Ahmad Hadadpour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmad Hadadpour has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Mehdi Jangi
Lund University
4 shared publications - Shijie Xu
Shanghai Jiao Tong University
3 shared publications - Xue-Song Bai
Lund University
3 shared publications - Kar Mun Pang
Technical University of Denmark
2 shared publications Mehdi Jangi
2 shared publicationsXue-Song Bai
2 shared publications
Latest Publications
- Open Access
- 23 October 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (4) , 4889-4898
An extended FGM model with transported PDF for LES of spray combustion
- 23 October 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (4) , 4889-4898
Open AccessAn extended FGM model with transported PDF for LES of spray combustion
- Open Access
- 2 April 2022
- Published by Elsevier in Combustion and Flame
- Vol. 241
Effects of pre-injection on ignition, combustion and emissions of spray under engine-like conditions
- 2 April 2022
- Published by Elsevier in Combustion and Flame
- Vol. 241
Open AccessEffects of pre-injection on ignition, combustion and emissions of spray under engine-like conditions
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (4) , 4709-4716
The role of a split injection strategy in the mixture formation and combustion of diesel spray: A large-eddy simulation
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (4) , 4709-4716
The role of a split injection strategy in the mixture formation and combustion of diesel spray: A large-eddy simulation
- Open Access
- 24 April 2018
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 101 (4) , 1157-1171
The Effect of Splitting Timing on Mixing in a Jet with Double Injections
We present large-eddy simulation (LES) of a high-pressure gas jet that is injecting into a quiescent inert environment. The injection is through a nozzle with a diameter of 1.35 mm. Four injection strategies are considered in which the results of a single continuous injection case are compared with those of double injection cases with different injection splitting timing. In all double injection cases, the injection pulsing interval is kept the same, and the total injected mass is equal to that of the single injection case. On the other hand, the splitting timing is varied to investigate the effects of various injection splitting strategies on the mixture formation and the penetration length of the jet. Results show that the jet penetration length is not so sensitive to the splitting timing whereas the mixing quality can significantly change as a result of shifting the onset of injection splitting toward the end of injection. Especially, it is found that by adopting a post-injection strategy where a single injection splits into the main injection and late small injection near the end of injection period the mixing between the injected gas and ambient air is significantly improved. This trend is not as obvious when the injection splitting timing shifts toward the beginning or even in the middle of injection period. The increase of entrainment in the tail of each injection is one of the underlying physics in the mixing improvement in double injection cases. In addition to that, splitting a single injection into two smaller injections increases the surrounding area of the jet and also stretches it along the axial direction. It can potentially increase the mixing of injected gas with the ambient air.
- 24 April 2018
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 101 (4) , 1157-1171
Open AccessThe Effect of Splitting Timing on Mixing in a Jet with Double Injections
We present large-eddy simulation (LES) of a high-pressure gas jet that is injecting into a quiescent inert environment. The injection is through a nozzle with a diameter of 1.35 mm. Four injection strategies are considered in which the results of a single continuous injection case are compared with those of double injection cases with different injection splitting timing. In all double injection cases, the injection pulsing interval is kept the same, and the total injected mass is equal to that of the single injection case. On the other hand, the splitting timing is varied to investigate the effects of various injection splitting strategies on the mixture formation and the penetration length of the jet. Results show that the jet penetration length is not so sensitive to the splitting timing whereas the mixing quality can significantly change as a result of shifting the onset of injection splitting toward the end of injection. Especially, it is found that by adopting a post-injection strategy where a single injection splits into the main injection and late small injection near the end of injection period the mixing between the injected gas and ambient air is significantly improved. This trend is not as obvious when the injection splitting timing shifts toward the beginning or even in the middle of injection period. The increase of entrainment in the tail of each injection is one of the underlying physics in the mixing improvement in double injection cases. In addition to that, splitting a single injection into two smaller injections increases the surrounding area of the jet and also stretches it along the axial direction. It can potentially increase the mixing of injected gas with the ambient air.