Hasbuna Kamila
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hasbuna Kamila has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Johannes de Boor
German Aerospace Center (DLR)
10 shared publications - Aryan Sankhla
Institute of Materials Research German Aerospace Center (DLR) D–51147 Cologne Germany
7 shared publications Eckhard Mueller
German Aerospace Center (DLR), Institute of Materials Research, Cologne, Germany
7 shared publications- Mohammad Yasseri
Institute for Frontier Materials on Earth and in Space, German Aerospace Center (DLR), D-51147 Cologne, Germany
4 shared publications E. Müller
German Aerospace Center, Linder Hoehe, Koln, Nordrhein-Westfalen, 51147, GERMANY
2 shared publicationsLéo Millerand
German Aerospace Center (DLR), Institute of Materials Research, Cologne, Germany
2 shared publications
Latest Publications
- Open Access
- 30 September 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (40) , 21716-21726
Establishing synthesis–composition–property relationships for enhanced and reproducible thermoelectric properties of MgAgSb
α-MgAgSb is a promising p-type thermoelectric (TE) with excellent performance from room temperature up to 300 °C with a figure of merit of zTmax = 1.3. This makes MgAgSb a potential Te-free bismuth telluride (Bi2Te3) substitute for cooling and waste heat conversion applications. However, the material is also known for its sensitivity on synthesis conditions as indicated by various reports on the same nominal composition which show greatly differing TE properties and performance. This indicates a fundamental lack of synthesis control and synthesis–composition–property relationship knowledge. In this work, we establish a modified synthesis route with improved control over the effective sample stoichiometry which allows for reproducible high-performance properties (zTmax = 1.34 ± 0.19 at 561 K) and for systematically targeting different thermodynamic states of MgAgSb. This phase boundary mapping reveals that the homogeneity range for MgAgSb is very small (<0.1 at%) and that the TE properties are not governed by different thermodynamic states. Instead, we rationalize that the TE performance of MgAgSb is mainly controlled by the amount and type of secondary phases, mainly affecting the carrier mobility. We conclude that Sb-excess related secondary phases are the least detrimental, leading the way to upscaled synthesis of high-performance material.
- 30 September 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (40) , 21716-21726
Open AccessEstablishing synthesis–composition–property relationships for enhanced and reproducible thermoelectric properties of MgAgSb
α-MgAgSb is a promising p-type thermoelectric (TE) with excellent performance from room temperature up to 300 °C with a figure of merit of zTmax = 1.3. This makes MgAgSb a potential Te-free bismuth telluride (Bi2Te3) substitute for cooling and waste heat conversion applications. However, the material is also known for its sensitivity on synthesis conditions as indicated by various reports on the same nominal composition which show greatly differing TE properties and performance. This indicates a fundamental lack of synthesis control and synthesis–composition–property relationship knowledge. In this work, we establish a modified synthesis route with improved control over the effective sample stoichiometry which allows for reproducible high-performance properties (zTmax = 1.34 ± 0.19 at 561 K) and for systematically targeting different thermodynamic states of MgAgSb. This phase boundary mapping reveals that the homogeneity range for MgAgSb is very small (<0.1 at%) and that the TE properties are not governed by different thermodynamic states. Instead, we rationalize that the TE performance of MgAgSb is mainly controlled by the amount and type of secondary phases, mainly affecting the carrier mobility. We conclude that Sb-excess related secondary phases are the least detrimental, leading the way to upscaled synthesis of high-performance material.
- Open Access
- 1 June 2022
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 4 (3) , 035001
Understanding the dopability of p-type Mg2(Si,Sn) by relating hybrid-density functional calculation results to experimental data
It is crucial to reach a sufficiently high carrier concentration in order to optimize the thermoelectric (TE) material in the development of Mg2X(X= Si, Ge, and Sn)-based TE generators. While n-type Mg2(Si,Sn) has excellent TE properties, p-type shows suboptimal TE performance because of insufficient carrier concentration, in particular for Mg2Si and Si-rich Mg2(Si,Sn). A systematic investigation of Li-doped Mg2Si1-xSnxhas been performed as Li, in contrast to other typical dopants, has a high solubility in the material system and has been shown to yield the highest reported carrier concentrations. We observe that the carrier concentration increases with Li content, but the dopant efficiency decreases. With respect to the Si:Sn ratio, we find a clear increase in maximum achievable carrier concentration and dopant efficiency with increasing Sn content. The trends can be understood by employing defect formation energies obtained within the hybrid-density functional theory (DFT) for the binaries. Further, we use a linear interpolation of the hybrid-DFT results from the binaries to the ternary Mg2(Si,Sn) compositions and a simple single parabolic band model to predict the maximal achievable carrier concentration for the solid solutions, providing a simple guideline for experimental work. Finally, we show that the approach is transferable to other material classes. This work highlights that, besides dopant solubility, the interplay between intrinsic and extrinsic defects determines the achievable carrier concentration.
