Dongwook Shin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dongwook Shin has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Jinyi Choi
Hanyang Univ, Dept Fuel Cells & Hydrogen Technol, 222 Wangsimni Ro, Seoul 04763, South Korea
4 shared publicationsKihyun Cho
4 shared publicationsInyu Park
Department of Fuel cells and Hydrogen Technology, Hanyang University, Republic of Korea
3 shared publicationsChanhwi Park
Division of Materials Science & Engineering, Hanyang University, Seongdong-gu, Seoul 04763, Korea
2 shared publicationsHunhyeong Lee
Division of Materials Science & Engineering, Hanyang University, Republic of Korea
2 shared publicationsJangwon Oh
Division of Material Science & Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791, Republic of Korea
2 shared publications
Latest Publications
- Open Access
Porous Poly(4-vinylpyridine) Coatings Prepared by Electrostatic Slurry Spray Deposition: Morphological Control and Preliminary Formaldehyde-Reduction Assessment
Porous poly(4-vinylpyridine) (P4VP) coatings were fabricated by electrostatic slurry spray deposition (ESSD) using solution and ethanol–water composite-slurry precursors. Thirty-four solvents were screened to examine the relationship between precursor formulation, spray behavior, and deposited morphology. Gradual nonsolvent addition generated a particulate composite slurry, with a principal volume-weighted dynamic light scattering (DLS) peak at 13.78 nm for the 7.4 wt.% formulation. Under the investigated conditions, this slurry produced a more spatially uniform porous coating than the solution precursor and was successfully deposited onto a three-dimensional fibrous filter scaffold. During a preliminary 30 m3 chamber assessment of the air-purifier system equipped with the coated filter, formaldehyde (HCHO) concentration decreased from 0.846 to 0.702 ppm in 1 h, corresponding to an apparent concentration-decay-based air-cleaning rate (Qapp) of approximately 5.69 m3 h−1. This preliminary observation describes the performance of the assembled air-purifier system; the principal contribution of the study is the formulation and morphological control of porous P4VP coatings through composite-slurry ESSD.
Open AccessPorous Poly(4-vinylpyridine) Coatings Prepared by Electrostatic Slurry Spray Deposition: Morphological Control and Preliminary Formaldehyde-Reduction Assessment
Porous poly(4-vinylpyridine) (P4VP) coatings were fabricated by electrostatic slurry spray deposition (ESSD) using solution and ethanol–water composite-slurry precursors. Thirty-four solvents were screened to examine the relationship between precursor formulation, spray behavior, and deposited morphology. Gradual nonsolvent addition generated a particulate composite slurry, with a principal volume-weighted dynamic light scattering (DLS) peak at 13.78 nm for the 7.4 wt.% formulation. Under the investigated conditions, this slurry produced a more spatially uniform porous coating than the solution precursor and was successfully deposited onto a three-dimensional fibrous filter scaffold. During a preliminary 30 m3 chamber assessment of the air-purifier system equipped with the coated filter, formaldehyde (HCHO) concentration decreased from 0.846 to 0.702 ppm in 1 h, corresponding to an apparent concentration-decay-based air-cleaning rate (Qapp) of approximately 5.69 m3 h−1. This preliminary observation describes the performance of the assembled air-purifier system; the principal contribution of the study is the formulation and morphological control of porous P4VP coatings through composite-slurry ESSD.
- Open Access
Electrospray as an Atomized Precursor-Delivery Strategy for Stöber Silica Nanosphere Synthesis
Electrospray provides an atomized precursor delivery strategy for controlling silica particle formation during Stöber synthesis. In this study, electrospray and drop-by-drop precursor delivery were compared across 0.1–0.5 mL/min to evaluate delivery-mode effects on particle size and size distribution. The mean particle size increased with flow rate under electrospray delivery, whereas the opposite trend was observed under drop-by-drop delivery. Electrospray maintained relatively narrow particle size distributions, with coefficients of variation ranging from 5.6 to 6.7%. These contrasting behaviors were interpreted in terms of differences in local precursor supply conditions and their possible influence on the relative contributions of particle growth and secondary nucleation. Under stable cone-jet electrospray conditions, the mean particle size increased progressively with reaction time at both 7.8 and 9.3 kV, while the coefficient of variation remained approximately 7% throughout. In addition, particles synthesized at 9.3 kV exhibited smaller mean diameters than those obtained at 7.8 kV at all investigated reaction times, while maintaining relatively narrow particle size distributions under both stable cone-jet conditions. Overall, these findings suggest that electrospray offers an additional process-based approach for adjusting silica particle size through control of precursor supply rate and atomization characteristics.
