Boyan I. Mihaylov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Boyan I. Mihaylov has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Evan C. Bentz
Department of Civil and Mineral Engineering, University of Toronto, Toronto, Canada
5 shared publications - Alexandru N. Trandafir
University of Liège
4 shared publications Michael P. Collins
4 shared publications- Chathura Rajapakse
University of Kelaniya
2 shared publications - Jaime Mata-Falcón
ETH Zurich
2 shared publications - Jian Liu
Department of ArGEnCo and Research Unit of Urban and Environmental Engineering University of Liege Liege Belgium
2 shared publications
Latest Publications
- Open Access
- 23 June 2026
- Published by Wiley in Structural Concrete
- Vol. 27 (5) , 7727-7745
Experimental and analytical investigations on the effect of steel fibers on the crack behavior and strength of dapped‐end connections
Reinforced concrete (RC) dapped‐end connections feature a sharp re‐entrant corner subjected to high stress concentrations, leading to wide cracks under service loads and potential durability issues such as reinforcement corrosion. Effective crack control is therefore essential in the design of new dapped‐end connections. Steel fiber reinforced concrete (SFRC) has shown potential to improve crack control while also enhancing ultimate strength. This study proposes a kinematics‐based model to describe the response of SFRC dapped ends along the re‐entrant corner crack. Appropriate constitutive relationships are used to link the deformations along the corner crack and the compression zone to the resisting forces: reinforcement and SFRC in compression and tension. The model is validated against eight large‐scale tests with varying fiber amounts including detailed deformation measurements from which the resisting mechanisms and crack‐opening behavior are derived. The experimental results show that a fiber amount of 70 kg/m 3 reduces the crack width by about 40%, enabling compliance with code requirements. The validation demonstrates that the proposed model represents a reliable tool for designing SFRC dapped‐end connections at both service and ultimate limit states.
- 23 June 2026
- Published by Wiley in Structural Concrete
- Vol. 27 (5) , 7727-7745
Open AccessExperimental and analytical investigations on the effect of steel fibers on the crack behavior and strength of dapped‐end connections
Reinforced concrete (RC) dapped‐end connections feature a sharp re‐entrant corner subjected to high stress concentrations, leading to wide cracks under service loads and potential durability issues such as reinforcement corrosion. Effective crack control is therefore essential in the design of new dapped‐end connections. Steel fiber reinforced concrete (SFRC) has shown potential to improve crack control while also enhancing ultimate strength. This study proposes a kinematics‐based model to describe the response of SFRC dapped ends along the re‐entrant corner crack. Appropriate constitutive relationships are used to link the deformations along the corner crack and the compression zone to the resisting forces: reinforcement and SFRC in compression and tension. The model is validated against eight large‐scale tests with varying fiber amounts including detailed deformation measurements from which the resisting mechanisms and crack‐opening behavior are derived. The experimental results show that a fiber amount of 70 kg/m 3 reduces the crack width by about 40%, enabling compliance with code requirements. The validation demonstrates that the proposed model represents a reliable tool for designing SFRC dapped‐end connections at both service and ultimate limit states.
- 20 November 2025
- Published by Elsevier in Engineering Structures
- Vol. 348
A kinematics-based model for the shear response of reinforced concrete dapped-end connections
- 20 November 2025
- Published by Elsevier in Engineering Structures
- Vol. 348
A kinematics-based model for the shear response of reinforced concrete dapped-end connections
- 28 April 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (4) , 1-15
Modelling the ultimate shear behaviour of UHPFRC deep beams
- 28 April 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (4) , 1-15
Modelling the ultimate shear behaviour of UHPFRC deep beams
- 14 January 2024
- Published by Elsevier in Engineering Structures
- Vol. 303, 117497
Model for rapid evaluation of corner crack widths in reinforced concrete dapped-end conections
- 14 January 2024
- Published by Elsevier in Engineering Structures
- Vol. 303, 117497
Model for rapid evaluation of corner crack widths in reinforced concrete dapped-end conections
- 3 June 2023
- Published by Springer Nature
- p. 469-478
Crack-Based Modeling of FRP-Reinforced Deep Beams Without Transverse Reinforcement
- 3 June 2023
- Published by Springer Nature
- p. 469-478
Crack-Based Modeling of FRP-Reinforced Deep Beams Without Transverse Reinforcement
- 3 June 2023
- Published by Springer Nature
- p. 352-360
Towards Crack-Based Assessment of Dapped-End Connections
- 3 June 2023
- Published by Springer Nature
- p. 352-360
Towards Crack-Based Assessment of Dapped-End Connections
- 17 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (1) , 956-971
Modeling the behavior of shear‐dominated walls retrofitted with ultra high‐performance fiber‐reinforced concrete jackets
Large‐scale tests of shear‐dominated walls with ultra high‐performance fiber‐reinforced concrete (UHPFRC) jackets have shown the high effectiveness of this retrofitting solution. The jackets can suppress brittle shear failures and result in a ductile response governed by yielding of the flexural reinforcement. In addition, due to the low porosity of UHPFRC and the crack control provided by the fibers, the jackets can also provide an effective corrosion protection. However, while this retrofitting solution is very promising, there is a lack of mechanical models that can predict the effect of UHPFRC jackets. This paper proposes such a model based on a three‐parameter kinematic theory (3PKT) for reinforced concrete walls. The 3PKT is extended by modeling three important effects associated with the UHPFRC jackets: tension in the fibers across the critical diagonal cracks, increased compression resistance of the critical loading zones, and enhanced crack control. The results show that the proposed approach can be used to design the properties of UHPFRC jackets in order to achieve a desired structural response in terms of strength, ductility, and crack control.
