Honglei Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Honglei Sun has a total of 148 co-authors. Here are the top co-authors by number of shared publications:
- Yuanqiang Cai
Zhejiang University
16 shared publications - Hao Zhang
Nanyang Technological University
10 shared publications - Shan-Lin Xu
Zhejiang University of Technology
8 shared publications Yuanqiang Cai
College of Civil Engineering, Zhejiang University of Technology, Hangzhou, China
8 shared publications- Xueyu Geng
School of Engineering, University of Warwick, Coventry, UK
7 shared publications - Yuanqin Tao
Zhejiang University of Technology
7 shared publications
Latest Publications
- 10 October 2026
- Published by Elsevier in Transportation Geotechnics
- Vol. 67
Model uncertainty in finite element prediction of embankment settlement on soft soils
- 10 October 2026
- Published by Elsevier in Transportation Geotechnics
- Vol. 67
Model uncertainty in finite element prediction of embankment settlement on soft soils
- Open Access
- 7 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 321
Mapping Approaches for Assessing Regional Soil Liquefaction Potential: A Comparative Assessment
Seismic liquefaction poses a significant threat to infrastructure and human safety, making accurate regional-scale hazard assessment essential for effective disaster mitigation. This study systematically compares simple kriging (SK), ordinary kriging (OK), and sequential Gaussian simulation (SGS) for liquefaction potential mapping using a case study of the Chi-Chi earthquake. Results show that among the eight theoretical semivariogram models, the exponential model was identified as the optimal semivariogram model, showing the best fit and the lowest validation errors. SK and OK yield nearly identical LPI estimates with high accuracy and low computational cost, but oversmooth high-risk zones and underestimate spatial uncertainty. In contrast, SGS captures spatial heterogeneity and extreme values, with variance and coefficient of variation maps revealing higher and more heterogeneous uncertainties, which offers a more comprehensive basis for probabilistic risk assessment. However, these advantages came at a substantially higher computational cost. The choice of method should therefore depend on the engineering objective: kriging for rapid, large-scale trend estimation, and SGS for detailed probabilistic risk evaluation where capturing extreme values and uncertainty is critical.
- 7 August 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (8) , 321
Open AccessMapping Approaches for Assessing Regional Soil Liquefaction Potential: A Comparative Assessment
Seismic liquefaction poses a significant threat to infrastructure and human safety, making accurate regional-scale hazard assessment essential for effective disaster mitigation. This study systematically compares simple kriging (SK), ordinary kriging (OK), and sequential Gaussian simulation (SGS) for liquefaction potential mapping using a case study of the Chi-Chi earthquake. Results show that among the eight theoretical semivariogram models, the exponential model was identified as the optimal semivariogram model, showing the best fit and the lowest validation errors. SK and OK yield nearly identical LPI estimates with high accuracy and low computational cost, but oversmooth high-risk zones and underestimate spatial uncertainty. In contrast, SGS captures spatial heterogeneity and extreme values, with variance and coefficient of variation maps revealing higher and more heterogeneous uncertainties, which offers a more comprehensive basis for probabilistic risk assessment. However, these advantages came at a substantially higher computational cost. The choice of method should therefore depend on the engineering objective: kriging for rapid, large-scale trend estimation, and SGS for detailed probabilistic risk evaluation where capturing extreme values and uncertainty is critical.
- 27 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 365
A CPTU-based marine soil stratification method considering classification probability
- 27 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 365
A CPTU-based marine soil stratification method considering classification probability
- Open Access
- 17 July 2026
- Published by MDPI AG in Geotechnics
- Vol. 6 (3) , 66
Calibration Chamber Test of CPT Penetration Based on Marine Sand with Parameter Interpretation Models
This study investigates marine sand collected from the southeastern coast of China through laboratory calibration chamber model tests under varying relative densities and consolidation stresses. The consolidation characteristics and cone penetration test (CPT) penetration response of soil specimens were examined, and interpretation models relating CPT parameters to soil unit weight, relative density, and shear wave velocity were established. Results show that shear wave velocity increases with relative density, with consolidation exerting a stronger enhancement. Lateral earth pressure exhibits a pronounced distance attenuation effect, with stress differences most prominent near-field and diminishing with distance. Cone tip resistance increases with both relative density and consolidation stress, with consolidation stress exerting a more significant influence on low-density specimens; sleeve friction increases linearly with relative density. The interpretation models achieve good correlations with unit weight (R2 = 0.78), normalized cone tip resistance with the square of relative density (R2 = 0.72), and shear wave velocity (R2 = 0.85), and field validation confirms higher prediction accuracy than conventional empirical formulas for terrigenous sands. The models enable rapid, cost-effective parameter estimation from routine CPT data, though they remain site-specific, being based on nine chamber tests and validated against six field layers from a single site.
