TDTapobrata Dey

Tapobrata Dey

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tapobrata Dey has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative analysis of sequential port fuel injection and conventional manifold fuel injection using 10% HCNG blends

    by Ravikant Nanwatkar, Vishal Meshram, Pravin Nitnaware, Tapobrata Dey, Sandeep Sarnobat, Shyamsing Thakur

    Present research examines the relative performance, combustion and emission properties of a 10% HCNG (hydrogen-enriched compressed natural gas) blend in Sequential Port Fuel Injection (SPFI) and Conventional Manifold Fuel Injection (CMFI) engines. The experiments were performed under the conditions of the Wide-Open Throttle (WOT) at the Maximum Brake Torque (MBT) spark timing with a range of engine speeds of 2000 to 4000 rpm. The same was done online by blending Hydrogen with CNG to provide a similar mixture preparation in both modes of injection. The findings show that SPFI has a great improvement in the efficiency of the engine and combustion performance over CMFI. A 15.87% improvement by CMFI was a 16.06% brake thermal efficiency of SPFI at 4000 rpm. There was an increase in volumetric efficiency of about 20% in SPFI mode and a decrease in brake-specific fuel consumption at all the speeds that were tested. It was found that the peak cylinder pressure (34.9 bar) of SPFI was higher than 27 bar in CMFI, which also shows enhanced homogeneity of the mixture and quicker flame spread. The accumulation of emission analysis revealed a significant decrease in CO (19.17) and HC (>50) emissions with SPFI, but the whole of NOx emission growth was attributed to the high in-cylinder temperature that comes with hydrogen enrichment. In general, SPFI exhibits high thermo-chemical efficiency and cleaner combustion properties in terms of using 10% of HCNG mixtures, which underlines its applicability in the field of sustainable use of alternative fuels.

  • Open Access

    Combustion dynamics, emission characteristics and error analysis of hydrogen-blended CNG fuelled SI engine under variable operating conditions

    by Pravin Nitnaware, Vishal Meshram, Ravikant Nanwatkar, Vivek Ghulaxe, Sandeep Sarnobat, Tapobrata Dey, Nitish Hirulkar, Shyamsing Thakur

    The use of alternative fuels over fossil in the spark-ignition engines is critical in reducing the emission of greenhouse gases and energy sustainability. hydrogen compressed natural gas has high flame speed, a wide range of flammability and zero carbon content, allows it to burn much faster and have clean combustion. But in practice, it has knock tendency, NOx formation, loading and speed calibration problems. Here comprehensive analysis of the errors, combustion dynamics and emission characterization of an HCNG-fuelled SI engine that has 0-20 % hydrogen fractions is studied. Statistical error quantification, pressure crank angle analysis, combustion phasing and exhaust measurements were used to confirm trends. It was found that the enrichment of hydrogen reduced the time of combustion, in in-cylinder pressure, and brake thermal efficiency, and lowered the brake specific energy consumption. A 5% H2 was the optimal mixture, with best efficiency-emission tradeoff, reducing CO and HC, and with controllable NOx. Sequential port fuel injection enhanced stability and reduced backfire and able to operate lean-burn without altering hardware. Numerically, the gains were noted to be supported by quantified uncertainties, with 5% HCNG showing a formidable threshold of a stable, efficient, and cleaner SI operation and guiding the deployment of HCNG.

