Bo Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bo Jiang has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
Maoliang Hu
School of Materials Science and Chemical Engineering, Harbin University of Science and Technology, China
7 shared publicationsYe Wang
7 shared publicationsHongyu Xu
School of Materials Science and Chemical Engineering, Harbin University of Science and Technology, China
6 shared publicationsYu Guo
School of Intelligent Manufacturing, Huzhou College, Zhejiang, China
6 shared publications- Hongyu Xu
School of materials science and chemical engineering, Harbin University of Science and Technology, Harbin, China
5 shared publications - Ye Wang
Harbin University of Science and Technology
5 shared publications
Latest Publications
- 8 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Simultaneously improving thermal conductivity and mechanical properties of Al-Si alloys: Based on the influence of microscopic defects and second phase
To reveal the combined effect of defects and second phases on the thermal conductivity of Al-Si alloys, the defects and second phase of materials heat treatment was controlled by cryorolling and heat treatment. The correlation between thermal conductivity, grain boundaries, the morphology of the second phase, and dislocations was studied in this work. The results indicate that the Al-Si alloy possesses the highest thermal conductivity after heat treatment following 15% deformation, with an 11.8% increase compared to the as-cast alloy and a 59.44% increase in tensile strength. At 15% deformation, increased grain boundary density and dislocations due to grain fragmentation increased the probability of scattering of electrons and phonons, thereby limiting electron and phonon conduction. Nevertheless, electrons demonstrate a proclivity for traversing pathways with low resistivity to avoid passing through more grain boundaries, this reduces the effect of grain boundaries on electron conduction. The enhancement in thermal conductivity resulting from the decreases of second phase size has not been completely negated by the effectiveness of grain refinement. After the heat treatment, a large number of dislocations disappeared, and the second phase was broken into smaller segments and gradually spheroidized, which improved the electron and phonon conduction. Furthermore, the mechanical properties were also improved by dispersion strengthening and grain refinement strengthening. This work delved into the mechanism by which second phases and defects affect the thermal conductivity and mechanical properties of the alloys and provided an important theoretical basis for further research.
- 8 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Simultaneously improving thermal conductivity and mechanical properties of Al-Si alloys: Based on the influence of microscopic defects and second phase
To reveal the combined effect of defects and second phases on the thermal conductivity of Al-Si alloys, the defects and second phase of materials heat treatment was controlled by cryorolling and heat treatment. The correlation between thermal conductivity, grain boundaries, the morphology of the second phase, and dislocations was studied in this work. The results indicate that the Al-Si alloy possesses the highest thermal conductivity after heat treatment following 15% deformation, with an 11.8% increase compared to the as-cast alloy and a 59.44% increase in tensile strength. At 15% deformation, increased grain boundary density and dislocations due to grain fragmentation increased the probability of scattering of electrons and phonons, thereby limiting electron and phonon conduction. Nevertheless, electrons demonstrate a proclivity for traversing pathways with low resistivity to avoid passing through more grain boundaries, this reduces the effect of grain boundaries on electron conduction. The enhancement in thermal conductivity resulting from the decreases of second phase size has not been completely negated by the effectiveness of grain refinement. After the heat treatment, a large number of dislocations disappeared, and the second phase was broken into smaller segments and gradually spheroidized, which improved the electron and phonon conduction. Furthermore, the mechanical properties were also improved by dispersion strengthening and grain refinement strengthening. This work delved into the mechanism by which second phases and defects affect the thermal conductivity and mechanical properties of the alloys and provided an important theoretical basis for further research.
- 7 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 100
Enhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
- 7 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 100
Enhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
- Open Access
- 25 August 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
Shot peening (SP) was applied to A356 aluminum alloy for 30, 180, and 300 s to clarify the influence of the modified surface layer on corrosion behavior in 3.5 wt.% NaCl solution. SP roughened the surface and produced a plastically deformed layer. Its thickness increased from 17.97 μm after 30 s to 42.54 μm after 180 s and 69.28 μm after 300 s. Longer treatment promoted grain refinement, compressive residual stress, and a high density of dislocations in the near surface region. Electrochemical measurements showed that the corrosion current density decreased from 37.949 μA/cm2 for the untreated alloy to 11.354 μA/cm2 after 300 s SP. The 300 s sample also exhibited the largest capacitive loop and the highest film resistance and charge transfer resistance. Immersion tests revealed a clear dependence on exposure time. Surface roughening promoted chloride retention and local attack during the early stage. After 20 days, the untreated alloy suffered severe localized corrosion with deep pits, whereas the 300 s sample retained more intact substrate and showed shallower damage. XPS identified Al2O3, AlOOH, and Al(OH)3 as the main corrosion products. Grain refinement promoted compact oxide/hydroxide layer formation, compressive residual stress restrained corrosion propagation, and dislocations provided nucleation sites for protective species. Their combined effects stabilized the protective layer and improved long term corrosion resistance.