- 17 July 2026
- Published by MDPI AG in Geotechnics
- Vol. 6 (3) , 66
Open AccessCalibration Chamber Test of CPT Penetration Based on Marine Sand with Parameter Interpretation Models
This study investigates marine sand collected from the southeastern coast of China through laboratory calibration chamber model tests under varying relative densities and consolidation stresses. The consolidation characteristics and cone penetration test (CPT) penetration response of soil specimens were examined, and interpretation models relating CPT parameters to soil unit weight, relative density, and shear wave velocity were established. Results show that shear wave velocity increases with relative density, with consolidation exerting a stronger enhancement. Lateral earth pressure exhibits a pronounced distance attenuation effect, with stress differences most prominent near-field and diminishing with distance. Cone tip resistance increases with both relative density and consolidation stress, with consolidation stress exerting a more significant influence on low-density specimens; sleeve friction increases linearly with relative density. The interpretation models achieve good correlations with unit weight (R2 = 0.78), normalized cone tip resistance with the square of relative density (R2 = 0.72), and shear wave velocity (R2 = 0.85), and field validation confirms higher prediction accuracy than conventional empirical formulas for terrigenous sands. The models enable rapid, cost-effective parameter estimation from routine CPT data, though they remain site-specific, being based on nine chamber tests and validated against six field layers from a single site.
- Open Access
- 3 July 2026
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
Salinity-enhanced electroosmotic permeability mediated by soil electrical conductivity
- 3 July 2026
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
Open AccessSalinity-enhanced electroosmotic permeability mediated by soil electrical conductivity
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-18
Vacuum consolidation of clayey slurries with evolving heterogeneous and irregular clogging
Clogging is widely recognized as a critical factor limiting the vacuum consolidation efficiency, yet the underlying mechanisms remain insufficiently understood, particularly in horizontally drained systems where gravity induces anisotropic clogging evolution. Motivated by experimental evidence of particle relative migration and grading variation during vacuum consolidation, this study develops a two-dimensional large-strain consolidation model that incorporates heterogeneous and irregular clogging zone expansion by adopting zone-specific compression and permeability indices. The numerical solutions obtained through the alternative direction implicit scheme are verified against an established one-dimensional model for layered soil and two laboratory model tests. Parametric analyses reveal that vacuum-induced heterogeneity dominates clogging, typically causing opposite changes in compressibility and permeability in the finer (i.e., higher fines content) and coarser subsections of the clogging zone. The finer subsection adjacent to the drain generally governs and delays the overall consolidation. Irregularity of the clogging zone manifests as disparities in both maximum radius and growth rate between the vertical and horizontal directions, with the maximum radius influencing the entire consolidation process and the growth rate affecting primarily the early stages. Moreover, clogging effects are intensified by larger drain spacing, higher initial water content, or lower initial permeability.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-18
Vacuum consolidation of clayey slurries with evolving heterogeneous and irregular clogging
Clogging is widely recognized as a critical factor limiting the vacuum consolidation efficiency, yet the underlying mechanisms remain insufficiently understood, particularly in horizontally drained systems where gravity induces anisotropic clogging evolution. Motivated by experimental evidence of particle relative migration and grading variation during vacuum consolidation, this study develops a two-dimensional large-strain consolidation model that incorporates heterogeneous and irregular clogging zone expansion by adopting zone-specific compression and permeability indices. The numerical solutions obtained through the alternative direction implicit scheme are verified against an established one-dimensional model for layered soil and two laboratory model tests. Parametric analyses reveal that vacuum-induced heterogeneity dominates clogging, typically causing opposite changes in compressibility and permeability in the finer (i.e., higher fines content) and coarser subsections of the clogging zone. The finer subsection adjacent to the drain generally governs and delays the overall consolidation. Irregularity of the clogging zone manifests as disparities in both maximum radius and growth rate between the vertical and horizontal directions, with the maximum radius influencing the entire consolidation process and the growth rate affecting primarily the early stages. Moreover, clogging effects are intensified by larger drain spacing, higher initial water content, or lower initial permeability.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-20
Consolidation behavior of geotextile-assisted vacuum preloading for dredged soil