  • Experimental investigation of coating application on excavator bucket

    by Yogesh R. Khedkar, Vinay A. Kulkarni, Tapobrata Dey

    The durability and productivity of the bucket in any earthmoving machine is crucial for enhancing the performance of the machine. These buckets are frequently exposed to harsh environments, leading to rapid wear of the bucket material and component failure. This increases machine downtime and affects customers in terms of time and money. Therefore, the primary concern with excavator buckets is material wear. This study aimed to investigate the effectiveness of ceramic coating in reducing the wear rate of a bucket subjected to harsh environments. Another concern with the excavator bucket is productivity. During digging operations, wet soil adheres to the inner surface of the bucket and affects productivity. Therefore, this study was extended to understand the effect of hydrophobic coating on avoiding soil stickiness to the inner shell of the bucket. In this study, the outer surface of the bucket was coated with an epoxy ceramic coating, and the inner surface of the bucket was coated with a hydrophobic coating. The coated and non-coated buckets were tested under two different soil conditions (Type A and Type C) for 500 h. For type C soil, a 13.5% improvement was observed in the coated bucket compared to the non-coated bucket. The observed 13.5% reduction in wear is a strong indicative trend; however, it represents a preliminary result, and further controlled studies with multiple replicates are required to establish statistical confidence. However, for type A soil, the ceramic coating was not effective for wear resistance. In both soil conditions, the hydrophobic coating was not useful as the material adhered to the bucket inner shell. The ceramic coating samples were observed under FESEM (field-emission scanning electron microscopy (FESEM) and energy-dispersive spectroscopy (EDS) to understand the surface morphology, particle sizes, porosity, and quantitative compositions. This study aims to contribute to the development of high-performance excavator buckets that are more durable and efficient using epoxy coating technology.


  • Aluminum alloy and galvanized steel CMT weld joints for lightweight automobile applications

    by Bhagyashri Zope, Tapobrata Dey, Vijaykumar S Jatti, Sandeep S Sarnobat

    Cold Metal Transfer (CMT) lap joint of Al6061-T6 and Galvanized steel is studied in this paper using design of experiments method. Welding parameters considered for the work includes stick out distance (10 mm −14 mm), wire-feed speed (3.5 m min −1 – 4 m min −1 ) and torch angle (10˚ to 15˚). Weld strength is optimized by using Taguchi analysis by optimizing input variables with 100% argon gas and stick out distance of 14 mm and overlap region of 13 mm. Weldments were cut in shape and size as per ASTM E8 to perform uni-axial tensile test. Further ANOVA analysis is used to understand the effect of individual parameters & their contribution on weld strength. Result depicted all three input parameter significantly effects the strength. Experiments showed that Al6061-T6 is possible to be welded with the Galvanized-steel using CMT.


  • Use of electronic viscous drive to optimize fan duty cycle

    by Dhiraj Ramdas, Tapobrata Dey

    The Electronic Viscous Fan Drive Clutch is one of the key components of cooling system in automotive sectors. It is more efficient than the current traditional bimetal operated Mechanical Viscous Fan Drive Clutch in terms of fan power consumption. The comparative change in fan power with both fan drives is studied and it is observed that with electronic fan clutch 86% reduction in fan power is achieved. In the current study an attempt is made to demonstrate the improvement in the cooling system in terms of ambient temperature of air and the coolant temperature. This is achieved through the complete driving cycles by maintaining unvarying temperature. Standard rise over ambient vehicle test with support of Vector CANape is utilized for testing and data recording. With use of electronic viscous fan drive there is direct proportional relation between coolant temperature and fan rpm. It also indicates that the system level temperatures are optimized to achieve higher efficiency in terms of thermal and fuel economy.


  • Open Access

    Study of PEM Fuel Cell End Plate Design by Structural Analysis Based on Contact Pressure

    by Tapobrata Dey, Jaydeep Deshpande, Debanand Singdeo, Prakash C. Ghosh

    A fuel cell stack is configured to power any load ranging from watts to megawatt by varying cells connected in series. During stack assembly, major emphasis must be placed on application of adequate external pressure for reducing the ohmic losses, the purpose of which is to achieve proper contact between the cell components and minimize the contact resistance. Present work aims to study the influence of geometry of the cell, bolt configuration, gasket thickness mismatch, and material properties of different components of average and distribution contact pressure. The geometries are evaluated for end plate designs with a view to understand the pressure distribution and contact resistance in each case. Among different designs, extruded hexagon is found to perform well with an average contact pressure of 0.13 MPa and contact resistance of 28 Ω-cm2. Greater gasket thickness requires higher forces to be applied before the GDL makes contact with BPP. The effect of gasket thickness mismatch is evaluated for different values to identify its appropriate value. The pressure is applied using bolts and position and number of bolts is determined for homogeneous contact pressure on the active area. This study provides a framework for future end plate design of fuel cells.


