Mingming Fu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mingming Fu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jing Xu
Administrative Examination and Approval Authority, Binzhou 256600, China
1 shared publication - Jingyu Wang
School of Environment and Safety Engineering, North University of China, Taiyuan 030051, China
1 shared publication - Lanjuan Xu
Shandong Key Laboratory of Eco-Environmental Science for the Yellow River Delta, Shandong University of Aeronautics, Binzhou, Shandong, 256603, China
1 shared publication Ting Wang
Binzhou University, Chemical Engineering and Safety Department, Shandong Binzhou 256600, China
1 shared publication- Xinlei Jia
College of Chemical Engineering and Safety, Binzhou University, Binzhou 256600, China
1 shared publication - Yaping Li
Binzhou University
1 shared publication
Latest Publications
- Open Access
Preparation and Molecular Dynamics Simulation of RDX/MUF Nanocomposite Energetic Microspheres with Reduced Sensitivity
In order to improve the general problem of irregular coating morphology and low mechanical strength of the coating layer in existing coating desensitization technology, nano-cyclotrimethylene trinitramine/melamine-urea-formaldehyde (RDX/MUF) composite energetic microspheres were prepared by an improved emulsion polymerization, taking the MUF as the binder and RDX as the main explosive. In order to judge whether RDX/MUF possessed good stability, the combination of differential scanning calorimetry (DSC) and molecular dynamics (MD) simulation was used to determine the level of binding binding energy between urea-formaldehyde resin binder (UF) and RDX. In addition, to investigate the optimal reaction temperature for the preparation of MUF/RDX, the binding energy between UF and RDX at different temperatures was simulated. And then the morphology and thermal properties of the as-prepared composite energetic microspheres were analyzed by scanning electron microscopy (SEM) and DSC, the impact sensitivity and friction sensitivity of the resultant samples were tested as well. Moreover, RDX/MUF with the same MUF content was prepared by physical mixing for comparative analysis. MD simulation demonstrated that UF and RDX possessed good binding ability at 298 K. The DSC method indicatec that UF and RDX had good compatibility, and the comprehensive performance of RDX after coating was not significantly deteriorated; The optimal binding temperature between UF and RDX was 60~70 °C which is consistent with the experimental results. The experimental results showed that the optimum process conditions for the preparation of RDX/MUF could be listed as follows: the temperature for preparing RDX/MUF composite energetic microspheres by the improved emulsion polymerization was 70 °C the optimal pH value of the urea-formaldehyde resin prepolymer solution was 3, and the optimal melamine-urea molar ratio was 0.4.
Open AccessPreparation and Molecular Dynamics Simulation of RDX/MUF Nanocomposite Energetic Microspheres with Reduced Sensitivity
In order to improve the general problem of irregular coating morphology and low mechanical strength of the coating layer in existing coating desensitization technology, nano-cyclotrimethylene trinitramine/melamine-urea-formaldehyde (RDX/MUF) composite energetic microspheres were prepared by an improved emulsion polymerization, taking the MUF as the binder and RDX as the main explosive. In order to judge whether RDX/MUF possessed good stability, the combination of differential scanning calorimetry (DSC) and molecular dynamics (MD) simulation was used to determine the level of binding binding energy between urea-formaldehyde resin binder (UF) and RDX. In addition, to investigate the optimal reaction temperature for the preparation of MUF/RDX, the binding energy between UF and RDX at different temperatures was simulated. And then the morphology and thermal properties of the as-prepared composite energetic microspheres were analyzed by scanning electron microscopy (SEM) and DSC, the impact sensitivity and friction sensitivity of the resultant samples were tested as well. Moreover, RDX/MUF with the same MUF content was prepared by physical mixing for comparative analysis. MD simulation demonstrated that UF and RDX possessed good binding ability at 298 K. The DSC method indicatec that UF and RDX had good compatibility, and the comprehensive performance of RDX after coating was not significantly deteriorated; The optimal binding temperature between UF and RDX was 60~70 °C which is consistent with the experimental results. The experimental results showed that the optimum process conditions for the preparation of RDX/MUF could be listed as follows: the temperature for preparing RDX/MUF composite energetic microspheres by the improved emulsion polymerization was 70 °C the optimal pH value of the urea-formaldehyde resin prepolymer solution was 3, and the optimal melamine-urea molar ratio was 0.4.
- Open Access
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012088
Effect of microcapsule layout on crack repair
Similar rock specimens without microcapsules were prepared on the basis of similarity principle, and uniaxial compression tests were carried out to obtain the general law of rock fracture propagation. Microcapsules were mixed into rock specimens in three ways. The first way is uniform mixing. The second method is to add microcapsules at different levels. The third way is to add microcapsules along the crack propagation angle. The uniaxial preloading tests were carried out to obtain the compressive strength of the microcapsules. After the curing of 7d and 14d, three specimens were subjected to compressive test again and the strength recovery rate was calculated. Draw the following conclusions: after pre-compression repair, the compressive strength increases, indicating that microcapsules play a repair role; adding microcapsules along the average angle of crack propagation is the best way to repair the crack; the stress-strain curves show good elastic-plastic, the pressure relief curve is stable, and the residual strength is stable.
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012088
Open AccessEffect of microcapsule layout on crack repair
Similar rock specimens without microcapsules were prepared on the basis of similarity principle, and uniaxial compression tests were carried out to obtain the general law of rock fracture propagation. Microcapsules were mixed into rock specimens in three ways. The first way is uniform mixing. The second method is to add microcapsules at different levels. The third way is to add microcapsules along the crack propagation angle. The uniaxial preloading tests were carried out to obtain the compressive strength of the microcapsules. After the curing of 7d and 14d, three specimens were subjected to compressive test again and the strength recovery rate was calculated. Draw the following conclusions: after pre-compression repair, the compressive strength increases, indicating that microcapsules play a repair role; adding microcapsules along the average angle of crack propagation is the best way to repair the crack; the stress-strain curves show good elastic-plastic, the pressure relief curve is stable, and the residual strength is stable.