Seunghee Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Seunghee Han has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Sang Ho Lim
Korea University
4 shared publications Sang Ho Lim
3 shared publicationsMin Gyeong Cho
2 shared publicationsMin Seo
2 shared publicationsSang-Ho Lim
Department of Materials Science and Engineering, Korea University, Seoul 02841, Republic of Korea
2 shared publicationsSehoon Hwang
Center for Hydrogen·Fuel Cell Research Korea Institute of Science and Technology 14‐gil 5 Hwarang‐ro, Seongbuk‐gu Seoul 02792 Republic of Korea
2 shared publications
Latest Publications
- 1 March 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (3) , 033006
Low-Resistivity Cobalt and Ruthenium Ultra-Thin Film Deposition Using Bipolar HiPIMS Technique
Owing to the rapid growth of very large-scale integration technology at nanometer scales, cobalt and ruthenium interconnects are being used to solve the high-resistivity copper problem. However, with such interconnects, carbon contamination can occur during chemical vapor deposition and atomic layer deposition. Bipolar (BP) high-power impulse magnetron sputtering (HiPIMS) with a high ionization rate is an excellent vacuum process for depositing low-resistivity thin films. In this study, low-resistivity cobalt, ruthenium, and copper thin films were deposited using BP-HiPIMS, HiPIMS, and direct-current magnetron sputtering (DCMS). The resistivities of the cobalt, ruthenium, and copper thin films (<10 nm) deposited via BP-HiPIMS were 91.5, 75, and 35%, respectively, lower than the resistivities of the same film materials deposited using direct-current MS. To solve the low pass-through flux of cobalt, the target temperature was raised to the Curie temperature (approximately 1100 °C) using a thermal insulation backplate (Ti-6Al-4V), resulting in a resistivity reduction of about 73%. The study provides a novel method for the vacuum deposition of cobalt and ruthenium thin films.
- 1 March 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (3) , 033006
Low-Resistivity Cobalt and Ruthenium Ultra-Thin Film Deposition Using Bipolar HiPIMS Technique
Owing to the rapid growth of very large-scale integration technology at nanometer scales, cobalt and ruthenium interconnects are being used to solve the high-resistivity copper problem. However, with such interconnects, carbon contamination can occur during chemical vapor deposition and atomic layer deposition. Bipolar (BP) high-power impulse magnetron sputtering (HiPIMS) with a high ionization rate is an excellent vacuum process for depositing low-resistivity thin films. In this study, low-resistivity cobalt, ruthenium, and copper thin films were deposited using BP-HiPIMS, HiPIMS, and direct-current magnetron sputtering (DCMS). The resistivities of the cobalt, ruthenium, and copper thin films (<10 nm) deposited via BP-HiPIMS were 91.5, 75, and 35%, respectively, lower than the resistivities of the same film materials deposited using direct-current MS. To solve the low pass-through flux of cobalt, the target temperature was raised to the Curie temperature (approximately 1100 °C) using a thermal insulation backplate (Ti-6Al-4V), resulting in a resistivity reduction of about 73%. The study provides a novel method for the vacuum deposition of cobalt and ruthenium thin films.