Open AccessElectrospray as an Atomized Precursor-Delivery Strategy for Stöber Silica Nanosphere Synthesis
Electrospray provides an atomized precursor delivery strategy for controlling silica particle formation during Stöber synthesis. In this study, electrospray and drop-by-drop precursor delivery were compared across 0.1–0.5 mL/min to evaluate delivery-mode effects on particle size and size distribution. The mean particle size increased with flow rate under electrospray delivery, whereas the opposite trend was observed under drop-by-drop delivery. Electrospray maintained relatively narrow particle size distributions, with coefficients of variation ranging from 5.6 to 6.7%. These contrasting behaviors were interpreted in terms of differences in local precursor supply conditions and their possible influence on the relative contributions of particle growth and secondary nucleation. Under stable cone-jet electrospray conditions, the mean particle size increased progressively with reaction time at both 7.8 and 9.3 kV, while the coefficient of variation remained approximately 7% throughout. In addition, particles synthesized at 9.3 kV exhibited smaller mean diameters than those obtained at 7.8 kV at all investigated reaction times, while maintaining relatively narrow particle size distributions under both stable cone-jet conditions. Overall, these findings suggest that electrospray offers an additional process-based approach for adjusting silica particle size through control of precursor supply rate and atomization characteristics.
- Open Access
Chemically Active LiH2PO4 Interphase Precursor Enables Self-Limited Interface Stabilization in Sulfide-Based All-Solid-State Batteries
The commercialization of sulfide-based all-solid-state batteries (ASSBs) is severely limited by the interfacial degradation between layered oxide cathodes and sulfide solid electrolytes, resulting in electrolyte decomposition, impedance growth, and rapid capacity fading. Herein, we propose lithium dihydrogen phosphate (LiH2PO4, LDP) as a low-cost polyanionic interphase precursor to regulate the cathode–electrolyte interface. A uniform LDP coating was deposited onto polycrystalline NCM622 particles, producing a continuous 40-nm-thick phosphate layer. Although the LDP-coated electrode exhibited a higher initial interfacial resistance than the bare cathode, electrochemical analyses revealed a capacity retention of 94.1% after 100 cycles, compared with 73.9% for the uncoated electrode. X-ray photoelectron spectroscopy demonstrated that LiH2PO4 is not chemically inert toward Li6PS5Cl but undergoes a controlled initial reaction with sulfur-deficient species to generate a phosphate-rich artificial interphase while suppressing the unstable P–[S]n–P species. This interphase rapidly reaches chemical equilibrium, suppressing sulfur precipitation, SOx formation, and subsequent electrolyte decomposition. Cross-sectional STEM–EDS and focused ion beam analyses revealed that the artificial phosphate interphase inhibited elemental interdiffusion, suppressed chemical mixing, and preserved mechanical contact during prolonged cycling. These findings demonstrate that the electrochemical penalty associated with the initial formation of the LDP interphase represents the necessary cost of constructing a chemically stable interface rather than a degradation process. This study introduces a new interfacial design strategy based on chemically active sacrificial interphase precursors, providing an alternative to conventional inert oxide coatings for realizing long-term stable sulfide-based all-solid-state batteries.
Open AccessChemically Active LiH2PO4 Interphase Precursor Enables Self-Limited Interface Stabilization in Sulfide-Based All-Solid-State Batteries
The commercialization of sulfide-based all-solid-state batteries (ASSBs) is severely limited by the interfacial degradation between layered oxide cathodes and sulfide solid electrolytes, resulting in electrolyte decomposition, impedance growth, and rapid capacity fading. Herein, we propose lithium dihydrogen phosphate (LiH2PO4, LDP) as a low-cost polyanionic interphase precursor to regulate the cathode–electrolyte interface. A uniform LDP coating was deposited onto polycrystalline NCM622 particles, producing a continuous 40-nm-thick phosphate layer. Although the LDP-coated electrode exhibited a higher initial interfacial resistance than the bare cathode, electrochemical analyses revealed a capacity retention of 94.1% after 100 cycles, compared with 73.9% for the uncoated electrode. X-ray photoelectron spectroscopy demonstrated that LiH2PO4 is not chemically inert toward Li6PS5Cl but undergoes a controlled initial reaction with sulfur-deficient species to generate a phosphate-rich artificial interphase while suppressing the unstable P–[S]n–P species. This interphase rapidly reaches chemical equilibrium, suppressing sulfur precipitation, SOx formation, and subsequent electrolyte decomposition. Cross-sectional STEM–EDS and focused ion beam analyses revealed that the artificial phosphate interphase inhibited elemental interdiffusion, suppressed chemical mixing, and preserved mechanical contact during prolonged cycling. These findings demonstrate that the electrochemical penalty associated with the initial formation of the LDP interphase represents the necessary cost of constructing a chemically stable interface rather than a degradation process. This study introduces a new interfacial design strategy based on chemically active sacrificial interphase precursors, providing an alternative to conventional inert oxide coatings for realizing long-term stable sulfide-based all-solid-state batteries.
