JLJames H. Lever

James H. Lever

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


James H. Lever has a total of 42 co-authors. Here are the top co-authors by number of shared publications:

  • Susan Taylor

    Cold Regions Research and Engineering Laboratory, US Army Engineer Research and Development Center, Hanover, New Hampshire03755, USA

    5 shared publications
  • Emily Asenath-Smith

    Cold Regions Research and Engineering Laboratory, US Army Engineer Research and Development Center, Hanover, New Hampshire03755, USA

    3 shared publications
  • Garrett R. Hoch

    Cold Regions Research and Engineering Laboratory, US Army Engineer Research and Development Center, Hanover, New Hampshire03755, USA

    2 shared publications
  • Alessandra Rotundi

    Department of Science and Technology, Parthenope University of Naples, 80143 Naples, Italy

    1 shared publication
  • Arnold J. Song

    Cold Regions Research and Engineering Laboratory, US Army Engineer Research and Development Center

    1 shared publication
  • Austin P. Lines

    Cold Regions Research and Engineering Laboratory, US Army Engineer Research and Development Center, Hanover, NH, United States

    1 shared publication

Latest Publications

  • Open Access

    Micrometeorite collections: a review and their current status

    by Matthias van Ginneken, Penelope J. Wozniakiewicz, Donald E. Brownlee, Vinciane Debaille, Vincenzo Della Corte, Lucie Delauche, Jean Duprat, Cecile Engrand, Luigi Folco, Marc Fries, et al.

    Micrometeorites are estimated to represent the main part of the present flux of extraterrestrial matter found on the Earth’s surface and provide valuable samples to probe the interplanetary medium. Here, we describe large and representative collections of micrometeorites currently available to the scientific community. These include Antarctic collections from surface ice and snow, as well as glacial sediments from the eroded top of nunataks—summits outcropping from the icesheet—and moraines. Collections extracted from deep-sea sediments (DSS) produced a large number of micrometeorites, in particular, iron-rich cosmic spherules that are rarer in other collections. Collections from the old and stable surface of the Atacama Desert show that finding large numbers of micrometeorites is not restricted to polar regions or DSS. The advent of rooftop collections marks an important step into involving citizen science in the study of micrometeorites, as well as providing potential sampling locations over all latitudes to explore the modern flux. We explore their strengths of the collections to address specific scientific questions and their potential weaknesses. The future of micrometeorite research will involve the finding of large fossil micrometeorite collections and benefit from recent advances in sampling cosmic dust directly from the air. This article is part of the theme issue ‘Dust in the Solar System and beyond’.


  • Open Access

    Revisiting mechanics of ice–skate friction: from experiments at a skating rink to a unified hypothesis

    by James H. Lever, Austin P. Lines, Susan Taylor, Garrett R. Hoch, Emily Asenath-Smith, Devinder S. Sodhi

    The mechanics underlying ice–skate friction remain uncertain despite over a century of study. In the 1930s, the theory of self-lubrication from frictional heat supplanted an earlier hypothesis that pressure melting governed skate friction. More recently, researchers have suggested that a layer of abraded wear particles or the presence of quasi-liquid molecular layers on the surface of ice could account for its slipperiness. Here, we assess the dominant hypotheses proposed to govern ice–skate friction and describe experiments conducted in an indoor skating rink aimed to provide observations to test these hypotheses. Our results indicate that the brittle failure of ice under rapid compression plays a strong role. Our observations did not confirm the presence of full-contact water films and are more consistent with the presence of lubricating ice-rich slurries at discontinuous high-pressure zones (HPZs). The presence of ice-rich slurries supporting skates through HPZs merges pressure-melting, abrasion and lubricating films as a unified hypothesis for why skates are so slippery across broad ranges of speeds, temperatures and normal loads. We suggest tribometer experiments to overcome the difficulties of investigating these processes during actual skating trials.


  • Open Access

    Assessing the Mechanisms Thought to Govern Ice and Snow Friction and Their Interplay With Substrate Brittle Behavior

    by James H. Lever, Emily Asenath-Smith, Susan Taylor, Austin P. Lines

    Sliding friction on ice and snow is characteristically low at temperatures common on Earth’s surface. This slipperiness underlies efficient sleds, winter sports, and the need for specialized tires. Friction can also play a micro-mechanical role affecting ice compressive and crushing strengths. Researchers have proposed several mechanisms thought to govern ice and snow friction, but directly validating the underlying mechanics has been difficult. This may be changing, as instruments capable of micro-scale measurements and imaging are now being brought to bear on friction studies. Nevertheless, given the broad regimes of practical interest (interaction length, temperature, speed, pressure, slider properties, etc.), it may be unrealistic to expect that a single mechanism accounts for why ice and snow are slippery. Because bulk ice, and the ice grains that constitute snow, are solids near their melting point at terrestrial temperatures, most research has focused on whether a lubricating water film forms at the interface with a slider. However, ice is extremely brittle, and dry-contact abrasion and wear at the front of sliders could prevent or delay a transition to lubricated contact. Also, water is a poor lubricant, and lubricating films thick enough to separate surface asperities may not form for many systems of interest. This article aims to assess our knowledge of the mechanics underlying ice and snow friction. We begin with a brief summary of the mechanical behavior of ice and snow substrates, behavior which perhaps has not received sufficient attention in friction studies. We then assess the strengths and weaknesses of five ice- and snow-friction hypotheses: pressure-melting, self-lubrication, quasi-liquid layers, abrasion, and ice-rich slurries. We discuss their assumptions and review evidence to determine whether they are consistent with the postulated mechanics. Lastly, we identify key issues that warrant additional research to resolve the specific mechanics and the transitions between them that control ice and snow friction across regimes of practical interest.