- 28 July 2021
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 4 (8) , 8641-8643
Correction to “Sub-5 nm Nanodiamonds Fabricated by Plasma Immersion Ion Implantation as Fluorescent Probes”
- 28 July 2021
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 4 (8) , 8641-8643
Correction to “Sub-5 nm Nanodiamonds Fabricated by Plasma Immersion Ion Implantation as Fluorescent Probes”
- 26 January 2021
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 4 (2) , 2238-2246
Sub-5 nm Nanodiamonds Fabricated by Plasma Immersion Ion Implantation as Fluorescent Probes
- 26 January 2021
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 4 (2) , 2238-2246
Sub-5 nm Nanodiamonds Fabricated by Plasma Immersion Ion Implantation as Fluorescent Probes
- 9 December 2019
- Published by Wiley in Advanced Materials Interfaces
- Vol. 7 (2) , 1901326
Porous Strained Pt Nanostructured Thin‐Film Electrocatalysts via Dealloying for PEM Fuel Cells
The exploitation of state‐of‐the‐art Pt/C electrocatalysts for polymer electrolyte membrane fuel cells (PEMFCs) is mostly limited, due to high Pt loading and durability issues caused by electrochemical instability of the carbon support in high potential regimes. In this study, the authors report that high‐compressive 3D Pt nanostructured thin films can considerably increase the catalytic activity and electrochemical durability of electrocatalysts under PEMFC device operating conditions. The nanostructure fabrication relies on the dealloying or selective leaching of solid alloys of Pt–C binary film to produce a residual 3D nanoporous thin‐film structure. A very rich structural behavior from the dealloying is shown, in which stress relief plays a governing role; the films possess a 3D structure of randomly interpenetrating ligaments and hierarchical pores with sizes between less than 50 nm and several tens of micrometers. In addition, a significant change is observed in the average lattice constant (1.55% compressive strain), which can tune the structural and electronic states of catalytic sites for enhancing the activity of the Pt electrocatalysts. Electrochemical performance of the fabricated porous strained Pt thin‐film electrocatalysts in both half‐cell and single‐cell analyses has demonstrated activity and durability superior to benchmark carbon support Pt catalysts.
- 9 December 2019
- Published by Wiley in Advanced Materials Interfaces
- Vol. 7 (2) , 1901326
Porous Strained Pt Nanostructured Thin‐Film Electrocatalysts via Dealloying for PEM Fuel Cells
The exploitation of state‐of‐the‐art Pt/C electrocatalysts for polymer electrolyte membrane fuel cells (PEMFCs) is mostly limited, due to high Pt loading and durability issues caused by electrochemical instability of the carbon support in high potential regimes. In this study, the authors report that high‐compressive 3D Pt nanostructured thin films can considerably increase the catalytic activity and electrochemical durability of electrocatalysts under PEMFC device operating conditions. The nanostructure fabrication relies on the dealloying or selective leaching of solid alloys of Pt–C binary film to produce a residual 3D nanoporous thin‐film structure. A very rich structural behavior from the dealloying is shown, in which stress relief plays a governing role; the films possess a 3D structure of randomly interpenetrating ligaments and hierarchical pores with sizes between less than 50 nm and several tens of micrometers. In addition, a significant change is observed in the average lattice constant (1.55% compressive strain), which can tune the structural and electronic states of catalytic sites for enhancing the activity of the Pt electrocatalysts. Electrochemical performance of the fabricated porous strained Pt thin‐film electrocatalysts in both half‐cell and single‐cell analyses has demonstrated activity and durability superior to benchmark carbon support Pt catalysts.
- 1 March 2019
- Published by Elsevier in Applied Surface Science
- Vol. 471, 878-886
Highly adhesive and bioactive Ti–Mg alloy thin film on polyether ether ketone formed by PIII&D technique
- 1 March 2019
- Published by Elsevier in Applied Surface Science
- Vol. 471, 878-886
Highly adhesive and bioactive Ti–Mg alloy thin film on polyether ether ketone formed by PIII&D technique
- 9 April 2016
- Published by Springer Nature in Metals and Materials International
- Vol. 22 (3) , 535-543
Al-Si-N/a-SiN:H thin-film coating for polycarbonate glazing applications
- 9 April 2016
- Published by Springer Nature in Metals and Materials International
- Vol. 22 (3) , 535-543
Al-Si-N/a-SiN:H thin-film coating for polycarbonate glazing applications
- Open Access
- 21 November 2014
- Published by Springer Nature in Scientific Reports
- Vol. 4 (1) , 7154
Triple-Junction Hybrid Tandem Solar Cells with Amorphous Silicon and Polymer-Fullerene Blends
Organic-inorganic hybrid tandem solar cells attract a considerable amount of attention due to their potential for realizing high efficiency photovoltaic devices at a low cost. Here, highly efficient triple-junction (TJ) hybrid tandem solar cells consisting of a double-junction (DJ) amorphous silicon (a-Si) cell and an organic photovoltaic (OPV) rear cell were developed. In order to design the TJ device in a logical manner, a simulation was carried out based on optical absorption and internal quantum efficiency. In the TJ architecture, the high-energy photons were utilized in a more efficient way than in the previously reported a-Si/OPV DJ devices, leading to a significant improvement in the overall efficiency by means of a voltage gain. The interface engineering such as tin-doped In2O3 deposition as an interlayer and its UV-ozone treatment resulted in the further improvement in the performance of the TJ solar cells. As a result, a power conversion efficiency of 7.81% was achieved with an open-circuit voltage of 2.35[emsp14]V. The wavelength-resolved absorption profile provides deeper insight into the detailed optical response of the TJ hybrid solar cells.
