Farbod Akhavan Niaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Farbod Akhavan Niaki has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Laine Mears
Clemson University
3 shared publicationsAbram Pleta
Clemson University
2 shared publications- Brandt J. Ruszkiewicz
Clemson University Department of Automotive Engineering Greenville, SC
1 shared publication - Elizabeth Gendreau
Department of Mechanical Engineering, Clemson University, Clemson, SC 29607
1 shared publication - Jim A. Bergmann
Virtual Machining, TU Dortmund University, Dortmund, Germany
1 shared publication - Laine Mears
International Center for Automotive Research, Clemson University, Greenville, SC 29607
1 shared publication
Latest Publications
- 7 January 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (5-8) , 1405-1419
Trochoidal milling: investigation of dynamic stability and time domain simulation in an alternative path planning strategy
- 7 January 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (5-8) , 1405-1419
Trochoidal milling: investigation of dynamic stability and time domain simulation in an alternative path planning strategy
- 27 April 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (6)
Electroplastic Drilling of Low- and High-Strength Steels
When postforming machining operations are required on high-strength structural components, tool life becomes a costly issue, often requiring external softening via techniques such as laser assistance for press-hardened steel components. Electrically assisted manufacturing (EAM) uses electricity during material removal processes to reduce cutting loads through thermal softening. This paper evaluates the effect of electric current on a drilling process, termed electroplastic drilling, through the metrics of axial force, and workpiece temperature when machining mild low carbon steel (1008CR steel) and an advanced high strength press hardened steel. A design of experiment (DoE) is conducted on 1008CR steel to determine primary process parameter effects; it is found that electricity can reduce cutting loads at the cost of an increased workpiece temperature. The knowledge generated from the DoE is applied to the advanced high strength steel to evaluate cutting force reduction, process time savings, and tool life improvement at elevated feedrates. It is found that force can be reduced by 50% in high feedrates without observing catastrophic tool failure for up to ten cuts, while tool failure occurs in only a single cut for the no-current condition. Finally, the limitations of the developed model in electroplastic drilling are discussed along with future suggestions for industrialization of the method.
- 27 April 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (6)
Electroplastic Drilling of Low- and High-Strength Steels
When postforming machining operations are required on high-strength structural components, tool life becomes a costly issue, often requiring external softening via techniques such as laser assistance for press-hardened steel components. Electrically assisted manufacturing (EAM) uses electricity during material removal processes to reduce cutting loads through thermal softening. This paper evaluates the effect of electric current on a drilling process, termed electroplastic drilling, through the metrics of axial force, and workpiece temperature when machining mild low carbon steel (1008CR steel) and an advanced high strength press hardened steel. A design of experiment (DoE) is conducted on 1008CR steel to determine primary process parameter effects; it is found that electricity can reduce cutting loads at the cost of an increased workpiece temperature. The knowledge generated from the DoE is applied to the advanced high strength steel to evaluate cutting force reduction, process time savings, and tool life improvement at elevated feedrates. It is found that force can be reduced by 50% in high feedrates without observing catastrophic tool failure for up to ten cuts, while tool failure occurs in only a single cut for the no-current condition. Finally, the limitations of the developed model in electroplastic drilling are discussed along with future suggestions for industrialization of the method.
- Open Access
- 17 January 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 232 (11) , 2030-2043
A probabilistic-based study on fused direct and indirect methods for tracking tool flank wear of Rene-108, nickel-based alloy
Nickel-based alloys are a class of hard-to-machine materials that exhibit a unique combination of high strength at high temperature. While they are widely used in industry, the high tool wear rate of these materials makes machining them a challenging task. Furthermore, machining tolerances, residual stresses, and tool runout impose uncertainty in tracking tool wear. In this work, the current view on tracking progressive tool wear is shifted from deterministic domains into the stochastic domain to study the probability distribution of the tool wear during the process. To do so, Bayesian-based estimation was used for accurate model inference and the result was fed into the Kalman filter for tracking tool wear in end-milling Rene-108 Ni-based alloy. To improve the accuracy, a direct laser measuring system for capturing tool length change was fused with the indirect power measurement. The results show a significant improvement in accuracy over the indirect method, with less than 8 µm root mean square error. This measuring strategy improved the accuracy, while preserving the automated platform for monitoring the tool’s health.
- 17 January 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 232 (11) , 2030-2043
Open AccessA probabilistic-based study on fused direct and indirect methods for tracking tool flank wear of Rene-108, nickel-based alloy
Nickel-based alloys are a class of hard-to-machine materials that exhibit a unique combination of high strength at high temperature. While they are widely used in industry, the high tool wear rate of these materials makes machining them a challenging task. Furthermore, machining tolerances, residual stresses, and tool runout impose uncertainty in tracking tool wear. In this work, the current view on tracking progressive tool wear is shifted from deterministic domains into the stochastic domain to study the probability distribution of the tool wear during the process. To do so, Bayesian-based estimation was used for accurate model inference and the result was fed into the Kalman filter for tracking tool wear in end-milling Rene-108 Ni-based alloy. To improve the accuracy, a direct laser measuring system for capturing tool length change was fused with the indirect power measurement. The results show a significant improvement in accuracy over the indirect method, with less than 8 µm root mean square error. This measuring strategy improved the accuracy, while preserving the automated platform for monitoring the tool’s health.