Jarno Reuna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jarno Reuna has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Riku Isoaho
Tampere Univ, Fac Engn & Nat Sci, Optoelect Res Ctr, Phys Unit, POB 692, FIN-33014 Tampere, Finland
9 shared publications - Mircea Guina
Tampere University
7 shared publications - Arto Aho
Winse Power Oy 2 , Tekniikankatu 1, Tampere
6 shared publications Antti Tukiainen
5 shared publications- Antti Tukiainen
Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland
5 shared publications Arttu Hietalahti
Tampere Univ, Fac Engn & Nat Sci, Optoelect Res Ctr, Phys Unit, POB 692, FIN-33014 Tampere, Finland
5 shared publications
Latest Publications
- Open Access
- 7 November 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 16 (48) , 22383-22392
Production of mixed phase Ti3+-rich TiO2 thin films by oxide defect engineered crystallization
Oxygen vacancies and Ti3+ defects in the amorphous phase of TiO2 predetermine vacuum annealing induced crystallization. Anatase, nanocrystalline rutile or mixed phases can be created by defect engineering without affecting the O/Ti ratio.
- 7 November 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 16 (48) , 22383-22392
Open AccessProduction of mixed phase Ti3+-rich TiO2 thin films by oxide defect engineered crystallization
Oxygen vacancies and Ti3+ defects in the amorphous phase of TiO2 predetermine vacuum annealing induced crystallization. Anatase, nanocrystalline rutile or mixed phases can be created by defect engineering without affecting the O/Ti ratio.
- Open Access
- 1 December 2022
- Published by IOP Publishing in Nano Express
- Vol. 3 (4) , 044002
Ice resistance of hydrophobic fluoropolymerized nanostructured alumina films for antireflective coatings
The functionality and durability of nanostructured alumina coatings exposed to atmospheric icing has been assessed to probe their usability in practical applications and to estimate the need for further development of the coatings. In particular, the changes in surface microstructure and in optical performance as well as in the wetting characteristics of the surfaces are reported. Without a hydrophobicity treatment the alumina nanostructures are superhydrophilic and do not endure large environmental changes. Hydrophobicity treated fluoropolymerized nanostructured alumina provides characteristics with partial anti-icing capabilities, enhanced durability, and excellent transmission levels of >95%, but the performance degrades in cyclic icing/de-icing. However, the hydrophobic nanostructured alumina outperforms both the nanostructured and planar alumina coatings and possesses increased durability and stability even under harsh conditions, such as the atmospheric icing. This indicates a clear need to use a hydrophobicity treatment for the nanostructured alumina antireflection coatings to be used in any environments. Therefore, its utilization in applications where little or occasional exposure to icing or other humidity and temperature changes is favorable over standard planar coatings. Further process optimization of the hydrophobicity treatment is still needed for better durability for cyclical icing exposure.
- 1 December 2022
- Published by IOP Publishing in Nano Express
- Vol. 3 (4) , 044002
Open AccessIce resistance of hydrophobic fluoropolymerized nanostructured alumina films for antireflective coatings
The functionality and durability of nanostructured alumina coatings exposed to atmospheric icing has been assessed to probe their usability in practical applications and to estimate the need for further development of the coatings. In particular, the changes in surface microstructure and in optical performance as well as in the wetting characteristics of the surfaces are reported. Without a hydrophobicity treatment the alumina nanostructures are superhydrophilic and do not endure large environmental changes. Hydrophobicity treated fluoropolymerized nanostructured alumina provides characteristics with partial anti-icing capabilities, enhanced durability, and excellent transmission levels of >95%, but the performance degrades in cyclic icing/de-icing. However, the hydrophobic nanostructured alumina outperforms both the nanostructured and planar alumina coatings and possesses increased durability and stability even under harsh conditions, such as the atmospheric icing. This indicates a clear need to use a hydrophobicity treatment for the nanostructured alumina antireflection coatings to be used in any environments. Therefore, its utilization in applications where little or occasional exposure to icing or other humidity and temperature changes is favorable over standard planar coatings. Further process optimization of the hydrophobicity treatment is still needed for better durability for cyclical icing exposure.