- 21 November 2014
- Published by Springer Nature in Scientific Reports
- Vol. 4 (1) , 7154
Open AccessTriple-Junction Hybrid Tandem Solar Cells with Amorphous Silicon and Polymer-Fullerene Blends
Organic-inorganic hybrid tandem solar cells attract a considerable amount of attention due to their potential for realizing high efficiency photovoltaic devices at a low cost. Here, highly efficient triple-junction (TJ) hybrid tandem solar cells consisting of a double-junction (DJ) amorphous silicon (a-Si) cell and an organic photovoltaic (OPV) rear cell were developed. In order to design the TJ device in a logical manner, a simulation was carried out based on optical absorption and internal quantum efficiency. In the TJ architecture, the high-energy photons were utilized in a more efficient way than in the previously reported a-Si/OPV DJ devices, leading to a significant improvement in the overall efficiency by means of a voltage gain. The interface engineering such as tin-doped In2O3 deposition as an interlayer and its UV-ozone treatment resulted in the further improvement in the performance of the TJ solar cells. As a result, a power conversion efficiency of 7.81% was achieved with an open-circuit voltage of 2.35[emsp14]V. The wavelength-resolved absorption profile provides deeper insight into the detailed optical response of the TJ hybrid solar cells.
- 1 August 2014
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 14 (8) , 6309-6313
Electroless Chemical Grafting of Nitrophenyl Groups on n-Doped Hydrogenated Amorphous Silicon Surfaces
The direct spontaneous grafting of 4-nitrophenyl molecules onto n-doped hydrogenated amorphous silicon (a-Si:H) surfaces without external ultraviolet, thermal, or electrochemical energy was investigated. Clean n-doped a-Si:H thin films were dipped in a solution of 4-nitrobenzenediazonium salts (PNBD) in acetonitrile. After the modified surfaces were rinsed, they were analyzed qualitatively and quantitatively by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). XPS and AFM results show that the reaction of an n-doped a-Si:H thin film with PNBD self-terminates without polymerization after 5 h, and the surface number density of 4-nitrophenyl molecules is 4.2×1015/cm2. These results demonstrate that the spontaneous grafting of nitrophenyl layers onto n-doped a-Si:H thin films is an attractive pathway toward forming interfaces between a-Si:H and organic layers under ambient conditions.
- 1 August 2014
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 14 (8) , 6309-6313
Electroless Chemical Grafting of Nitrophenyl Groups on n-Doped Hydrogenated Amorphous Silicon Surfaces
The direct spontaneous grafting of 4-nitrophenyl molecules onto n-doped hydrogenated amorphous silicon (a-Si:H) surfaces without external ultraviolet, thermal, or electrochemical energy was investigated. Clean n-doped a-Si:H thin films were dipped in a solution of 4-nitrobenzenediazonium salts (PNBD) in acetonitrile. After the modified surfaces were rinsed, they were analyzed qualitatively and quantitatively by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). XPS and AFM results show that the reaction of an n-doped a-Si:H thin film with PNBD self-terminates without polymerization after 5 h, and the surface number density of 4-nitrophenyl molecules is 4.2×1015/cm2. These results demonstrate that the spontaneous grafting of nitrophenyl layers onto n-doped a-Si:H thin films is an attractive pathway toward forming interfaces between a-Si:H and organic layers under ambient conditions.