Mehboob Rasul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mehboob Rasul has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Mohammed Maslehuddin
Applied Research Center for Metrology, Standards and Testing, King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia
2 shared publications- Saheed Kolawole Adekunle
King Fahd University of Petroleum and Minerals
2 shared publications Salah U. Al-Dulaijan
2 shared publications- Shamsad Ahmad
Civil and Environmental Engineering Department, King Fahd University of Petroleum & Minerals, Dhahran, Saudi Arabia
2 shared publications Syed Imran Ali
2 shared publicationsKhuyen Trong Hoang
Sumitomo Mitsui Construction Co., Ltd
1 shared publication
Latest Publications
- 1 June 2023
- Published by Springer Nature
- p. 1578-1588
Development of a Deep Learning-Based Anomaly Detection System for Structures
- 1 June 2023
- Published by Springer Nature
- p. 1578-1588
Development of a Deep Learning-Based Anomaly Detection System for Structures
- 5 February 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (10) , 12697-12709
Prediction of Strength of Plain and Blended Cement Concretes Cured Under Hot Weather Using Quadratic Regression and ANN Tools
- 5 February 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (10) , 12697-12709
Prediction of Strength of Plain and Blended Cement Concretes Cured Under Hot Weather Using Quadratic Regression and ANN Tools
- Top Cited Papers
- 1 July 2019
- Published by Elsevier in Composites Part B: Engineering
- Vol. 168, 291-301
Mechanical properties of steel fiber-reinforced UHPC mixtures exposed to elevated temperature: Effects of exposure duration and fiber content
- 1 July 2019
- Published by Elsevier in Composites Part B: Engineering
- Vol. 168, 291-301
Top Cited PapersMechanical properties of steel fiber-reinforced UHPC mixtures exposed to elevated temperature: Effects of exposure duration and fiber content
- 3 May 2019
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 48 (6) , 4355-4369
Evaluation of the Effect of Exposure Duration and Fiber Content on the Mechanical Properties of Polypropylene Fiber-Reinforced UHPC Exposed to Sustained Elevated Temperature
This article presents the results of an experimental study conducted to assess the effect of sustained elevated temperature on the mechanical properties of ultrahigh performance concrete (UHPC). UHPC mixtures were prepared with four different dosages of polypropylene (PP) fibers, and each mixture was exposed to a sustained pre-spalling elevated temperature of 300°C for five durations. The experimental data indicate that the used PP fibers were effective in providing sufficient strength and ductility to UHPC mixtures at room temperature. However, the PP fibers ceased to function as reinforcement in UHPC specimens that were exposed to the elevated temperature for 60 minutes. With an increase in the exposure period after melting of the fibers, the specimens exhibited a brittle mode of failure accompanied with an enhancement in the compressive strength and compressive modulus of toughness and a reduction in the modulus of elasticity and flexural strength. The significance of two variables (exposure duration and fiber content) was evaluated, and correlations between the mechanical properties and selected parameters were obtained by conducting a statistical analysis of the experimental data.
- 3 May 2019
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 48 (6) , 4355-4369
Evaluation of the Effect of Exposure Duration and Fiber Content on the Mechanical Properties of Polypropylene Fiber-Reinforced UHPC Exposed to Sustained Elevated Temperature
This article presents the results of an experimental study conducted to assess the effect of sustained elevated temperature on the mechanical properties of ultrahigh performance concrete (UHPC). UHPC mixtures were prepared with four different dosages of polypropylene (PP) fibers, and each mixture was exposed to a sustained pre-spalling elevated temperature of 300°C for five durations. The experimental data indicate that the used PP fibers were effective in providing sufficient strength and ductility to UHPC mixtures at room temperature. However, the PP fibers ceased to function as reinforcement in UHPC specimens that were exposed to the elevated temperature for 60 minutes. With an increase in the exposure period after melting of the fibers, the specimens exhibited a brittle mode of failure accompanied with an enhancement in the compressive strength and compressive modulus of toughness and a reduction in the modulus of elasticity and flexural strength. The significance of two variables (exposure duration and fiber content) was evaluated, and correlations between the mechanical properties and selected parameters were obtained by conducting a statistical analysis of the experimental data.