- Open Access
- 19 November 2022
- Published by Elsevier in Thin Solid Films
- Vol. 763
Optimization of reactive ion beam sputtered Ta2O5 for III–V compounds
- 19 November 2022
- Published by Elsevier in Thin Solid Films
- Vol. 763
Open AccessOptimization of reactive ion beam sputtered Ta2O5 for III–V compounds
- Open Access
- 13 September 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 248
Optimized molecular beam epitaxy process for lattice-matched narrow-bandgap (0.8 eV) GaInNAsSb solar junctions
- 13 September 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 248
Open AccessOptimized molecular beam epitaxy process for lattice-matched narrow-bandgap (0.8 eV) GaInNAsSb solar junctions
- Open Access
- 8 September 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 248
Epitaxial lift-off process for GaAs solar cells controlled by InGaAs internal sacrificial stressor layers and a PMMA surface stressor
- 8 September 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 248
Open AccessEpitaxial lift-off process for GaAs solar cells controlled by InGaAs internal sacrificial stressor layers and a PMMA surface stressor
- Open Access
- 25 April 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5 (5) , 5804-5810
Optical Performance Assessment of Nanostructured Alumina Multilayer Antireflective Coatings Used in III–V Multijunction Solar Cells
The optical performance of a multilayer antireflective coating incorporating lithography-free nanostructured alumina is assessed. To this end, the performance of single-junction GaInP solar cells and four-junction GaInP/GaAs/GaInNAsSb/GaInNAsSb multijunction solar cells incorporating the nanostructured alumina is compared against the performance of similar solar cells using conventional double-layer antireflective coating. External quantum efficiency measurements for GaInP solar cells with the nanostructured coating demonstrate angle-independent operation, showing only a marginal difference at 60° incident angle. The average reflectance of the nanostructured antireflective coating is ∼3 percentage points smaller than the reflectance of the double-layer antireflective coating within the operation bandwidth of the GaInP solar cell (280-710 nm), which is equivalent of ∼0.2 mA/cm2 higher current density at AM1.5D (1000 W/m2). When used in conjunction with the four-junction solar cell, the nanostructured coating provides ∼0.8 percentage points lower average reflectance over the operation bandwidth from 280 to 1380 nm. However, it is noted that only the reflectance of the bottom GaInNAsSb junction is improved in comparison to the planar coating. In this respect, since in such solar cells the bottom junction typically is limiting the operation, the nanostructured coating would enable increasing the current density ∼0.6 mA/cm2 in comparison to the standard two-layer coating. The light-biased current-voltage measurements show that the fabrication process for the nanostructured coating does not induce notable recombination or loss mechanisms compared to the established deposition methods. Angle-dependent external quantum efficiency measurements incline that the nanostructured coating excels in oblique angles, and due to low reflectance at a 1000-1800 nm wavelength range, it is very promising for next-generation broadband multijunction solar cells with four or more junctions.
- 25 April 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5 (5) , 5804-5810
Open AccessOptical Performance Assessment of Nanostructured Alumina Multilayer Antireflective Coatings Used in III–V Multijunction Solar Cells
The optical performance of a multilayer antireflective coating incorporating lithography-free nanostructured alumina is assessed. To this end, the performance of single-junction GaInP solar cells and four-junction GaInP/GaAs/GaInNAsSb/GaInNAsSb multijunction solar cells incorporating the nanostructured alumina is compared against the performance of similar solar cells using conventional double-layer antireflective coating. External quantum efficiency measurements for GaInP solar cells with the nanostructured coating demonstrate angle-independent operation, showing only a marginal difference at 60° incident angle. The average reflectance of the nanostructured antireflective coating is ∼3 percentage points smaller than the reflectance of the double-layer antireflective coating within the operation bandwidth of the GaInP solar cell (280-710 nm), which is equivalent of ∼0.2 mA/cm2 higher current density at AM1.5D (1000 W/m2). When used in conjunction with the four-junction solar cell, the nanostructured coating provides ∼0.8 percentage points lower average reflectance over the operation bandwidth from 280 to 1380 nm. However, it is noted that only the reflectance of the bottom GaInNAsSb junction is improved in comparison to the planar coating. In this respect, since in such solar cells the bottom junction typically is limiting the operation, the nanostructured coating would enable increasing the current density ∼0.6 mA/cm2 in comparison to the standard two-layer coating. The light-biased current-voltage measurements show that the fabrication process for the nanostructured coating does not induce notable recombination or loss mechanisms compared to the established deposition methods. Angle-dependent external quantum efficiency measurements incline that the nanostructured coating excels in oblique angles, and due to low reflectance at a 1000-1800 nm wavelength range, it is very promising for next-generation broadband multijunction solar cells with four or more junctions.