- 1 June 2022
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 4 (3) , 035001
Open AccessUnderstanding the dopability of p-type Mg2(Si,Sn) by relating hybrid-density functional calculation results to experimental data
It is crucial to reach a sufficiently high carrier concentration in order to optimize the thermoelectric (TE) material in the development of Mg2X(X= Si, Ge, and Sn)-based TE generators. While n-type Mg2(Si,Sn) has excellent TE properties, p-type shows suboptimal TE performance because of insufficient carrier concentration, in particular for Mg2Si and Si-rich Mg2(Si,Sn). A systematic investigation of Li-doped Mg2Si1-xSnxhas been performed as Li, in contrast to other typical dopants, has a high solubility in the material system and has been shown to yield the highest reported carrier concentrations. We observe that the carrier concentration increases with Li content, but the dopant efficiency decreases. With respect to the Si:Sn ratio, we find a clear increase in maximum achievable carrier concentration and dopant efficiency with increasing Sn content. The trends can be understood by employing defect formation energies obtained within the hybrid-density functional theory (DFT) for the binaries. Further, we use a linear interpolation of the hybrid-DFT results from the binaries to the ternary Mg2(Si,Sn) compositions and a simple single parabolic band model to predict the maximal achievable carrier concentration for the solid solutions, providing a simple guideline for experimental work. Finally, we show that the approach is transferable to other material classes. This work highlights that, besides dopant solubility, the interplay between intrinsic and extrinsic defects determines the achievable carrier concentration.
- Open Access
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 3 (4) , 044006
Efficiency as a performance metric for material optimization in thermoelectric generators
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 3 (4) , 044006
Open AccessEfficiency as a performance metric for material optimization in thermoelectric generators
- 19 May 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (6) , 5533-5542
Optimization of the Thermoelectric Properties of p-Type Mg2–yLiyGe1–xSnx and Mg2–yLiyGe1–zSiz with x, z = 0.1 and 0.2
- 19 May 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (6) , 5533-5542
Optimization of the Thermoelectric Properties of p-Type Mg2–yLiyGe1–xSnx and Mg2–yLiyGe1–zSiz with x, z = 0.1 and 0.2
- 1 October 2020
- Published by Elsevier in Acta Materialia
- Vol. 199, 85-95
Analyzing thermoelectric transport in n-type Mg2Si0.4Sn0.6 and correlation with microstructural effects: An insight on the role of Mg
- 1 October 2020
- Published by Elsevier in Acta Materialia
- Vol. 199, 85-95
Analyzing thermoelectric transport in n-type Mg2Si0.4Sn0.6 and correlation with microstructural effects: An insight on the role of Mg
- Open Access
- 30 April 2020
- Published by Wiley in Advanced Science
- Vol. 7 (12) , 2000070
Non‐Rigid Band Structure in Mg2Ge for Improved Thermoelectric Performance
Magnesium silicide and its solid solutions are among the most attractive materials for thermoelectric generators in the temperature range of 500–800 K. However, while n‐type Mg2(Si,Ge,Sn) materials show excellent thermoelectric performance, the corresponding p‐type solid solutions are still inferior, mainly due to less favorable properties of the valence bands compared to the conduction bands. Here, Li doped Mg2Ge with a thermoelectric figure of merit zT of 0.5 at 700 K is reported, which is four times higher than that of p‐type Mg2Si and double than that of p‐type Mg2Sn. The reason for the excellent properties is an unusual temperature dependence of Seebeck coefficient and electrical conductivity compared to a standard highly doped semiconductor. The properties cannot be captured assuming a rigid band structure but well reproduced assuming two parabolic valence bands with a strong temperature dependent interband separation. According to the analysis, the difference in energy between the two bands decrease with temperature, leading to a band convergence at around 650 K and finally to an inversion of the band positions. The finding of a combination of a light and a heavy band that are non‐rigid with temperature can pave the way for further optimization of p‐type Mg2(Si,Ge,Sn).
- 30 April 2020
- Published by Wiley in Advanced Science
- Vol. 7 (12) , 2000070
Open AccessNon‐Rigid Band Structure in Mg2Ge for Improved Thermoelectric Performance
Magnesium silicide and its solid solutions are among the most attractive materials for thermoelectric generators in the temperature range of 500–800 K. However, while n‐type Mg2(Si,Ge,Sn) materials show excellent thermoelectric performance, the corresponding p‐type solid solutions are still inferior, mainly due to less favorable properties of the valence bands compared to the conduction bands. Here, Li doped Mg2Ge with a thermoelectric figure of merit zT of 0.5 at 700 K is reported, which is four times higher than that of p‐type Mg2Si and double than that of p‐type Mg2Sn. The reason for the excellent properties is an unusual temperature dependence of Seebeck coefficient and electrical conductivity compared to a standard highly doped semiconductor. The properties cannot be captured assuming a rigid band structure but well reproduced assuming two parabolic valence bands with a strong temperature dependent interband separation. According to the analysis, the difference in energy between the two bands decrease with temperature, leading to a band convergence at around 650 K and finally to an inversion of the band positions. The finding of a combination of a light and a heavy band that are non‐rigid with temperature can pave the way for further optimization of p‐type Mg2(Si,Ge,Sn).