- 17 December 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (1) , 956-971
Modeling the behavior of shear‐dominated walls retrofitted with ultra high‐performance fiber‐reinforced concrete jackets
Large‐scale tests of shear‐dominated walls with ultra high‐performance fiber‐reinforced concrete (UHPFRC) jackets have shown the high effectiveness of this retrofitting solution. The jackets can suppress brittle shear failures and result in a ductile response governed by yielding of the flexural reinforcement. In addition, due to the low porosity of UHPFRC and the crack control provided by the fibers, the jackets can also provide an effective corrosion protection. However, while this retrofitting solution is very promising, there is a lack of mechanical models that can predict the effect of UHPFRC jackets. This paper proposes such a model based on a three‐parameter kinematic theory (3PKT) for reinforced concrete walls. The 3PKT is extended by modeling three important effects associated with the UHPFRC jackets: tension in the fibers across the critical diagonal cracks, increased compression resistance of the critical loading zones, and enhanced crack control. The results show that the proposed approach can be used to design the properties of UHPFRC jackets in order to achieve a desired structural response in terms of strength, ductility, and crack control.
- 8 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (1) , 756-770
Detailed crack‐based assessment of a 4‐m deep beam test specimen
When shear cracking occurs in existing reinforced concrete deep members, engineers are faced with the challenge of determining the safety of the members. This paper presents a crack‐based assessment approach that utilizes the Two‐Parameter Kinematic Theory (2PKT) as a framework for the assessment of lightly reinforced concrete deep beams. The paper presents three assessment approaches with progressively increasing levels of approximation (LoAs). The first level of approximation (LoA I) involves using the 2PKT in a predictive manner for situations where the crack shapes are unknown, LoA II improves upon LoA I by incorporating more detailed modeling of the strain in the transverse reinforcement at the location of the critical cracks, and LoA III includes the details of LoA II but also uses the detailed crack geometry as an input in the assessment. Each of the LoAs is presented and compared with experimental data from a 4‐m deep beam test in the literature. The shear carrying mechanisms determined from the kinematic model are evaluated and compared across LoAs. Finally, the paper utilizes LoA III to study the size effect in shear for deep beams. The results quantify the influence of aggregate interlock on the size effect in shear critical deep beams.
- 8 September 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (1) , 756-770
Detailed crack‐based assessment of a 4‐m deep beam test specimen
When shear cracking occurs in existing reinforced concrete deep members, engineers are faced with the challenge of determining the safety of the members. This paper presents a crack‐based assessment approach that utilizes the Two‐Parameter Kinematic Theory (2PKT) as a framework for the assessment of lightly reinforced concrete deep beams. The paper presents three assessment approaches with progressively increasing levels of approximation (LoAs). The first level of approximation (LoA I) involves using the 2PKT in a predictive manner for situations where the crack shapes are unknown, LoA II improves upon LoA I by incorporating more detailed modeling of the strain in the transverse reinforcement at the location of the critical cracks, and LoA III includes the details of LoA II but also uses the detailed crack geometry as an input in the assessment. Each of the LoAs is presented and compared with experimental data from a 4‐m deep beam test in the literature. The shear carrying mechanisms determined from the kinematic model are evaluated and compared across LoAs. Finally, the paper utilizes LoA III to study the size effect in shear for deep beams. The results quantify the influence of aggregate interlock on the size effect in shear critical deep beams.
- 25 August 2022
- Published by Springer Nature
- p. 417-432
Hybrid Simulation Testing of Coupling Beams