  • Open Access

    Packaging Design, Weld Fatigue analysis and Validation of Diesel Exhaust After-treatment System

    by Sonal Nareddiwar, Tapobrata Dey, R. Sunilkumar

    Diesel exhaust after treatment system is usually designed to meet stringent packaging constraints and emission norms. After treatment packaging has critical impact on the overall system efficiency and durability since many components in exhaust systems have welded joints. An after treatment inlet and outlet tube joints, connected to engine outlet and Original Equipment Manufacturer (OEM) tailpipe respectively are subjected to vibrations and bending moment leading to fatigue failure at the inlet/outlet welded joints. It has been observed over the years that the prevailing failure modes in after treatment systems are cracked welds at joints between inlet tubes and flanges, outlet tubes and connecting tailpipes. Fatigue failure is a complex and progressive form of local damage which occurs in welded components of exhaust after-treatment systems. Thus, this fatigue failure needs to be estimated accurately and at the early stage of design to save cost and time. But due to geometrical irregularities, compact packaging design and load transfer conditions, it becomes difficult to estimate accurate fatigue strength of the welded areas. Thus weld fatigue analysis, a high cycle fatigue test to validate inlet/outlet module of exhaust system against dynamic overturning bending moment and to calculate the location of minimum weld fatigue life within the inlet welded joints is performed. Weld fatigue analysis uses advanced fatigue assessment technique, BS 7608, Stress x Life (S x N) approach for accurate and precise estimation of welds. The present work deals with reducing the package volume of the after treatment system by applying different concepts, verifying design robustness by FEA simulation using ANSYS 18.2 and validating the structural durability of the system by testing. The objective of the present work is to estimate the fatigue life of the welded structures precisely and accurately, calculate the threshold bending moment to determine whether the design is robust to the bending moment loads seen over course of its life and make design modifications as per simulation result. Further the FEA and testing results of weld fatigue analysis are correlated.


  • Open Access

    Study of Shell and Tube Heat Exchanger with the Effect of Types of Baffles

    by Pranita Bichkar, Ojas Dandgaval, Pranita Dalvi, Rhushabh Godase, Tapobrata Dey


  • A new modified-serpentine flow field for application in high temperature polymer electrolyte fuel cell

    by Debanand Singdeo, Tapobrata Dey, Shrihari Gaikwad, Søren Juhl Andreasen, Prakash C. Ghosh


  • Phosphoric acid doped poly(2,5‐benzimidazole)‐based proton exchange membrane for high temperature fuel cell application

    by Ratikanta Nayak, Tapobrata Dey, Prakash C. Ghosh, Arup R. Bhattacharyya

    Undoped and doped poly(2,5‐benzimidazole) (ABPBI) membrane was prepared by solvent casting method using methane sulfonic acid as a solvent and phosphoric acid (H3PO4) as a doping agent. The concentration of H3PO4 was varied from 0 to 60 vol% to enhance the proton conductivity of the ABPBI membrane at higher temperature. Wide angle X‐ray diffraction analysis showed a decrease in crystallinity in ABPBI membrane with increase in H3PO4 doping concentration. The molecular signature and the presence of H3PO4 was observed in 1000–1500 cm−1 in the Fourier transform infrared spectra, which was also supported by a corresponding weight loss at 180°C–200°C in the thermogravimetric analysis. Undoped ABPBI membrane registered the Young's modulus (E) and hardness (H) values of 2.46 and 0.92 GPa, respectively, and the corresponding E and H values for 1.65 doping level of 60 vol% H3PO4 doped ABPBI membrane were 0.14 and 0.067 GPa, respectively. The 60 vol% H3PO4 doped ABPBI membrane with doping level of 1.65 showed highest proton conductivity value of 2.2 × 10−2 S/cm. The impedance spectroscopic analysis and the equivalent circuit model were discussed to understand the nature of proton conduction in H3PO4 doped ABPBI membrane. POLYM. ENG. SCI., 56:1366–1374, 2016. © 2016 Society of Plastics Engineers