 91 (8) , 13-24
The effect of technological parameters of PMMA thermoplastic welding in the hot air stream on the quality of joints
The work covers the welding of thermoplastic polymethyl methacrylate (PMMA) and concerns the assessment of the impact of the main welding parameters on joint strength. The strength test of welded joints made of thermoplastic material was carried out. The aim of the study was to determine the influence of the main technological parameters of welding, such as: temperature and welding speed, gas stream output, filler rod pressure, diameter and type of hot air gun nozzle on the strength of the obtained joint. The method of sample preparation and testing was performed in accordance with the guidelines of PN-EN 12814-2: 2002 "Tests of welded joints in semi-finished products made of thermoplastics ‒ Part 2: Tensile test". Visual evaluation of welded samples and analysis of results obtained from the tensile test made it possible to draw conclusions about the influence of selected welding parameters on joint strength. The decisive influence on the strength of joints was caused by welding defects, in the form of lack of side wall fusion and porosity.
- 25 October 2019
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 91 (8) , 13-24
Open AccessThe effect of technological parameters of PMMA thermoplastic welding in the hot air stream on the quality of joints
The work covers the welding of thermoplastic polymethyl methacrylate (PMMA) and concerns the assessment of the impact of the main welding parameters on joint strength. The strength test of welded joints made of thermoplastic material was carried out. The aim of the study was to determine the influence of the main technological parameters of welding, such as: temperature and welding speed, gas stream output, filler rod pressure, diameter and type of hot air gun nozzle on the strength of the obtained joint. The method of sample preparation and testing was performed in accordance with the guidelines of PN-EN 12814-2: 2002 "Tests of welded joints in semi-finished products made of thermoplastics ‒ Part 2: Tensile test". Visual evaluation of welded samples and analysis of results obtained from the tensile test made it possible to draw conclusions about the influence of selected welding parameters on joint strength. The decisive influence on the strength of joints was caused by welding defects, in the form of lack of side wall fusion and porosity.
- Open Access
- 5 October 2019
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 91 (7) , 33-44
Study of design and research of new welding manipulators on the example of an L-type positioner
The development, testing and implementation of a new construction of a multi-axis L-type welding positioner designed to work with an industrial robot, distinguished by a wide range of movements, high load capacity and working space is a difficult task. Due to the special, unique nature of this type of devices, their research is not the subject of dedicated standards and detailed descriptions of literature and, are based primarily on their own manufacturers' procedures. The article traces the creative process in the development and implementation of the "L" positioner as part of the research and development of new types of machines at PPU "ZAP Robotics" in Ostrów Wielkopolski in cooperation with the Department of Welding Engineering at the Warsaw University of Technology.
- 5 October 2019
- Published by Agenda Wydawnicza SIMP Przeglad Spawalnictwa in Welding Technology Review
- Vol. 91 (7) , 33-44
Open AccessStudy of design and research of new welding manipulators on the example of an L-type positioner
The development, testing and implementation of a new construction of a multi-axis L-type welding positioner designed to work with an industrial robot, distinguished by a wide range of movements, high load capacity and working space is a difficult task. Due to the special, unique nature of this type of devices, their research is not the subject of dedicated standards and detailed descriptions of literature and, are based primarily on their own manufacturers' procedures. The article traces the creative process in the development and implementation of the "L" positioner as part of the research and development of new types of machines at PPU "ZAP Robotics" in Ostrów Wielkopolski in cooperation with the Department of Welding Engineering at the Warsaw University of Technology.
- Open Access
RETRACTED: Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases
The paper presents the results of research on the production by means of arc spraying of composite coatings from the Fe-Al system with participation of in-situ intermetallic phases. The arc spraying process was carried out by simultaneously melting two different electrode wires, aluminum and steel. The aim of the research is to create protective coatings with a composite structure with a significant participation of FexAly as an intermetallic phases reinforcement. The synthesis of intermetallic phases takes place during the (in-situ) spraying process. Currently most coatings involving intermetallic phases are manufactured by different thermal spraying methods using coating materials in the form of prefabricated powders containing intermetallic phases. The obtained results showed the local occurrence of intermetallic phases from the Fe-Al system, and the dominant components of the structure have two phases, aluminum solid solutions in iron and iron in aluminum. The participation of intermetallic phases in the coating is relatively low, but its effect on the properties of the coating material is significant.
Open AccessRETRACTED: Structure and Selected Properties of Arc Sprayed Coatings Containing In-Situ Fabricated Fe-Al Intermetallic Phases
The paper presents the results of research on the production by means of arc spraying of composite coatings from the Fe-Al system with participation of in-situ intermetallic phases. The arc spraying process was carried out by simultaneously melting two different electrode wires, aluminum and steel. The aim of the research is to create protective coatings with a composite structure with a significant participation of FexAly as an intermetallic phases reinforcement. The synthesis of intermetallic phases takes place during the (in-situ) spraying process. Currently most coatings involving intermetallic phases are manufactured by different thermal spraying methods using coating materials in the form of prefabricated powders containing intermetallic phases. The obtained results showed the local occurrence of intermetallic phases from the Fe-Al system, and the dominant components of the structure have two phases, aluminum solid solutions in iron and iron in aluminum. The participation of intermetallic phases in the coating is relatively low, but its effect on the properties of the coating material is significant.