Vacuum preloading combined with horizontal drains has been increasingly applied to improve dredged soils. This study proposes a novel vacuum preloading method in which geotextiles are used directly as horizontal drains. Four model tests were conducted to evaluate the feasibility and consolidation mechanism in comparison with prefabricated horizontal drain (PHD) vacuum preloading. The results show that vacuum pressure was rapidly transmitted along the geotextile, reaching 87.6%–94.9% of the applied vacuum pressure at the geotextile surface in the initial stage and remaining at approximately 92% at later stages. The degree of consolidation reached about 90%, exceeding that obtained using a single PHD. Non-uniform consolidation was observed, with a vacuum loss of approximately 20 kPa at 20 cm from the geotextile. After treatment, the water content and vane shear strength near the geotextile reached approximately 44% and 45 kPa, respectively. Particle image velocimetry revealed predominantly vertical compression with negligible horizontal strain, indicating that the consolidation can be reasonably approximated as one-dimensional. Scanning electron microscopy showed reduced fine-particle intrusion into the geotextile due to its lower unit-area water flux. A double-layer consolidation model was introduced to predict the consolidation degree, and showed good agreement with the experimental measurements.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-20
Consolidation behavior of geotextile-assisted vacuum preloading for dredged soil
Vacuum preloading combined with horizontal drains has been increasingly applied to improve dredged soils. This study proposes a novel vacuum preloading method in which geotextiles are used directly as horizontal drains. Four model tests were conducted to evaluate the feasibility and consolidation mechanism in comparison with prefabricated horizontal drain (PHD) vacuum preloading. The results show that vacuum pressure was rapidly transmitted along the geotextile, reaching 87.6%–94.9% of the applied vacuum pressure at the geotextile surface in the initial stage and remaining at approximately 92% at later stages. The degree of consolidation reached about 90%, exceeding that obtained using a single PHD. Non-uniform consolidation was observed, with a vacuum loss of approximately 20 kPa at 20 cm from the geotextile. After treatment, the water content and vane shear strength near the geotextile reached approximately 44% and 45 kPa, respectively. Particle image velocimetry revealed predominantly vertical compression with negligible horizontal strain, indicating that the consolidation can be reasonably approximated as one-dimensional. Scanning electron microscopy showed reduced fine-particle intrusion into the geotextile due to its lower unit-area water flux. A double-layer consolidation model was introduced to predict the consolidation degree, and showed good agreement with the experimental measurements.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-10
Boundary condition for soil–atmosphere interfaces in vacuum consolidation modeling
The boundary condition at soil–atmosphere interfaces of vacuum-preloaded soil remains an open issue. Based on a newly developed model that considers the final absolute excess pore-water pressure at the permeable boundary as the original critical air entry value (CAEV), rather than zero as assumed in traditional models, an extended model is proposed in this study accounting for the total stress (i.e., the sum of surcharge, hydrostatic pressure, and self-weight of soil). The determination methods and difference between the original and actual CAEVs are elucidated through the relationships among the void ratio–effective stress ( e– σ′), void ratio–suction ( e– ψ), and void ratio–air entry value ( e–AEV) curves, and the validity of the proposed model is verified via three laboratory tests. It appears that the actual CAEV is greater than the original CAEV, implying a larger final mean effective stress of soil. Their difference magnifies as the total stress increases. Further analysis shows that the subsequent air entry behavior of the inner soil layers differs significantly between the scenarios with an upper and a lower open surface, due to the varying suctions and CAEVs at different soil positions.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-10
Boundary condition for soil–atmosphere interfaces in vacuum consolidation modeling
The boundary condition at soil–atmosphere interfaces of vacuum-preloaded soil remains an open issue. Based on a newly developed model that considers the final absolute excess pore-water pressure at the permeable boundary as the original critical air entry value (CAEV), rather than zero as assumed in traditional models, an extended model is proposed in this study accounting for the total stress (i.e., the sum of surcharge, hydrostatic pressure, and self-weight of soil). The determination methods and difference between the original and actual CAEVs are elucidated through the relationships among the void ratio–effective stress ( e– σ′), void ratio–suction ( e– ψ), and void ratio–air entry value ( e–AEV) curves, and the validity of the proposed model is verified via three laboratory tests. It appears that the actual CAEV is greater than the original CAEV, implying a larger final mean effective stress of soil. Their difference magnifies as the total stress increases. Further analysis shows that the subsequent air entry behavior of the inner soil layers differs significantly between the scenarios with an upper and a lower open surface, due to the varying suctions and CAEVs at different soil positions.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-16
A validated two-phase flow model for characterizing the coupled sedimentation and self-weight consolidation of slurries
