LWLukas Wojarski

Lukas Wojarski

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lukas Wojarski has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Diffusion brazing using powder mixtures of the CoCrFeNi MEA and low melting additives

    by Laura Bültena, Merle Hansen, Wolfgang Tillmann, Lukas Wojarski

    Conventional nickel-based filler alloys for brazing commonly require low melting elements like boron or phosphorus to reduce the required brazing temperature. However, these elements often promote the formation of brittle intermetallic compounds (IMC), which can significantly reduce the joint strength. The reduction in strength is strongly dependent of the gap width as it influences the ratio of melting point depressing elements content to the faying surface area. This leads to a limitation of the maximum applicable joint gap. High entropy alloy (HEA) filler alloys could be an innovative engineering solution to overcome the technical restriction and to produce strong joints even with wider mounting gaps. This can be attributed to the tendency of HEA to form stable solid solutions that feature a high thermal and chemical stability instead of forming brittle intermetallic compounds. Therefore, it is expected that a HEA microstructure in the brazed metal leads to an improvement of the mechanical properties of the brazed joint. Unfortunately, HEA tend to have high melting temperatures, which impedes their application as brazing filler alloy. Therefore, this study presents a novel approach, in which a medium entropy alloy (MEA) consisting of pre alloyed CoCrFeNi-powder is mixed with various melting point depressants (MPDs), which melts at the brazing temperature and forms a HEA microstructure during isothermal solidification. The influence of different MPD concentrations and brazing temperatures on the resulting joint microstructure were analyzed and evaluated.

  • Open Access

    From Campus to Real-World Contexts: Transforming Higher Education with GamBLe EduCache

    by Annika Kunz, Berit Tottmann, Lukas Wojarski, Klaus Jebbink

    This paper presents GamBLe EduCache, an innovative educational initiative that integrates geocaching and gamification elements into university teaching. The project supports first-year students while promoting active learning and interdisciplinary engagement. Students analyze materials and processes at industrial and historical sites through cache-based activities, enhancing their digital competencies via a digital learning platform while supplementing traditional coursework with practical, location-based experiences. The project operates on two levels: providing structured learning opportunities for first-year students through pre-designed caches, and engaging advanced students in creating their own educational caches. The gamification approach incorporates competitive elements to motivate teamwork and active participation. Initial evaluation results show positive outcomes, with high rates of reported learning success and strong support for the gamification approach. Through partnerships with museums and archives, GamBLe EduCache creates a broader educational network that bridges academic theory with practical heritage work while making materials available as OER.

  • Open Access

    Microstructure and properties of conventional and hybrid joints of IN718 brazed with VZ2177

    by Lukas Wojarski, Julia Bültena, Fabian Frittgen, Wolfgang Tillmann

    Brazing hybrid joints of additively manufactured and conventionally produced components made of IN718 opens new application possibilities for additive manufacturing processes, such as PBF-LB/M, in industrial production processes. The combination of hybrid structures enables cost-effective production of large-volume parts with complex features. In this work, the differences between hybrid and conventional joints are analysed, due to the different microstructure of additive manufactured IN718 compared to bulk material. The differences in the microstructures lead to different diffusion paths of the elements from the molten braze alloy along the grain boundaries and to different wetting behaviors. This has a significant effect on the microstructure and the mechanical properties of the joints. To investigate the effect of the microstructure of PBF-LB/M base materials on the brazing of IN718 with the braze alloy VZ2177, vacuum brazing with varying dwell time has been employed to manufacture joints of the bulk material and hybrid joints, consisting of additively manufactured and bulk IN718. Due to the phosphorus in the filler metal, brittle phases in the center of the brazing zone have formed in both joint types. With increasing brazing, the width of the brazing area grew. In the hybrid joint, a strong formation of IMC phases could be observed at the PBF-LB/M side of the joint leading to a higher hardness, which was more pronounced at longer brazing times. The increase in hardness was accompanied with a crack formation that was located near the PBF-LB/M-side only in those hybrid joints with long brazing time and occurred most probably due to stress relief during cooling.


