Zhibin Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhibin Lin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alexey N. Volkov
Department of Mechanical Engineering, University of Alabama , 7th Avenue, Tuscaloosa, Alabama 35487
4 shared publications - Omid A. Ranjbar
Department of Mechanical Engineering, University of Alabama 2 , 7th Avenue, Tuscaloosa, Alabama 35487, USA
4 shared publications - Hisashi Matsumoto
MKS Instruments, Inc. (United States)
3 shared publications - Jan Kleinert
Photonics Solutions Division, MKS Instruments, Inc., Beaverton, USA
3 shared publications - Joel N. Schrauben
Photonics Solutions Division, MKS Instruments, Inc., Beaverton, USA
3 shared publications - Austin Palya
Univ Alabama, Dept Mech Engn, 7th Ave, Tuscaloosa, AL 35487 USA
2 shared publications
Latest Publications
- 8 March 2022
- Published by Springer Nature in Applied Physics A
- Vol. 128 (4) , 1-10
Rapid formation of high aspect ratio through holes in thin glass substrates using an engineered, QCW laser approach
- 8 March 2022
- Published by Springer Nature in Applied Physics A
- Vol. 128 (4) , 1-10
Rapid formation of high aspect ratio through holes in thin glass substrates using an engineered, QCW laser approach
- 8 July 2021
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 33 (3) , 032010
Ultrafast laser ablation of silicon with ∼GHz bursts
The authors report on processing silicon with bursts of hundreds of subpicosecond pulses with an intraburst pulse repetition frequency of 0.86 GHz at 515 nm. They find that the burst-to-burst overlap is a key parameter in optimizing the ablation efficiency for the line scribing and milling processes, contrary to traditional nonburst ultrafast processes. A nanosecond laser reference experiment and the corresponding multiphase simulations demonstrate that this behavior is directly related to the hydrodynamic effects of the molten material generated during the laser processing. Exploring the hole and scribe morphology with scanning transmission electron microscopy and selective area electron diffraction yields a surprise: holes show no sign of a polycrystalline or amorphous heat affected zone, while scribed lines clearly do. The multiphase modeling provides a likely explanation—it is not “ablation cooling.”
- 8 July 2021
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 33 (3) , 032010
Ultrafast laser ablation of silicon with ∼GHz bursts
The authors report on processing silicon with bursts of hundreds of subpicosecond pulses with an intraburst pulse repetition frequency of 0.86 GHz at 515 nm. They find that the burst-to-burst overlap is a key parameter in optimizing the ablation efficiency for the line scribing and milling processes, contrary to traditional nonburst ultrafast processes. A nanosecond laser reference experiment and the corresponding multiphase simulations demonstrate that this behavior is directly related to the hydrodynamic effects of the molten material generated during the laser processing. Exploring the hole and scribe morphology with scanning transmission electron microscopy and selective area electron diffraction yields a surprise: holes show no sign of a polycrystalline or amorphous heat affected zone, while scribed lines clearly do. The multiphase modeling provides a likely explanation—it is not “ablation cooling.”
- Open Access
- 12 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (22) , 223105
Plume accumulation effect and interaction of plumes induced by irradiation of a copper target with a burst of nanosecond laser pulses near the ionization threshold
The interaction between plumes induced by irradiation of a copper target in argon background gas with a burst of nanosecond laser pulses is studied numerically. The two-dimensional (2D) simulations are performed based on a model that includes a thermal model of the irradiated target and a kinetic model of plume expansion. The latter is implemented in the form of the direct simulation Monte Carlo method, where the equilibrium ionization and absorption of laser radiation are considered. For the laser spot diameter varying from 20 μm to 200 μm, the 2D plume structure is found to be different from the structure predicted by a one-dimensional model. The simulations reveal a strong plume accumulation effect when the plumes generated by preceding pulses in a burst change the conditions of propagation for plumes induced by subsequent pulses. The inter-plume interaction can result in merging shock waves induced by individual pulses and formation of a single plume. The degree of plume accumulation depends on the inter-pulse separation, laser spot diameter, background gas pressure, and number of pulses. When the irradiation conditions for a single pulse are below the ionization threshold, the conditions of plasma ignition can be reached by increasing the number of laser pulses due to the plume accumulation effect. This results in plasma shielding and reduction of the effectiveness of material removal by the subsequent pulses in the burst. The plume accumulation effect, thus, determines the optimum number of pulses in the burst in applications of laser ablation for material removal.
- 12 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (22) , 223105
Open AccessPlume accumulation effect and interaction of plumes induced by irradiation of a copper target with a burst of nanosecond laser pulses near the ionization threshold
The interaction between plumes induced by irradiation of a copper target in argon background gas with a burst of nanosecond laser pulses is studied numerically. The two-dimensional (2D) simulations are performed based on a model that includes a thermal model of the irradiated target and a kinetic model of plume expansion. The latter is implemented in the form of the direct simulation Monte Carlo method, where the equilibrium ionization and absorption of laser radiation are considered. For the laser spot diameter varying from 20 μm to 200 μm, the 2D plume structure is found to be different from the structure predicted by a one-dimensional model. The simulations reveal a strong plume accumulation effect when the plumes generated by preceding pulses in a burst change the conditions of propagation for plumes induced by subsequent pulses. The inter-plume interaction can result in merging shock waves induced by individual pulses and formation of a single plume. The degree of plume accumulation depends on the inter-pulse separation, laser spot diameter, background gas pressure, and number of pulses. When the irradiation conditions for a single pulse are below the ionization threshold, the conditions of plasma ignition can be reached by increasing the number of laser pulses due to the plume accumulation effect. This results in plasma shielding and reduction of the effectiveness of material removal by the subsequent pulses in the burst. The plume accumulation effect, thus, determines the optimum number of pulses in the burst in applications of laser ablation for material removal.
- 21 April 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (5) , 1-14
Effect of the spot size on ionization and degree of plasma shielding in plumes induced by irradiation of a copper target by multiple short laser pulses
- 21 April 2020
- Published by Springer Nature in Applied Physics A
- Vol. 126 (5) , 1-14
Effect of the spot size on ionization and degree of plasma shielding in plumes induced by irradiation of a copper target by multiple short laser pulses
- 11 December 2017
- Published by Springer Nature in Applied Physics A
- Vol. 124 (1) , 32
Effect of the background gas pressure on the effectiveness of laser-induced material removal from deep cavities in irradiated targets
- 11 December 2017
- Published by Springer Nature in Applied Physics A
- Vol. 124 (1) , 32
Effect of the background gas pressure on the effectiveness of laser-induced material removal from deep cavities in irradiated targets