Nicolas Godard
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nicolas Godard has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Emmanuel Defay
Luxembourg Institute of Science and Technology
6 shared publications - Sebastjan Glinsek
Smart Materials Unit Luxembourg Institute of Science and Technology 41 rue du Brill L‐4422 Belvaux Luxembourg
6 shared publications - Cosme Milesi-Brault
Laboratoire Structures, Propriétés et Modélisation des Solides (SPMS), Université Paris-Saclay, CentraleSupélec, CNRS, Gif-sur-Yvette, France
2 shared publications - Mohamed Aymen Mahjoub
Materials Research and Technology Department, Luxembourg Institute of Science and Technology, L-4422 Belvaux, Luxembourg
2 shared publications Stéphanie Girod
Materials Research and Technology Department, Luxembourg Institute of Science and Technology 1 , 41 rue du Brill, L-4422 Belvaux, Luxembourg
2 shared publications- Tony Schenk
Materials Research and Technology Department Luxembourg Institute of Science and Technology (LIST) 41 Rue du Brill L-4422 Belvaux Luxembourg
2 shared publications
Latest Publications
- Open Access
- 1 October 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (13) , 6449-6455
Solution-processed BiFeO3 thin films with low leakage current
- 1 October 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (13) , 6449-6455
Open AccessSolution-processed BiFeO3 thin films with low leakage current
- 25 January 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (4) , 042901
Critical field anisotropy in the antiferroelectric switching of PbZrO3 films
Antiferroelectrics have been recently sparking interest due to their potential use in energy storage and electrocaloric cooling. Their main distinctive feature is antiferroelectric switching, i.e., the possibility to induce a phase transition to a polar phase by an electric field. Here, we investigate the switching behavior of the model antiferroelectric perovskite PbZrO3 using thin films processed by chemical solution deposition in different geometries and orientations. Both out-of-plane and in-plane switching configurations are investigated. The critical field is observed to be highly dependent on the direction of the electric field with respect to the film texture. We show that this behavior is qualitatively consistent with a phase transition to a rhombohedral polar phase. We finally estimate the importance of crystallite orientation and film texturation in the variations observed in the literature.
- 25 January 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (4) , 042901
Critical field anisotropy in the antiferroelectric switching of PbZrO3 films
Antiferroelectrics have been recently sparking interest due to their potential use in energy storage and electrocaloric cooling. Their main distinctive feature is antiferroelectric switching, i.e., the possibility to induce a phase transition to a polar phase by an electric field. Here, we investigate the switching behavior of the model antiferroelectric perovskite PbZrO3 using thin films processed by chemical solution deposition in different geometries and orientations. Both out-of-plane and in-plane switching configurations are investigated. The critical field is observed to be highly dependent on the direction of the electric field with respect to the film texture. We show that this behavior is qualitatively consistent with a phase transition to a rhombohedral polar phase. We finally estimate the importance of crystallite orientation and film texturation in the variations observed in the literature.
- Open Access
- 8 December 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (1) , 281-287
Growth of {100}-oriented lead zirconate titanate thin films mediated by a safe solvent
Chemical solution deposition (CSD) is a well-established process for the fabrication of metal oxide functional layers such as piezoelectric lead zirconate titanate (PZT) thin films. The latter exhibit an enhanced electromechanical response in the presence of {100} crystalline orientation with respect to the substrate surface. Lead titanate (PbTiO3) seed layers are commonly used to promote the growth of this orientation on platinized silicon, which otherwise usually affords the {111} orientation. In this work, we present a comparative study of two solvents used for the preparation of PZT and PbTiO3 solutions for CSD, i.e. the popular but highly carcinogenic and teratogenic solvent 2-methoxyethanol and the benign solvent 1-methoxy-2-propanol. In addition to tremendous health and safety benefits, we show that 1-methoxy-2-propanol-derived PbTiO3 seed layers promote the {100} orientation more efficiently than their 2-methoxyethanol-derived counterparts, owing to their nanocrystalline microstructure and strong orientation. This resulted in a noticeable enhancement of the electrical and piezoelectric properties, with Pr = 38 μC cm−2, Ec = 55 kV cm−1, εr = 1300, tan δ = 0.04 and e31,f ≈ 14 C m−2.
- 8 December 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (1) , 281-287
Open AccessGrowth of {100}-oriented lead zirconate titanate thin films mediated by a safe solvent
Chemical solution deposition (CSD) is a well-established process for the fabrication of metal oxide functional layers such as piezoelectric lead zirconate titanate (PZT) thin films. The latter exhibit an enhanced electromechanical response in the presence of {100} crystalline orientation with respect to the substrate surface. Lead titanate (PbTiO3) seed layers are commonly used to promote the growth of this orientation on platinized silicon, which otherwise usually affords the {111} orientation. In this work, we present a comparative study of two solvents used for the preparation of PZT and PbTiO3 solutions for CSD, i.e. the popular but highly carcinogenic and teratogenic solvent 2-methoxyethanol and the benign solvent 1-methoxy-2-propanol. In addition to tremendous health and safety benefits, we show that 1-methoxy-2-propanol-derived PbTiO3 seed layers promote the {100} orientation more efficiently than their 2-methoxyethanol-derived counterparts, owing to their nanocrystalline microstructure and strong orientation. This resulted in a noticeable enhancement of the electrical and piezoelectric properties, with Pr = 38 μC cm−2, Ec = 55 kV cm−1, εr = 1300, tan δ = 0.04 and e31,f ≈ 14 C m−2.