  • Open Access

    Effects of vacuum brazing on microstructure and pseudoelasticity of NiTi shape memory alloy brazements

    by Lukas Wojarski, Alexa Nebel, Wolfgang Tillmann

    NiTi shape memory alloys exhibit pseudoelasticity, allowing them to fully recover from prior deformations under varying thermal or mechanical loads. Unlike conventional materials like steels, these alloys can endure elastic strain rates up to ten times higher, owing to a diffusion-free transformation between the austenite and martensite phases in their crystal lattice induced by temperature or stress. Given their material properties, NiTi shape memory alloys find applications as actuators, implants, and stents, demanding high reliability and biocompatibility standards. To maintain maximum pseudoelasticity when joining NiTi components, any microstructural changes have to be kept to a minimum. In this regard, vacuum brazing is a promising joining technique, as it is capable to produce joints at comparatively low joining temperatures without melting the base material. Hence, this paper is aimed at evaluating the influence of different holding times and brazing temperatures on the deformation behavior of NiTi alloys in vacuum brazing applying AgCuTi braze alloy. For this purpose, microstructural analyses by means of SEM and EDS as well as tensile tests were conducted. Furthermore, the fracture surfaces were analyzed by SEM. It could be observed that a stress plateau was present in the brazed samples leading to the assumption that brazing with AgCuTi is a suitable joining technique to preserve the properties of NiTi. Nevertheless, the brazed samples fractured in the stress plateau.


  • Integration of Digital Laboratories into a Course and e-exam on the Fundamentals on Materials Technology

    by Joana Eichhorn, Henrik Ulitzka, Lukas Wojarski, Julia Mergner, Tobias R. Ortelt

  • Open Access

    In situ observation of the pore formation during laser-based reactive air brazing of alumina

    by Lukas Wojarski, Henrik Ulitzka, Anna Geldmacher, Tim Ulitzka, Wolfgang Tillmann

    Reactive air brazing (RAB) is a low-cost process for joining ceramic composites in air. However, due to the comparably low strength values that can be achieved by RAB, the process is only used in special applications like solid oxide fuel cells as a sealant. The limited strength values are the result of a severe pore formation during the brazing operation that remain in the brazing fillet after the solidification of the brazing filler. In this work, the formation of the pores during RAB brazing of alumina using a paste containing Ag4CuO powder and various binders was investigated. The formation and evolution of the pores were observed and quantified in in situ X-ray measurements. It could be observed that during debinding, pores have developed in the filler metal. The pore structure depends on the binder and the heating rate in the debinding stage. With the melting of the filler metal, many pores are closed by the melt flow. But it seems that the wetting of the alumina was hindered by the pores. The change of porosity during cooling is comparatively low.

  • Open Access

    The Influence of Low-Pressure Plasma Treatments on the Lap Shear Strength of Laser-Joined AISI 304 Hybrids with Polypropylene and Polyamide 6.6

    by Wolfgang Tillmann, Lukas Wojarski, Christian Hopmann, Patricia Fatherazi, Christian Timmer

    This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser-joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304–polyamide 6.6 and sandblasted AISI304–polypropylene hybrids were developed at 2.85 MPa and 4.22 MPa, respectively. The surface free energy was doubled for all used plasma gases to a value of ca. 80 mN m−1 at 180 s. The plasma-treated samples were joined and tested. The arithmetic means of the plasma-treated hybrids’ lap shear strength with polyamide 6.6 varied slightly, but all measured values were within the range of the untreated samples. Residue on the sheared metal samples indicated covalent bonds between AISI304 and polyamide 6.6. The lap shear strengths of the plasma-treated polypropylene hybrids were significantly reduced between −30.8% and −53.3%, depending on the used plasma gas. This was attributed to the over-aging and development of low-molecular-weight oxidized materials, which led to a weak boundary layer. No residue of polypropylene was found on treated or untreated lap shear samples. No correlation between the surface free energy and lap shear strength could be found.


  • Open Access

    Influence of Metallic Interlayers on the Lap Shear Strength of Laser Joined Plastic and Metal Hybrids

    by Wolfgang Tillmann, Lukas Wojarski, Christian Hopmann, Patricia Fatherazi, Christian Timmer

    The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.


  • Open Access

    Influence of Low-Pressure Plasma Treatments on the Lap-Shear Strength of Laser Joined AISI 304 Hybrids with Polypropylene and Polyamide 6.6

    by Wolfgang Tillmann, Lukas Wojarski, Christian Hopmann, Patricia Fatherazi, Christian Timmer

    This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.