Self-weight sedimentation and consolidation of slurries are common phenomena in natural and geotechnical systems, including dredging and land reclamation projects. As the coupled nature of suspension settling and sediment bed consolidation, predicting sediment evolution is challenging. To address this complexity, this study presents a modified Eulerian two-phase flow model derived from Navier–Stokes equations and systematic experiments to establish unified constitutive relationships across different physical states. Particle–fluid interaction forces in both suspension and solid sediment bed regimes were quantified through settling and permeability tests, incorporating gel point continuity constraints. Sediment bed’s compressibility was determined using solid concentration-effective stress relationship obtained from oedometer testing. The proposed model demonstrated good agreement with full sedimentation–consolidation experiments across various initial concentrations. Simulations revealed two distinct settling behaviors governed by initial concentration relative to the gel point: sub-gel slurries develop supernatant–suspension interfaces controlled by hindered settling, while super-gel systems form supernatant–sediment bed interfaces dominated by consolidation. Initial slurry height influenced self-weight stresses, directly affecting sediment bed concentration profiles and normalized heights. This framework successfully integrates sedimentation–consolidation dynamics, captures spatiotemporal evolution of concentration and stress fields, and enables the quantitative identification of phase regime transitions in multiphase particulate flows.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-16
A validated two-phase flow model for characterizing the coupled sedimentation and self-weight consolidation of slurries
Self-weight sedimentation and consolidation of slurries are common phenomena in natural and geotechnical systems, including dredging and land reclamation projects. As the coupled nature of suspension settling and sediment bed consolidation, predicting sediment evolution is challenging. To address this complexity, this study presents a modified Eulerian two-phase flow model derived from Navier–Stokes equations and systematic experiments to establish unified constitutive relationships across different physical states. Particle–fluid interaction forces in both suspension and solid sediment bed regimes were quantified through settling and permeability tests, incorporating gel point continuity constraints. Sediment bed’s compressibility was determined using solid concentration-effective stress relationship obtained from oedometer testing. The proposed model demonstrated good agreement with full sedimentation–consolidation experiments across various initial concentrations. Simulations revealed two distinct settling behaviors governed by initial concentration relative to the gel point: sub-gel slurries develop supernatant–suspension interfaces controlled by hindered settling, while super-gel systems form supernatant–sediment bed interfaces dominated by consolidation. Initial slurry height influenced self-weight stresses, directly affecting sediment bed concentration profiles and normalized heights. This framework successfully integrates sedimentation–consolidation dynamics, captures spatiotemporal evolution of concentration and stress fields, and enables the quantitative identification of phase regime transitions in multiphase particulate flows.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-24
Multi-stage and multi-objective optimization framework for servo-controlled wall deflection during deep excavation
Controlling excavation-induced deformation is essential for excavation safety and adjacent structure protection. To address the increasingly stringent deformation control requirements driven by growing building density in urban areas, this study proposes a multi-stage and multi-objective optimization framework for servo-controlled wall deflection during deep excavations. First, since the servo force optimization involves thousands of deflection evaluations, a pretrained surrogate model is developed to accelerate this computationally intensive process. Subsequently, a primary–secondary loss formulation is defined, with deformation control as the primary goal and unloading minimization as a secondary objective for stability. Finally, this formulation is optimized using a cross-stage coordinated algorithm. Unlike existing methods that treat stages independently, the proposed algorithm employs beam search to evolve top-ranked solutions in parallel, yielding globally optimal servo force configurations. A deep excavation project in Ningbo, China is used for illustration. The proposed surrogate model outperforms alternative approaches, achieving R 2 values above 0.95 across all stages. With a 10% unloading ratio, the optimization reduces the maximum wall deflection at each stage by approximately 30%–35%, demonstrating effective deformation control. For stricter requirements, a higher allowable unloading ratio can be adopted, potentially limiting deflection to within 0.2% of the excavation depth.
- 1 January 2026
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 63, 1-24
Multi-stage and multi-objective optimization framework for servo-controlled wall deflection during deep excavation
Controlling excavation-induced deformation is essential for excavation safety and adjacent structure protection. To address the increasingly stringent deformation control requirements driven by growing building density in urban areas, this study proposes a multi-stage and multi-objective optimization framework for servo-controlled wall deflection during deep excavations. First, since the servo force optimization involves thousands of deflection evaluations, a pretrained surrogate model is developed to accelerate this computationally intensive process. Subsequently, a primary–secondary loss formulation is defined, with deformation control as the primary goal and unloading minimization as a secondary objective for stability. Finally, this formulation is optimized using a cross-stage coordinated algorithm. Unlike existing methods that treat stages independently, the proposed algorithm employs beam search to evolve top-ranked solutions in parallel, yielding globally optimal servo force configurations. A deep excavation project in Ningbo, China is used for illustration. The proposed surrogate model outperforms alternative approaches, achieving R 2 values above 0.95 across all stages. With a 10% unloading ratio, the optimization reduces the maximum wall deflection at each stage by approximately 30%–35%, demonstrating effective deformation control. For stricter requirements, a higher allowable unloading ratio can be adopted, potentially limiting deflection to within 0.2% of the excavation depth.