- Open Access
- 1 January 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 234
High performance low-bandgap (0.8 eV) single junction GaInNAsSb solar cells incorporating Au-based back surface reflectors
- 1 January 2022
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 234
Open AccessHigh performance low-bandgap (0.8 eV) single junction GaInNAsSb solar cells incorporating Au-based back surface reflectors
- Open Access
- 1 October 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 142, 107278
Interference system for high pressure environment
- 1 October 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 142, 107278
Open AccessInterference system for high pressure environment
- Open Access
- 9 March 2021
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 29 (7) , 869-875
Wide spectral coverage (0.7–2.2 eV) lattice‐matched multijunction solar cells based on AlGaInP, AlGaAs and GaInNAsSb materials
We report on the progress in developing lattice‐matched GaAs‐based solar cells with focus on developing AlGaInP, AlGaAs, and GaInNAsSb materials, aiming at achieving a wide spectral coverage, that is, 0.7–2.2 eV. To this end, we first benchmark the performance of an upright four‐junction GaInP/GaAs/GaInNAsSb/GaInNAsSb solar cells grown by molecular beam epitaxy on p‐GaAs substrates with bandgaps of 1.88, 1.42, 1.17, and 0.93 eV, respectively. The four‐junction cell exhibited an efficiency of ~39% at 560‐sun illumination while showing good electrical performance even up to 1000 suns. As a first step to further improve the efficiency toward 50% level, we demonstrate AlGaInP (>2 eV) and GaInNAsSb (<0.8 eV) subcells. We prove that AlGaInP cells with 0.1 Al composition would exhibit current‐matching condition when being incorporated in a five‐junction architecture together with two GaInNAsSb bottom and AlGaAs top junctions. Furthermore, current matching required for a six‐junction tandem architecture is achieved for an Al composition of 0.26. Overall, the results open a practical path toward fabrication of lattice‐matched solar cells with more than four junctions.
- 9 March 2021
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 29 (7) , 869-875
Open AccessWide spectral coverage (0.7–2.2 eV) lattice‐matched multijunction solar cells based on AlGaInP, AlGaAs and GaInNAsSb materials
We report on the progress in developing lattice‐matched GaAs‐based solar cells with focus on developing AlGaInP, AlGaAs, and GaInNAsSb materials, aiming at achieving a wide spectral coverage, that is, 0.7–2.2 eV. To this end, we first benchmark the performance of an upright four‐junction GaInP/GaAs/GaInNAsSb/GaInNAsSb solar cells grown by molecular beam epitaxy on p‐GaAs substrates with bandgaps of 1.88, 1.42, 1.17, and 0.93 eV, respectively. The four‐junction cell exhibited an efficiency of ~39% at 560‐sun illumination while showing good electrical performance even up to 1000 suns. As a first step to further improve the efficiency toward 50% level, we demonstrate AlGaInP (>2 eV) and GaInNAsSb (<0.8 eV) subcells. We prove that AlGaInP cells with 0.1 Al composition would exhibit current‐matching condition when being incorporated in a five‐junction architecture together with two GaInNAsSb bottom and AlGaAs top junctions. Furthermore, current matching required for a six‐junction tandem architecture is achieved for an Al composition of 0.26. Overall, the results open a practical path toward fabrication of lattice‐matched solar cells with more than four junctions.
- 5 March 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (21) , 215602
Use of nanostructured alumina thin films in multilayer anti-reflective coatings
A new method for modification of planar multilayer structures to create nanostructured aluminum oxide anti-reflection coatings is reported. The method is non-toxic and low-cost, being based on treatment of the coating with heated de-ionized water after the deposition of aluminum oxide. The results show that the method provides a viable alternative for attaining a low reflectance ARC. In particular, a low average reflectivity of ∼3.3% is demonstrated in a broadband spectrum extending from 400 nm to 2000 nm for ARCs deposited on GaInP solar-cells, the typical material used as top-junction in solar cell tandem architectures. Moreover, the process is compatible with volume manufacturing technologies used in photovoltaics, such as ion beam sputtering and electron beam evaporation.
- 5 March 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (21) , 215602
Use of nanostructured alumina thin films in multilayer anti-reflective coatings
A new method for modification of planar multilayer structures to create nanostructured aluminum oxide anti-reflection coatings is reported. The method is non-toxic and low-cost, being based on treatment of the coating with heated de-ionized water after the deposition of aluminum oxide. The results show that the method provides a viable alternative for attaining a low reflectance ARC. In particular, a low average reflectivity of ∼3.3% is demonstrated in a broadband spectrum extending from 400 nm to 2000 nm for ARCs deposited on GaInP solar-cells, the typical material used as top-junction in solar cell tandem architectures. Moreover, the process is compatible with volume manufacturing technologies used in photovoltaics, such as ion beam sputtering and electron beam evaporation.