  • Open Access

    Why is Snow Slippery? The Role of Abrasion in Snow Kinetic Friction

    by James Lever, Susan Taylor, Garrett Hoch, Emily Asenath-Smith

    The mechanics of snow friction are central to competitive skiing, safe winter driving, avalanche dynamics, and efficient Polar sleds. For nearly 80 years, prevailing theory has postulated self-lubrication: dry-contact sliding warms snow-grains to the melting point, and further sliding produces melt-water that lubricates the interface. We recently published micro-scale interface observations that contradicted this explanation: contacting snow grains abraded and did not melt under a polyethylene slider, despite low friction values. We obtained coordinated infrared, visible-light, and scanning-electron micrographs that confirm that the evolving shapes observed during our tribometer tests are contacting snow grains polished by abrasion, and that the wear particles can sinter together and fill the adjacent pore spaces. Furthermore, dry-contact abrasive wear reasonably predicts the evolution of snow-slider contact area, and sliding-heat-source theory confirms that contact temperatures would not reach 0°C during our tribometer tests. Importantly, published measurements of interface temperatures also indicate that melting did not occur during field tests on sleds and skis. We postulate that abraded ice crystals form a dry-lubricant layer that makes contacting snow-grains slippery and are currently undertaking additional observations and theoretical analyses to assess this hypothesis.


  • Mobility Enhancement of Heavy-Duty Tracked Vehicles Under Load Using Real-Time Terrain Characterization, Traction Control, and a Towing Winch

    by Joshua T. Cook, Laura E. Ray, James H. Lever

    This paper presents a generalized, multibody dynamics model for a tracked vehicle equipped with a towing winch and control strategies that enhance vehicle mobility by regulating track slip based on real-time terrain characterization and automating winch use. The vehicle model is validated under conditions where no action is taken by the winch. Thereafter, two mobility enhancing control strategies are outlined. The first strategy regulates track slip to a real-time estimated value that generates maximum net traction. This is done by computing state-force estimates from a Kalman filter that are compared to terrain traction models using a Bayesian hypothesis selection approach. If the vehicle is traction limited and the first strategy fails, a second strategy that automates winch use is activated. Simulation results are shown for both scenarios.


  • Open Access

    Evidence that abrasion can govern snow kinetic friction

    by James H. Lever, Susan Taylor, Garrett R. Hoch, Charles Daghlian

    The long-accepted theory to explain why snow is slippery postulates self-lubrication: frictional heat from sliding melts and thereby lubricates the contacting snow grains. We recently published micro-scale interface observations that contradicted this explanation: contacting snow grains abraded and did not melt under a polyethylene slider, despite low friction values. Here we provide additional observational and theoretical evidence that abrasion can govern snow kinetic friction. We obtained coordinated infrared, visible-light and scanning-electron micrographs that confirm that the evolving shapes observed during our tribometer tests are contacting snow grains polished by abrasion, and that the wear particles can sinter together and fill the adjacent pore spaces. Furthermore, dry-contact abrasive wear reasonably predicts the evolution of snow-slider contact area, and sliding-heat-source theory confirms that contact temperatures would not reach 0°C during our tribometer tests. Importantly, published measurements of interface temperatures also indicate that melting did not occur during field tests on sleds and skis. Although prevailing theory anticipates a transition from dry to lubricated contact along a slider, we suggest that dry-contact abrasion and heat flow can prevent this transition from occurring for snow-friction scenarios of practical interest.


  • Open Access

    The mechanics of snow friction as revealed by micro-scale interface observations

    by James H. Lever, Susan Taylor, Arnold J. Song, Zoe R. Courville, Ross Lieblappen, Jason C. Weale

    The mechanics of snow friction are central to competitive skiing, safe winter driving and efficient polar sleds. For nearly 80 years, prevailing theory has postulated that self-lubrication accounts for low kinetic friction on snow: dry-contact sliding warms snow grains to the melting point, and further sliding produces meltwater layers that lubricate the interface. We sought to verify that self-lubrication occurs at the grain scale and to quantify the evolution of real contact area to aid modeling. We used high-resolution (15 µm) infrared thermography to observe the warming of stationary snow under a rotating polyethylene slider. Surprisingly, we did not observe melting at contacting snow grains despite low friction values. In some cases, slider shear failed inter-granular bonds and produced widespread snow movement with no persistent contacts to melt (μ < 0.03). When the snow grains did not move and persistent contacts evolved, the slider abraded rather than melted the grains at low resistance (μ < 0.05). Optical microscopy revealed that the abraded particles deposited in air pockets between grains and thereby carried heat away from the interface, a process not included in current models. Overall, our results challenge whether self-lubrication is indeed the dominant mechanism underlying low snow kinetic friction.