TPTatiana Pogarskaia

Tatiana Pogarskaia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tatiana Pogarskaia has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Customization of the Geodesic Algorithm for Optimal Fastener Arrangement

    by Julia Shinder, Margarita Petukhova, Sergey Lupuleac, Tatiana Pogarskaia

  • Application of HPC for Simulation of Sealant Influence on the Aircraft Assembly Process

    by Artem Eliseev, Sergey Lupuleac, Julia Shinder, Tatiana Pogarskaia, Margarita Petukhova

  • ECMI Modelling Week: First Time in Russia and First Time Online

    by Tatiana Pogarskaia, Sergey Lupuleac, Matti Heiliö

  • Optimization of the Installation Sequence for the Temporary Fasteners in the Aircraft Industry

    by Tatiana Pogarskaia, Sergey Lupuleac, Julia Shinder, Philipp Westphal

    Riveting and bolting are common assembly methods in aircraft production. The fasteners are installed immediately after hole drilling and fix the relative tangential displacements of the parts that took place. A proper fastener sequence installation is very important because a wrong one can lead to a “bubble-effect” when gap between parts after fastening becomes larger in some areas rather than being reduced. This circumstance affects the quality of the final assembly. For that reason, the efficient methods for determination of fastening sequence taking into account the specifics of the assembly process are needed. The problem is complicated by several aspects. First of all, it is a combinatorial problem with uncertain input data. Second, the assembly quality evaluation demands the time-consuming computations of the stress–strain state of the fastened parts caused by sequential installation of fasteners. Most commonly used strategies (heuristic methods and approximation algorithms) require a large number of computational iterations what dramatically complicates the problem. The paper presents the efficient methods of fastener sequence optimization based on greedy strategy and the specifics of the assembly process. Verification of the results by comparison to commonly used installation strategies shows its quality excellence.


  • DEVELOPMENT OF SOFTWARE COMPLEX FOR ANALYSIS AND OPTIMIZATION OF THE AIRCRAFT ASSEMBLY PROCESS

    by Nadezhda I. Zaitseva, Tatiana A. Pogarskaia

    Данная статья посвящена описанию многопроцессорного программного комплекса ASRP (Assembly Simulation of Riveting Process), разрабатываемого в рамках совместного проекта Санкт-Петербургского Политехнического университета Петра Великого и концерна AIRBUS. Этот комплекс предназначен для моделирования и оптимизации процесса сборки самолётов с учетом того, что в авиастроении из-за высоких эксплуатационных нагрузок к качеству сборки деталей предъявляются достаточно жёсткие требования. В комплексе ASRP предлагается использовать методы математического моделирования и численной оптимизации, которые позволяют предсказать и оптимизировать качество соединения деталей еще до внедрения разрабатываемых технологий на сборочную линию. В авиастроении при серийной сборке одна и та же сборочная технология используется для всех собираемых самолётов одного типа. Соответственно, при моделировании процесса сборки нужно учитывать случайные сборочные отклонения, такие как отклонения деталей от номинальной формы или погрешности их позиционирования и закрепления на сборочных стендах. В ASRP предлагается учитывать эти отклонений через моделирование случайного начального зазора между деталями. Для оптимизации процессов сборки требуется создавать и анализировать разные варианты расположения фиксирующих элементов. Для ASRP разработан принципиально новый подход к оптимизации расстановок крепежных элементов, основанный на предварительной оценке напряженно деформированного состояния собираемой конструкции. При моделировании сборочных процессов с учетом сборочных отклонений и оптимизации расстановок крепежных элементов возникает необходимость решения множества однотипных задач с сотнями вариантов начальных данных. По этой причине для анализа и оптимизации сборочных процессов в ASRP предложено использовать параллельные вычисления. В данной статье описывается структура разрабатываемого программного комплекса ASRP, разработанные методы моделирования сборочного процесса и методы моделирования начального зазора, а также предложенные методы оптимизации расстановки крепежных элементов. Эффективность использования предложенных методов оптимизации и алгоритмов распараллеливания исследуется на практическом примере, связанном с анализом процесса сборки хвостового соединения самолета Airbus...


  • RED WoLF hybrid storage system: Adaptation of algorithm and analysis of performance in residential dwellings

    by Michael Wiesheu, Luka Rutešić, Alexander Alexandrovich Shukhobodskiy, Tatiana Pogarskaia, Aleksandr Zaitcev, Giuseppe Colantuono


  • RED WoLF hybrid storage system: Comparison of CO2 and price targets

    by Alexander Alexandrovich Shukhobodskiy, Aleksandr Zaitcev, Tatiana Pogarskaia, Giuseppe Colantuono


  • Optimization of fastener pattern in airframe assembly

    by Sergey Lupuleac, Tatiana Pogarskaia, Maria Churilova, Michael Kokkolaras, Elodie Bonhomme

    Purpose: The authors consider the problem of optimizing temporary fastener patterns in aircraft assembly. Minimizing the number of fasteners while maintaining final product quality is one of the key enablers for intensifying production in the aerospace industry. The purpose of this study is to formulate the fastener pattern optimization problem and compare different solving approaches on both test benchmarks and rear wing-to-fuselage assembly of an Airbus A350-900. Design/methodology/approach: The first considered algorithm is based on a local exhaustive search. It is proved to be efficient and reliable but requires much computational effort. Secondly, the Mesh Adaptive Direct Search (MADS) implemented in NOMAD software (Nonlinear Optimization by Mesh Adaptive Direct Search) is used to apply the powerful mathematical machinery of surrogate modeling and associated optimization strategy. In addition, another popular optimization algorithm called simulated annealing (SA) was implemented. Since a single fastener pattern must be used for the entire aircraft series, cross-validation of obtained results was applied. The available measured initial gaps from 340 different aircraft of the A350-900 series were used. Findings: The results indicated that SA cannot be applicable as its random character does not provide repeatable results and requires tens of runs for any optimization analysis. Both local variations (LV) method and MADS have proved to be appropriate as they improved the existing fastener pattern for all available gaps. The modification of the MADS' search step was performed to exploit all the information the authors have about the problem. Originality/value: The paper presents deterministic and probabilistic optimization problem formulations and considers three different approaches for their solution. The existing fastener pattern was improved.