Yongsun Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yongsun Lee has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jaehyouk Choi
Department of Electrical and Computer Engineering and the Inter-University Semiconductor Research Center, Seoul National University, Seoul, South Korea
10 shared publications - Seyeon Yoo
QUALCOMM Inc., San Diego, CA, USA
8 shared publications - Taeho Seong
QUALCOMM Inc., San Diego, CA, USA
6 shared publications - Younghyun Lim
Kyung Hee University
5 shared publications - Jeonghyun Lee
Device Solutions Samsung Electronics, Hwaseong, Gyeongggi, South Korea
3 shared publications - Seojin Choi
Ulsan National Institute of Science and Technology (UNIST), Ulsan, Korea
3 shared publications
Latest Publications
- Top Cited Papers
- 25 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2841-2855
A Low-Jitter and Low-Fractional-Spur Ring-DCO-Based Fractional-N Digital PLL Using a DTC’s Second-/Third-Order Nonlinearity Cancellation and a Probability-Density-Shaping ΔΣM
This work presents a low-jitter and low-spur, fractional- $N$ ring-oscillator-based digital phase-locked loop (RO-DPLL). First, to suppress fractional spurs, the probability-density-shaping delta–sigma modulator (PDS- $\Delta \Sigma \text{M}$ ) is presented. Since the output codes of the PDS- $\Delta \Sigma \text{M}$ are designed to have a time-invariant probability density function (PDF), they have spur immunity to any nonlinearity (NL) of the digital-to-time converter (DTC). In addition, by using a special dither consisting of uniform random numbers (URNs) based on the dithered quantization theorems, the PDS- $\Delta \Sigma \text{M}$ can also suppress fractional spurs due to the NL of other loop-building circuits. Second, the DTC’s second-/third-order nonlinearity cancellation (DST-NLC) technique is presented to reduce the quantization noise (Q-noise), thereby reducing the rms jitter. The proposed RO-DPLL was fabricated in 65-nm CMOS, and it used a 0.146-mm 2 silicon area and 9.27-mW power. At a near-integer- $N$ frequency, i.e., near 5.3 GHz, the measured rms jitter and the fractional spur were less than 365 fs and −63 dBc, respectively.
- 25 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (9) , 2841-2855
Top Cited PapersA Low-Jitter and Low-Fractional-Spur Ring-DCO-Based Fractional-N Digital PLL Using a DTC’s Second-/Third-Order Nonlinearity Cancellation and a Probability-Density-Shaping ΔΣM
This work presents a low-jitter and low-spur, fractional- $N$ ring-oscillator-based digital phase-locked loop (RO-DPLL). First, to suppress fractional spurs, the probability-density-shaping delta–sigma modulator (PDS- $\Delta \Sigma \text{M}$ ) is presented. Since the output codes of the PDS- $\Delta \Sigma \text{M}$ are designed to have a time-invariant probability density function (PDF), they have spur immunity to any nonlinearity (NL) of the digital-to-time converter (DTC). In addition, by using a special dither consisting of uniform random numbers (URNs) based on the dithered quantization theorems, the PDS- $\Delta \Sigma \text{M}$ can also suppress fractional spurs due to the NL of other loop-building circuits. Second, the DTC’s second-/third-order nonlinearity cancellation (DST-NLC) technique is presented to reduce the quantization noise (Q-noise), thereby reducing the rms jitter. The proposed RO-DPLL was fabricated in 65-nm CMOS, and it used a 0.146-mm 2 silicon area and 9.27-mW power. At a near-integer- $N$ frequency, i.e., near 5.3 GHz, the measured rms jitter and the fractional spur were less than 365 fs and −63 dBc, respectively.