- 1 February 2020
- Published by Elsevier in Acta Materialia
- Vol. 185, 80-88
Solid solution formation in Mg2(Si,Sn) and shape of the miscibility gap
- 1 February 2020
- Published by Elsevier in Acta Materialia
- Vol. 185, 80-88
Solid solution formation in Mg2(Si,Sn) and shape of the miscibility gap
- 11 June 2019
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 125 (22) , 225103
Experimental investigation of the predicted band structure modification of Mg2X (X: Si, Sn) thermoelectric materials due to scandium addition
Modification of the electronic band structure via doping is an effective way to improve the thermoelectric properties of a material. Theoretical calculations from a previous study have predicted that Sc substitution on the Mg site in Mg2X materials drastically increase their Seebeck coefficient. Herein, we experimentally studied the influence of scandium substitution on the thermoelectric properties of Mg2Si0.4Sn0.6 and Mg2Sn. We found that the thermoelectric properties of these materials are unaffected by Sc addition, and we did not find hints for a modification of the electronic band structure. The SEM-energy dispersive X-ray analysis revealed that the scandium does not substitute Mg but forms a secondary phase (Sc-Si) in Mg2Si0.4Sn0.6 and remains inert in Mg2Sn, respectively. Thus, this study proves that scandium is an ineffective dopant for Mg2X materials.
- 11 June 2019
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 125 (22) , 225103
Experimental investigation of the predicted band structure modification of Mg2X (X: Si, Sn) thermoelectric materials due to scandium addition
Modification of the electronic band structure via doping is an effective way to improve the thermoelectric properties of a material. Theoretical calculations from a previous study have predicted that Sc substitution on the Mg site in Mg2X materials drastically increase their Seebeck coefficient. Herein, we experimentally studied the influence of scandium substitution on the thermoelectric properties of Mg2Si0.4Sn0.6 and Mg2Sn. We found that the thermoelectric properties of these materials are unaffected by Sc addition, and we did not find hints for a modification of the electronic band structure. The SEM-energy dispersive X-ray analysis revealed that the scandium does not substitute Mg but forms a secondary phase (Sc-Si) in Mg2Si0.4Sn0.6 and remains inert in Mg2Sn, respectively. Thus, this study proves that scandium is an ineffective dopant for Mg2X materials.
- Open Access
Insight on the Interplay between Synthesis Conditions and Thermoelectric Properties of α-MgAgSb
α-MgAgSb is a very promising thermoelectric material with excellent thermoelectric properties between room temperature and 300 °C, a range where few other thermoelectric materials show good performance. Previous reports rely on a two-step ball-milling process and/or time-consuming annealing. Aiming for a faster and scalable fabrication route, herein, we investigated other potential synthesis routes and their impact on the thermoelectric properties of α-MgAgSb. We started from a gas-atomized MgAg precursor and employed ball-milling only in the final mixing step. Direct comparison of high energy ball-milling and planetary ball-milling revealed that high energy ball milling already induced formation of MgAgSb, while planetary ball milling did not. This had a strong impact on the microstructure and secondary phase fraction, resulting in superior performance of the high energy ball milling route with an attractive average thermoelectric figure of merit of 0.9. We also show that the formation of undesired secondary phases cannot be avoided by a modification of the sintering temperature after planetary ball milling, and discuss the influence of commonly observed secondary phases on the carrier mobility and on the thermoelectric properties of α-MgAgSb.Open AccessInsight on the Interplay between Synthesis Conditions and Thermoelectric Properties of α-MgAgSb
α-MgAgSb is a very promising thermoelectric material with excellent thermoelectric properties between room temperature and 300 °C, a range where few other thermoelectric materials show good performance. Previous reports rely on a two-step ball-milling process and/or time-consuming annealing. Aiming for a faster and scalable fabrication route, herein, we investigated other potential synthesis routes and their impact on the thermoelectric properties of α-MgAgSb. We started from a gas-atomized MgAg precursor and employed ball-milling only in the final mixing step. Direct comparison of high energy ball-milling and planetary ball-milling revealed that high energy ball milling already induced formation of MgAgSb, while planetary ball milling did not. This had a strong impact on the microstructure and secondary phase fraction, resulting in superior performance of the high energy ball milling route with an attractive average thermoelectric figure of merit of 0.9. We also show that the formation of undesired secondary phases cannot be avoided by a modification of the sintering temperature after planetary ball milling, and discuss the influence of commonly observed secondary phases on the carrier mobility and on the thermoelectric properties of α-MgAgSb. - 28 November 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (3) , 1045-1054
Analyzing transport properties of p-type Mg2Si–Mg2Sn solid solutions: optimization of thermoelectric performance and insight into the electronic band structure
Figure of merit zT mapping of p-Mg2Si1−xSnx with respect to carrier concentration.
- 28 November 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (3) , 1045-1054
Analyzing transport properties of p-type Mg2Si–Mg2Sn solid solutions: optimization of thermoelectric performance and insight into the electronic band structure
Figure of merit zT mapping of p-Mg2Si1−xSnx with respect to carrier concentration.