- Open Access
- 1 June 2020
- Published by Elsevier in Cell Reports Physical Science
- Vol. 1 (6) , 100068
1-mW Vibration Energy Harvester Based on a Cantilever with Printed Polymer Multilayers
- 1 June 2020
- Published by Elsevier in Cell Reports Physical Science
- Vol. 1 (6) , 100068
Open Access1-mW Vibration Energy Harvester Based on a Cantilever with Printed Polymer Multilayers
- Open Access
- 14 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (11) , 3740-3747
On the importance of pyrolysis for inkjet-printed oxide piezoelectric thin films
Inkjet printing (IJP) is an attractive technology for the low-cost fabrication of functional metal oxide thin films, such as piezoelectric lead zirconate titanate (PZT). Implementation of the well-established chemical solution deposition method for PZT films in the IJP process comes with challenges, which were the focus of several works in the field. However, adequate pyrolysis conditions are also required for the complete elimination of organic residues from the layers before crystallization. Thanks to an original technique based on infra-red spectroscopy, the present study draws the correlation between the amount of residual organics in pyrolyzed inkjet-printed layers on platinized silicon and the porosity and functional properties of the final films. Pyrolysis at 475 °C for 3 min afforded dense {111}-textured 200 nm-thick PZT layers after crystallization at 700 °C, with state-of-the-art electrical properties (Pr = 23 μC cm−2, Ec = 60 kV cm−1, ε′ = 1000 and tan δ = 0.04). Potential of inkjet printing technology for piezoelectric devices is demonstrated through a simple energy harvesting device, with a 5.8 μW power output for a 6 kΩ resistive load.
- 14 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (11) , 3740-3747
Open AccessOn the importance of pyrolysis for inkjet-printed oxide piezoelectric thin films
Inkjet printing (IJP) is an attractive technology for the low-cost fabrication of functional metal oxide thin films, such as piezoelectric lead zirconate titanate (PZT). Implementation of the well-established chemical solution deposition method for PZT films in the IJP process comes with challenges, which were the focus of several works in the field. However, adequate pyrolysis conditions are also required for the complete elimination of organic residues from the layers before crystallization. Thanks to an original technique based on infra-red spectroscopy, the present study draws the correlation between the amount of residual organics in pyrolyzed inkjet-printed layers on platinized silicon and the porosity and functional properties of the final films. Pyrolysis at 475 °C for 3 min afforded dense {111}-textured 200 nm-thick PZT layers after crystallization at 700 °C, with state-of-the-art electrical properties (Pr = 23 μC cm−2, Ec = 60 kV cm−1, ε′ = 1000 and tan δ = 0.04). Potential of inkjet printing technology for piezoelectric devices is demonstrated through a simple energy harvesting device, with a 5.8 μW power output for a 6 kΩ resistive load.
- Open Access
- 29 November 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (3) , 1900626
Toward Thick Piezoelectric HfO2‐Based Films
For HfO2‐based films, which are mainly prepared by atomic layer deposition, the desired ferroelectric (FE) properties typically vanish while extending the thickness beyond a limit of about 50 nm. Herein, the successful fabrication of a 1 μm‐thick piezoelectric La:HfO2 film is demonstrated using chemical solution deposition, paving the way toward sensor and actuator applications. After identifying the optimal La content, the film thickness is increased from 45 nm to 1 μm. Polarization and strain measurements evidence the persistence of the FE properties at all thicknesses and even a slight improvement due to a better orientation of the polar axis at higher thicknesses. Scanning electron microscopy and X‐ray reflectivity reveal a fine‐grained microstructure and a density of only 80% of the theoretical value, which seems to be a common issue of solution‐deposited HfO2‐based films, based on the performed literature survey. Using tilt‐angle‐dependent X‐ray diffraction scans, homogeneous nucleation is found to be the likely root cause of the observed microstructure. It is suggested that this microstructure issue is key for the optimization of cycling stability of solution‐based films to exploit the full potential of the HfO2 for cost‐efficient, thick piezoelectric films.
- 29 November 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (3) , 1900626
Open AccessToward Thick Piezoelectric HfO2‐Based Films
For HfO2‐based films, which are mainly prepared by atomic layer deposition, the desired ferroelectric (FE) properties typically vanish while extending the thickness beyond a limit of about 50 nm. Herein, the successful fabrication of a 1 μm‐thick piezoelectric La:HfO2 film is demonstrated using chemical solution deposition, paving the way toward sensor and actuator applications. After identifying the optimal La content, the film thickness is increased from 45 nm to 1 μm. Polarization and strain measurements evidence the persistence of the FE properties at all thicknesses and even a slight improvement due to a better orientation of the polar axis at higher thicknesses. Scanning electron microscopy and X‐ray reflectivity reveal a fine‐grained microstructure and a density of only 80% of the theoretical value, which seems to be a common issue of solution‐deposited HfO2‐based films, based on the performed literature survey. Using tilt‐angle‐dependent X‐ray diffraction scans, homogeneous nucleation is found to be the likely root cause of the observed microstructure. It is suggested that this microstructure issue is key for the optimization of cycling stability of solution‐based films to exploit the full potential of the HfO2 for cost‐efficient, thick piezoelectric films.
- 1 April 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 783, 801-805
Inkjet-printed silver as alternative top electrode for lead zirconate titanate thin films
- 1 April 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 783, 801-805
Inkjet-printed silver as alternative top electrode for lead zirconate titanate thin films