- 28 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (1) , 298-309
A Low-Jitter and Low-Reference-Spur Ring-VCO- Based Injection-Locked Clock Multiplier Using a Triple-Point Background Calibrator
This work presents a low-jitter, low-reference-spur ring voltage-controlled oscillator (ring VCO)-based injection-locked clock multiplier (ILCM). Since the proposed triple-point frequency/phase/slope calibrator (TP-FPSC) can accurately remove the three root causes of the frequency errors of ILCMs (i.e., frequency drift, phase offset, and slope modulation), the ILCM of this work is able to achieve a low-level-reference spur. In addition, the calibrating loop for the frequency drift of the TP-FPSC offers an additional suppression to the in-band phase noise of the output signal. This capability of the TP-FPSC and the naturally wide bandwidth of the injection-locking mechanism allows the ILCM to achieve a very low-RMS jitter. The ILCM was fabricated in a 65-nm CMOS technology. The measured reference spur and RMS jitter of the 2.4-GHz output signal were -72 dBc and 140 fs, respectively, both of which are the best among the state-of-the-art ILCMs. The active silicon area was 0.055 mm², and the power consumption was 11.0 mW.
- 28 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (1) , 298-309
A Low-Jitter and Low-Reference-Spur Ring-VCO- Based Injection-Locked Clock Multiplier Using a Triple-Point Background Calibrator
This work presents a low-jitter, low-reference-spur ring voltage-controlled oscillator (ring VCO)-based injection-locked clock multiplier (ILCM). Since the proposed triple-point frequency/phase/slope calibrator (TP-FPSC) can accurately remove the three root causes of the frequency errors of ILCMs (i.e., frequency drift, phase offset, and slope modulation), the ILCM of this work is able to achieve a low-level-reference spur. In addition, the calibrating loop for the frequency drift of the TP-FPSC offers an additional suppression to the in-band phase noise of the output signal. This capability of the TP-FPSC and the naturally wide bandwidth of the injection-locking mechanism allows the ILCM to achieve a very low-RMS jitter. The ILCM was fabricated in a 65-nm CMOS technology. The measured reference spur and RMS jitter of the 2.4-GHz output signal were -72 dBc and 140 fs, respectively, both of which are the best among the state-of-the-art ILCMs. The active silicon area was 0.055 mm², and the power consumption was 11.0 mW.
- 11 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (12) , 3466-3477
An Ultra-Low-Jitter, mmW-Band Frequency Synthesizer Based on Digital Subsampling PLL Using Optimally Spaced Voltage Comparators
This article presents a cascaded architecture of a frequency synthesizer to generate ultra-low-jitter output signals in a millimeter-wave (mmW) frequency band from 28 to 31 GHz. The mmW-band injection-locked frequency multiplier (ILFM) placed at the second stage has a wide bandwidth so that the performance of the jitter of this frequency synthesizer is determined by the GHz-band, digital subsampling phase-locked loop (SSPLL) at the first stage. To suppress the quantization noise of the digital SSPLL while using a small amount of power, the optimally spaced voltage comparators (OSVCs) are presented as a voltage quantizer. This article was designed and fabricated using 65-nm CMOS technology. In measurements, this prototype frequency synthesizer generated output signals in the range of 28-31 GHz, with an rms jitter of less than 80 fs and an integrated phase noise (IPN) of less than -40 dBc. The active silicon area was 0.32 mm 2 , and the total power consumption was 41.8 mW.
- 11 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (12) , 3466-3477
An Ultra-Low-Jitter, mmW-Band Frequency Synthesizer Based on Digital Subsampling PLL Using Optimally Spaced Voltage Comparators
This article presents a cascaded architecture of a frequency synthesizer to generate ultra-low-jitter output signals in a millimeter-wave (mmW) frequency band from 28 to 31 GHz. The mmW-band injection-locked frequency multiplier (ILFM) placed at the second stage has a wide bandwidth so that the performance of the jitter of this frequency synthesizer is determined by the GHz-band, digital subsampling phase-locked loop (SSPLL) at the first stage. To suppress the quantization noise of the digital SSPLL while using a small amount of power, the optimally spaced voltage comparators (OSVCs) are presented as a voltage quantizer. This article was designed and fabricated using 65-nm CMOS technology. In measurements, this prototype frequency synthesizer generated output signals in the range of 28-31 GHz, with an rms jitter of less than 80 fs and an integrated phase noise (IPN) of less than -40 dBc. The active silicon area was 0.32 mm 2 , and the total power consumption was 41.8 mW.