- 27 August 2020
- Published by Springer Nature in Journal of Electroceramics
- Vol. 45 (1) , 1-6
Cell performance enhancement facilitated by mixed ionic and electronic conductor fiber for protonic ceramic fuel cells
- 27 August 2020
- Published by Springer Nature in Journal of Electroceramics
- Vol. 45 (1) , 1-6
Cell performance enhancement facilitated by mixed ionic and electronic conductor fiber for protonic ceramic fuel cells
- Open Access
- 9 January 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5318-A5322
Electrochemical Properties of Composite Cathode Using Bimodal Sized Electrolyte for All-Solid-State Batteries
To enhance the packing density of composite cathode for all-solid-state lithium-ion batteries, the effect of a bimodal sized solid electrolyte was studied. The composite cathode, which is fabricated using the powder compression method, consisted of the cathode active material, a conductive agent, and the solid electrolyte. However, the composite cathode construction had voids. The voids in the composite cathode were restricted to ionic conduction between the cathode active materials and the solid electrolytes. Suppression of the voids in the composite cathode improved the electrochemical performance of the all-solid-state battery. A composite cathode using bimodal sized electrolyte powders demonstrated better cell performance than that using only fine or coarse sized electrolyte powders. These results demonstrated that the composite cathode using the bimodal sized electrolyte enhanced the electrochemical performance of the all-solid-state battery because it improved the packing density of the cathode.
- 9 January 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5318-A5322
Open AccessElectrochemical Properties of Composite Cathode Using Bimodal Sized Electrolyte for All-Solid-State Batteries
To enhance the packing density of composite cathode for all-solid-state lithium-ion batteries, the effect of a bimodal sized solid electrolyte was studied. The composite cathode, which is fabricated using the powder compression method, consisted of the cathode active material, a conductive agent, and the solid electrolyte. However, the composite cathode construction had voids. The voids in the composite cathode were restricted to ionic conduction between the cathode active materials and the solid electrolytes. Suppression of the voids in the composite cathode improved the electrochemical performance of the all-solid-state battery. A composite cathode using bimodal sized electrolyte powders demonstrated better cell performance than that using only fine or coarse sized electrolyte powders. These results demonstrated that the composite cathode using the bimodal sized electrolyte enhanced the electrochemical performance of the all-solid-state battery because it improved the packing density of the cathode.
- Open Access
- 19 December 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5193-A5200
Application of Rod-Like Li6PS5Cl Directly Synthesized by a Liquid Phase Process to Sheet-Type Electrodes for All-Solid-State Lithium Batteries
All-solid-state lithium batteries employing sulfide-based solid electrolytes have emerged as promising next-generation batteries for large-scale energy storage applications because of their safety and high energy density. Among them, Li6PS5X (X = Cl, Br, I) with an argyrodite structure synthesized by planetary milling exhibits a rather high lithium ion conductivity of 10−2 – 10−3 S cm−1 at room temperature. Unfortunately, the planetary milling process has the disadvantage of producing the solid electrolytes with large, round-shaped particles. Recently, the solid electrolytes have been synthesized by not the mechanical milling but the liquid-phase process, which facilitates synthesis of sub-micrometer- to nanometer-sized solid electrolyte particles. It is important to reduce the particle size of the solid electrolyte to promote intimate contact with the active material in the composite cathode. Here, rod-like Li6PS5Cl solid electrolyte with a high ionic conductivity of 1.1 × 10−3 S cm−1 at room temperature was, for the first time, directly prepared by a liquid phase process using only a stirring method. SEM images showed the electrolyte had a rod-like morphology with a length of 20–30 μm and a width of 2–3 μm. The composite cathode was prepared from a slurry and the cell performances were investigated.