- 25 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
Shot peening (SP) was applied to A356 aluminum alloy for 30, 180, and 300 s to clarify the influence of the modified surface layer on corrosion behavior in 3.5 wt.% NaCl solution. SP roughened the surface and produced a plastically deformed layer. Its thickness increased from 17.97 μm after 30 s to 42.54 μm after 180 s and 69.28 μm after 300 s. Longer treatment promoted grain refinement, compressive residual stress, and a high density of dislocations in the near surface region. Electrochemical measurements showed that the corrosion current density decreased from 37.949 μA/cm2 for the untreated alloy to 11.354 μA/cm2 after 300 s SP. The 300 s sample also exhibited the largest capacitive loop and the highest film resistance and charge transfer resistance. Immersion tests revealed a clear dependence on exposure time. Surface roughening promoted chloride retention and local attack during the early stage. After 20 days, the untreated alloy suffered severe localized corrosion with deep pits, whereas the 300 s sample retained more intact substrate and showed shallower damage. XPS identified Al2O3, AlOOH, and Al(OH)3 as the main corrosion products. Grain refinement promoted compact oxide/hydroxide layer formation, compressive residual stress restrained corrosion propagation, and dislocations provided nucleation sites for protective species. Their combined effects stabilized the protective layer and improved long term corrosion resistance.
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
Shot peening (SP) was applied to A356 aluminum alloy for 30, 180, and 300 s to clarify the influence of the modified surface layer on corrosion behavior in 3.5 wt.% NaCl solution. SP roughened the surface and produced a plastically deformed layer. Its thickness increased from 17.97 μm after 30 s to 42.54 μm after 180 s and 69.28 μm after 300 s. Longer treatment promoted grain refinement, compressive residual stress, and a high density of dislocations in the near surface region. Electrochemical measurements showed that the corrosion current density decreased from 37.949 μA/cm2 for the untreated alloy to 11.354 μA/cm2 after 300 s SP. The 300 s sample also exhibited the largest capacitive loop and the highest film resistance and charge transfer resistance. Immersion tests revealed a clear dependence on exposure time. Surface roughening promoted chloride retention and local attack during the early stage. After 20 days, the untreated alloy suffered severe localized corrosion with deep pits, whereas the 300 s sample retained more intact substrate and showed shallower damage. XPS identified Al2O3, AlOOH, and Al(OH)3 as the main corrosion products. Grain refinement promoted compact oxide/hydroxide layer formation, compressive residual stress restrained corrosion propagation, and dislocations provided nucleation sites for protective species. Their combined effects stabilized the protective layer and improved long term corrosion resistance.
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced corrosion resistance of A356 aluminum alloy via shot peening surface modification
Shot peening (SP) was applied to A356 aluminum alloy for 30, 180, and 300 s to clarify the influence of the modified surface layer on corrosion behavior in 3.5 wt.% NaCl solution. SP roughened the surface and produced a plastically deformed layer. Its thickness increased from 17.97 μm after 30 s to 42.54 μm after 180 s and 69.28 μm after 300 s. Longer treatment promoted grain refinement, compressive residual stress, and a high density of dislocations in the near surface region. Electrochemical measurements showed that the corrosion current density decreased from 37.949 μA/cm2 for the untreated alloy to 11.354 μA/cm2 after 300 s SP. The 300 s sample also exhibited the largest capacitive loop and the highest film resistance and charge transfer resistance. Immersion tests revealed a clear dependence on exposure time. Surface roughening promoted chloride retention and local attack during the early stage. After 20 days, the untreated alloy suffered severe localized corrosion with deep pits, whereas the 300 s sample retained more intact substrate and showed shallower damage. XPS identified Al2O3, AlOOH, and Al(OH)3 as the main corrosion products. Grain refinement promoted compact oxide/hydroxide layer formation, compressive residual stress restrained corrosion propagation, and dislocations provided nucleation sites for protective species. Their combined effects stabilized the protective layer and improved long term corrosion resistance.
- 8 February 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (22) , 22276-22286
Effects of Different Heat Treatment Processes on Microstructure and Corrosion Resistance of PAAM-Inconel 718 Alloy
- 8 February 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (22) , 22276-22286
Effects of Different Heat Treatment Processes on Microstructure and Corrosion Resistance of PAAM-Inconel 718 Alloy
- 12 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (15) , 14916-14926
Effects of Semi-Solid Isothermal Heat Treatment on the Tribological Behavior of Al-15%Mg2Si-5%TiB2 Composites
- 12 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (15) , 14916-14926
Effects of Semi-Solid Isothermal Heat Treatment on the Tribological Behavior of Al-15%Mg2Si-5%TiB2 Composites
- 12 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (21) , 24845-24855
Interface Structure and Strengthening Mechanism of AZ91 Alloy Reinforced by MgO-Coated Graphene Nanoplatelets
- 12 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (21) , 24845-24855
Interface Structure and Strengthening Mechanism of AZ91 Alloy Reinforced by MgO-Coated Graphene Nanoplatelets
- Open Access
- 28 March 2025
- Published by Springer Nature in China Foundry
- Vol. 22 (4) , 385-394
Effect of La content on microstructure, tensile properties, and electrical conductivity of cast Al-Mg-Si-xLa alloys
- 28 March 2025
- Published by Springer Nature in China Foundry
- Vol. 22 (4) , 385-394
Open AccessEffect of La content on microstructure, tensile properties, and electrical conductivity of cast Al-Mg-Si-xLa alloys
- 26 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Refining mechanism of primary Mg2Si and wear resistance in Al-15 %Mg2Si composites by TiB2 particles addition
- 26 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Refining mechanism of primary Mg2Si and wear resistance in Al-15 %Mg2Si composites by TiB2 particles addition