- 17 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (9) , 2501-2512
A 320-fs RMS Jitter and – 75-dBc Reference-Spur Ring-DCO-Based Digital PLL Using an Optimal-Threshold TDC
- 17 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (9) , 2501-2512
A 320-fs RMS Jitter and – 75-dBc Reference-Spur Ring-DCO-Based Digital PLL Using an Optimal-Threshold TDC
- 19 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (4) , 927-936
An Ultra-Low-Jitter 22.8-GHz Ring-LC-Hybrid Injection-Locked Clock Multiplier With a Multiplication Factor of 114
- 19 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (4) , 927-936
An Ultra-Low-Jitter 22.8-GHz Ring-LC-Hybrid Injection-Locked Clock Multiplier With a Multiplication Factor of 114
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 210-213
A 320µV-Output Ripple and 90ns-Settling Time at 0.5V Supply Digital-Analog-Hybrid LDO Using Multi-Level Gate-Voltage Generator and Fast-Decision PD Detector
This work presents a digital-analog-hybrid LDO (HLDO) using a multi-level gate-voltage generator (MGG) to achieve a small output ripple (VR) and a fast-transient response. Using the MGG that can partially turn on transistors in the power MOSFET (Mp) and thus reduce Mp's LSB current, VR was limited to less than 320 μV. Also, a fast-decision PD detector having a non-zero decision level expedited the switching of transistors in Mp, thereby reducing the settling time to less than 90 ns.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 210-213
A 320µV-Output Ripple and 90ns-Settling Time at 0.5V Supply Digital-Analog-Hybrid LDO Using Multi-Level Gate-Voltage Generator and Fast-Decision PD Detector
This work presents a digital-analog-hybrid LDO (HLDO) using a multi-level gate-voltage generator (MGG) to achieve a small output ripple (VR) and a fast-transient response. Using the MGG that can partially turn on transistors in the power MOSFET (Mp) and thus reduce Mp's LSB current, VR was limited to less than 320 μV. Also, a fast-decision PD detector having a non-zero decision level expedited the switching of transistors in Mp, thereby reducing the settling time to less than 90 ns.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 185-186
153 FSRMS-Integrated-Jitter and 114-Multiplication Factor PVT-Robust 22.8 GHZ Ring-LC-Hybrid Injection-Locked Clock Multiplier
This work presents an ultra-low-jitter hybrid injection-locked clock multiplier (ILCM) that cascades a ring ILCM and an LC ILCM to achieve a high multiplication factor of 114. A dual-pur-pose frequency calibrator (DPFC) that can calibrate the frequency drifts of the two VCOs, concurrently, consumes only 400μ W. The RMS-jitter of the output signal at 22.8 GHz was 153 fs. Due to the DPFC, RMS-jitter was maintained to be less than 180 fs, across supply voltages and temperatures.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 185-186
153 FSRMS-Integrated-Jitter and 114-Multiplication Factor PVT-Robust 22.8 GHZ Ring-LC-Hybrid Injection-Locked Clock Multiplier
This work presents an ultra-low-jitter hybrid injection-locked clock multiplier (ILCM) that cascades a ring ILCM and an LC ILCM to achieve a high multiplication factor of 114. A dual-pur-pose frequency calibrator (DPFC) that can calibrate the frequency drifts of the two VCOs, concurrently, consumes only 400μ W. The RMS-jitter of the output signal at 22.8 GHz was 153 fs. Due to the DPFC, RMS-jitter was maintained to be less than 180 fs, across supply voltages and temperatures.
- 16 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (4) , 1192-1202
A Low-Jitter and Low-Reference-Spur Ring-VCO-Based Switched-Loop Filter PLL Using a Fast Phase-Error Correction Technique
A low-jitter and low-reference-spur ring-type voltage-controlled oscillator (VCO)-based switched-loop filter (SLF) phase-locked loop (PLL) is presented. To enhance the capability of suppressing jitter of a VCO, we propose a fast phase-error correction (FPEC) technique that emulates the phase-realignment mechanism of an injection-locked clock multiplier. By the proposed FPEC technique, accumulated jitter of a VCO can be removed intensively in a short interval, thereby suppressing jitter dramatically. Based on a PLL topology having an intrinsic integrator in a VCO, the proposed architecture can also achieve a low reference spur despite a high multiplication factor (i.e., 64). This paper also presents the selective frequency-tuning technique used in the VCO that helps the proposed architecture further suppress the level of reference spur. The proposed PLL was fabricated in a 65-nm CMOS process. The measured rms jitter integrated from 1 kHz to 80 MHz and the reference spur of the output signal with a 3.008-GHz frequency were 357 fs and -71 dBc, respectively. The total active area was 0.047 mm², and the power consumption was 4.6 mW.
