JTJames Thomas

James Thomas

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


James Thomas has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Powder adhesion on tools during pharmaceutical tablet manufacturing

    by James V. Thomas, Antonios Zavaliangos

    The occurrence of defects in pharmaceutical tablets during manufacture can have disastrous consequences that impact quality, time, cost, and patients. 'Sticking', is a prominent tablet defect that results in the removal of material from the tablet surface after each compaction and its accumulation on the punch faces during tablet production. Currently, the understanding on the various mechanisms of sticking and methods of its assessment are inadequate. In this work, a novel laser reflection sensor was developed to quantify sticking with high sensitivity, live measurements, contact-free and simple to operate. The laser sensor compensates for the drawbacks of currently available techniques. Current techniques are largely unreliable or require large quantities of active drug or require stopping the press for assessment or not accessible as they require the use of specialized and complex instruments. Moreover, a novel material-sparing methodology (Single Tablet Multi-Compaction, STMC) for the assessment of sticking was introduced here. The results presented in this work demonstrate that STMC is a viable method which requires only a few tablets to assess sticking. Together, the STMC methodology and the laser sensor aim to address a pressing need in the pharmaceutical industry; that is to enable the early warning and mitigation of sticking to avoid its disastrous occurrence during production. In this work, the laser sensor enabled the discovery of a set of conditions that affect sticking that has not been reported before in literature. The effect of pre-compression pressure, punch temperature, and punch surface contamination were studied, and all found to strongly affect sticking. The results provide new insights into the complex mechanisms by which sticking occurs.


  • Sticking Detection by Repeated Compactions on a Single Tablet

    by James Thomas, Phuong Bui, Antonios Zavaliangos

    “Sticking” during tablet manufacture is the term used to describe the accumulation of adhered tablet material on the punch over the course of s


  • Evaluation and study on the adhesion of powder onto punch faces during tablet compaction

    by James V. Thomas, Antonios Zavaliangos

    Sticking during tablet compaction is an issue that is commonly experienced during tablet manufacturing operations. The term 'Sticking' refers to a phenomenon that results in the adherence of materials onto the punch faces and die wall even after the tooling has left contact with the tablet. The occurrence of sticking during large scale tablet manufacture can produce defective tablets, halt manufacturing operations, and can be very costly. Currently, the mechanisms by which this phenomenon occurs is not clearly understood. However, numerous factors dealing with powder characteristics and instrumentation parameters are reported in literature to affect sticking. Therefore, sticking is a complex multifaceted phenomenon in which multiple factors can simultaneously contribute to the issue. The aim of the work conducted in this thesis is to study the process of sticking. Ibuprofen was chosen as a model compound in this work as it is widely known to cause this issue. In addition, evaluation of the sticking propensity of Acetylsalicylic Acid (ASA) and of a confidential compound is also presented. A customized punch with a removable punch tip was used to quantify the mass of adhered material on the punch tip during tablet compaction. The effect of particle size on sticking with ibuprofen was evaluated. Formulations containing 30% ibuprofen (AS-IS) and 30% micronized ibuprofen with 0.5% magnesium stearate and 69.5% microcrystalline cellulose were tested. Results with micronized ibuprofen showed a marked increase in sticking compared to non-micronized ibuprofen. Significant triboelectric charging was observed with micronized ibuprofen. Analysis of the adhered material on the punch tip by SEM reveals the presence of both heavily deformed particles and minimally deformed fragments that are on the size order of well below 50[mu]m. Triboelectric charging was also demonstrated to occur upon compaction with ASA. Results suggest that that particle size, static charging and fragmentation may play important roles in the mechanism of sticking in ibuprofen formulations. Furthermore, it is observed that sticking in ibuprofen can be influenced by cleaning of punch faces by solvents and by capping defects in tablets.

  • Open Access

    Permutations with equal orders

    by Huseyin Acan, Charles Burnette, Sean Eberhard, Eric Schmutz, James Thomas

    Let ${\mathbb{P}}(ord\pi = ord\pi ')$ be the probability that two independent, uniformly random permutations of [n] have the same order. Answering a question of Thibault Godin, we prove that ${\mathbb{P}}(ord\pi = ord\pi ') = {n^{ - 2 + o(1)}}$ and that ${\mathbb{P}}(ord\pi = ord\pi ') \ge {1 \over 2}{n^{ - 2}}lg*n$ for infinitely manyn. (Herelg*nis the height of the tallest tower of twos that is less than or equal ton.)


  • Scanning Electron Microscope Observations of Powder Sticking on Punches during a Limited Number (N < 5) of Compactions of Acetylsalicylic Acid

    by Henrietta Tsosie, James Thomas, John Strong, Antonios Zavaliangos

    To obtain quantitative information and mechanistic insight into the problem of sticking of acetylsalicylic acid tablets on a metallic punch.