IVIvan L. Vialikov

Ivan L. Vialikov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ivan L. Vialikov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Analytical methodology for predicting the strength characteristics of composite materials with a polymer matrix

    by Gennady B. Verzhbovskiy, Alan V. Zaliev, Onuralp Y. Özkılıç, Ivan L. Vialikov

    Introduction. The widespread use of artificial composite materials is impossible without establishing their physical and mechanical properties. To do this, developers are forced to conduct a significant number of diverse experimental studies, varying the percentage ratios of the components of the created material, selecting the optimal composition and properties required for each specific case, which leads to significant material and time expenditures. One possible way to accelerate the composite development process is analytical prediction of their properties. Aim. Develop an analytical method for determining the elastic and strength properties of binary and multicomponent building composite materials that obey the rule of mixture. Materials and methods. This paper examines composite materials consisting of a polymer matrix and one or more fillers. The artificial material is formed by simply mixing all components, which do not chemically react with each other. To develop an analytical method for predicting their strength properties, it is assumed that the composite's properties at the contact surfaces of the matrix and filler are no worse than the parameters of any of the material's components. The matrix properties are assumed to be isotropic and uniform throughout the entire volume of the medium, which is ensured by the mixture preparation technology. The material as a whole and its components obey Hooke's law until any part of the composite, which is a statistical mechanical mixture of the components, fails. Results. Analytical expressions were obtained for determining the elastic and shear moduli, Poisson's ratio, and ultimate strength of two- and multi-component composite materials, allowing for the prediction of the properties of the resulting artificial composite. Conclusions. The obtained expressions demonstrate good agreement between the theoretical characteristics of various known composite materials and their actual properties. This predictive approach allows for a significant reduction in the number of physical experiments required to create new composites and also enables the establishment of upper strength limits for materials with zero porosity.

  • Open Access

    Data measurement system for non-destructive quality testing of hard alloys

    by I. K. Tsybrii, I. L. Vyalikov, V. I. Ignatenko

    Introduction. It is known that the quality of products from sintered hardmetals, if the fabrication technique is not violated, is determined by the phase composition and an average grain size of the carbide phase. However, hard alloys have a disadvantage inherent in all products of powder metallurgy - the inhomogeneity of the structure and the corresponding variation of properties. Traditional methods of monitoring the structure and phase composition according to the results of selective destructive tests prevent from receiving quality data under the production conditions and do not guarantee the identity of the properties of all batch products under study. The major method of non-destructive quality control of hard alloys is coercimetry, but domestic coercimeters are currently not produced. In this regard, the work objective is to create a domestic data measurement system for non-destructive quality testing of hard alloys and an assessment of the reliability of the results obtained with its help. Materials and Methods. Cylindrical and spherangular rods with the diameter of 4 to 10 mm, made of alloys of VK8 and VK10HOM grades, were used in the work. The method of comparison with a certified product was used to determine the coercitive force in the data measuring system. Research Results. The coercive force of two batches of products from hard alloys of VK10HOM and VK8 grades was measured using the developed data measuring system and KOERZIMAT 1.097 HcJ coersimeter. Discussion and Conclusions. The experimental studies show that the values of the coercitive force of the samples obtained on different equipment have approximately the same level. The inhomogeneity of the structure characteristic of sintered hardmetals being a fabrication technique effect is confirmed. Providing that the relative error of measuring the coercitive force for each sample should be within ± 6%, the results obtained can be considered satisfactory. It is shown that the measurement algorithm proposed and implemented in the data measurement system through comparing the characteristics of the tested and certified samples with the known coercitive force, allows the manufacturer of hard alloy products to expand the sample of inspected products up to 100%, and to significantly reduce the costs for non-destructive testing of products.