- 16 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (4) , 1192-1202
A Low-Jitter and Low-Reference-Spur Ring-VCO-Based Switched-Loop Filter PLL Using a Fast Phase-Error Correction Technique
A low-jitter and low-reference-spur ring-type voltage-controlled oscillator (VCO)-based switched-loop filter (SLF) phase-locked loop (PLL) is presented. To enhance the capability of suppressing jitter of a VCO, we propose a fast phase-error correction (FPEC) technique that emulates the phase-realignment mechanism of an injection-locked clock multiplier. By the proposed FPEC technique, accumulated jitter of a VCO can be removed intensively in a short interval, thereby suppressing jitter dramatically. Based on a PLL topology having an intrinsic integrator in a VCO, the proposed architecture can also achieve a low reference spur despite a high multiplication factor (i.e., 64). This paper also presents the selective frequency-tuning technique used in the VCO that helps the proposed architecture further suppress the level of reference spur. The proposed PLL was fabricated in a 65-nm CMOS process. The measured rms jitter integrated from 1 kHz to 80 MHz and the reference spur of the output signal with a 3.008-GHz frequency were 357 fs and -71 dBc, respectively. The total active area was 0.047 mm², and the power consumption was 4.6 mW.
- 22 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (2) , 375-388
A Low-Integrated-Phase-Noise 27–30-GHz Injection-Locked Frequency Multiplier With an Ultra-Low-Power Frequency-Tracking Loop for mm-Wave-Band 5G Transceivers
An ultra-low-phase-noise injection-locked frequency multiplier (ILFM) for millimeter wave (mm-wave) fifth-generation transceivers is presented. Using an ultra-low-power frequency-tracking loop (FTL), the proposed ILFM is able to correct the frequency drifts of the quadrature voltage-controlled oscillator of the ILFM in a real-time fashion. Since the FTL is monitoring the averages of phase deviations rather than detecting or sampling the instantaneous values, it requires only 600 μW to continue to calibrate the ILFM that generates an mm-wave signal with an output frequency from 27 to 30 GHz. The proposed ILFM was fabricated in a 65-nm CMOS process. The 10-MHz phase noise of the 29.25-GHz output signal was -129.7 dBc/Hz, and its variations across temperatures and supply voltages were less than 2 dB. The integrated phase noise from 1 kHz to 100 MHz and the rms jitter were -39.1 dBc and 86 fs, respectively.
- 22 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (2) , 375-388
A Low-Integrated-Phase-Noise 27–30-GHz Injection-Locked Frequency Multiplier With an Ultra-Low-Power Frequency-Tracking Loop for mm-Wave-Band 5G Transceivers
An ultra-low-phase-noise injection-locked frequency multiplier (ILFM) for millimeter wave (mm-wave) fifth-generation transceivers is presented. Using an ultra-low-power frequency-tracking loop (FTL), the proposed ILFM is able to correct the frequency drifts of the quadrature voltage-controlled oscillator of the ILFM in a real-time fashion. Since the FTL is monitoring the averages of phase deviations rather than detecting or sampling the instantaneous values, it requires only 600 μW to continue to calibrate the ILFM that generates an mm-wave signal with an output frequency from 27 to 30 GHz. The proposed ILFM was fabricated in a 65-nm CMOS process. The 10-MHz phase noise of the 29.25-GHz output signal was -129.7 dBc/Hz, and its variations across temperatures and supply voltages were less than 2 dB. The integrated phase noise from 1 kHz to 100 MHz and the rms jitter were -39.1 dBc and 86 fs, respectively.