- 19 December 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5193-A5200
Open AccessApplication of Rod-Like Li6PS5Cl Directly Synthesized by a Liquid Phase Process to Sheet-Type Electrodes for All-Solid-State Lithium Batteries
All-solid-state lithium batteries employing sulfide-based solid electrolytes have emerged as promising next-generation batteries for large-scale energy storage applications because of their safety and high energy density. Among them, Li6PS5X (X = Cl, Br, I) with an argyrodite structure synthesized by planetary milling exhibits a rather high lithium ion conductivity of 10−2 – 10−3 S cm−1 at room temperature. Unfortunately, the planetary milling process has the disadvantage of producing the solid electrolytes with large, round-shaped particles. Recently, the solid electrolytes have been synthesized by not the mechanical milling but the liquid-phase process, which facilitates synthesis of sub-micrometer- to nanometer-sized solid electrolyte particles. It is important to reduce the particle size of the solid electrolyte to promote intimate contact with the active material in the composite cathode. Here, rod-like Li6PS5Cl solid electrolyte with a high ionic conductivity of 1.1 × 10−3 S cm−1 at room temperature was, for the first time, directly prepared by a liquid phase process using only a stirring method. SEM images showed the electrolyte had a rod-like morphology with a length of 20–30 μm and a width of 2–3 μm. The composite cathode was prepared from a slurry and the cell performances were investigated.
- 1 June 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (24) , 11372-11377
Microstructural stability of SSC fibrous cathode with embedded SDC particles for solid oxide fuel cells operating on hydrogen
- 1 June 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (24) , 11372-11377
Microstructural stability of SSC fibrous cathode with embedded SDC particles for solid oxide fuel cells operating on hydrogen
- 8 March 2018
- Published by Springer Nature in Journal of Electroceramics
- Vol. 40 (4) , 293-299
Importance of mixing protocol for enhanced performance of composite cathodes in all-solid-state batteries using sulfide solid electrolyte
- 8 March 2018
- Published by Springer Nature in Journal of Electroceramics
- Vol. 40 (4) , 293-299
Importance of mixing protocol for enhanced performance of composite cathodes in all-solid-state batteries using sulfide solid electrolyte
- 30 March 2015
- Published by The Mineralogical Society of Korea in Journal of the Mineralogical Society of Korea
- Vol. 28 (1) , 51-60
Gemological Characteristics of Aquamarine from the Gilgit-Baltistan of Northern Areas, Pakistan
- 30 March 2015
- Published by The Mineralogical Society of Korea in Journal of the Mineralogical Society of Korea
- Vol. 28 (1) , 51-60
Gemological Characteristics of Aquamarine from the Gilgit-Baltistan of Northern Areas, Pakistan
- 1 January 2015
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 15 (1) , 536-539
Preparation of NiO-YSZ Composite Powder Through 2-Step Hydrothermal Synthesis and Its Application to Solid Oxide Fuel Cell Anode Functional Layer
NiO-YSZ composite powders were prepared by 2-step hydrothermal synthesis and applied as an anode functional layer to improve the performance of SOFCs. The precursor solution containing yttrium chloride, zirconium oxychloride, and nickel nitrate was hydrothermally treated at 100∼130°C for 36 h and then calcined at 900°C for 4 h. The results of X-ray diffraction, Field-Emission Scanning Electron Microscope and Transmission Electron Microscope showed that the NiO (50∼100 nm) and YSZ (200∼300 nm) were successfully synthesized and these two phases were well separated with the weak agglomeration. Electrical conductivity of the cermet made from the powders produced by 2-step hydrothermal synthesiswasmuch higher than that of the cermet prepared by ball milling. A single cell with anode functional layer showed a maximum power density of 1.7 W/cm2 at 800°C, which may be owing to the homogeneous distribution and the small particle size of the obtained powders.
- 1 January 2015
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 15 (1) , 536-539
Preparation of NiO-YSZ Composite Powder Through 2-Step Hydrothermal Synthesis and Its Application to Solid Oxide Fuel Cell Anode Functional Layer
NiO-YSZ composite powders were prepared by 2-step hydrothermal synthesis and applied as an anode functional layer to improve the performance of SOFCs. The precursor solution containing yttrium chloride, zirconium oxychloride, and nickel nitrate was hydrothermally treated at 100∼130°C for 36 h and then calcined at 900°C for 4 h. The results of X-ray diffraction, Field-Emission Scanning Electron Microscope and Transmission Electron Microscope showed that the NiO (50∼100 nm) and YSZ (200∼300 nm) were successfully synthesized and these two phases were well separated with the weak agglomeration. Electrical conductivity of the cermet made from the powders produced by 2-step hydrothermal synthesiswasmuch higher than that of the cermet prepared by ball milling. A single cell with anode functional layer showed a maximum power density of 1.7 W/cm2 at 800°C, which may be owing to the homogeneous distribution and the small particle size of the obtained powders.