Artem Aleksandrovich Popov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Artem Aleksandrovich Popov has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Igor Miroslavovich Dobush
50ohm Lab TUSUR, Tomsk State University of Control Systems and Radioelectronics Tomsk Russia
9 shared publications - Andrei Sergeyevich Salnikov
Tomsk State University of Control Systems and Radioelectronics
8 shared publications Alexey A. Kalentyev
50ohm Lab, Tomsk State University of Control Systems and Radioelectronics, 40 Lenina avenue, 634050 Tomsk, Russia
4 shared publications- Dmitry Bilevich
Tomsk State University of Control Systems and Radioelectronics,50ohm Lab,Tomsk,Russia
4 shared publications Dmitry V. Bilevich
50ohm Lab, Tomsk State University of Control Systems and Radioelectronics, 40 Lenina avenue, 634050 Tomsk, Russia
4 shared publicationsAleksandr E. Goryainov
50ohm Lab, Tomsk State University of Control Systems and Radioelectronics, 40 Lenina avenue, 634050 Tomsk, Russia
3 shared publications
Latest Publications
- 20 November 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 66 (7) , 749-755
Effect of Response Approximation on Accuracy of Surrogate Modeling of On-Chip Spiral Inductor
- 20 November 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 66 (7) , 749-755
Effect of Response Approximation on Accuracy of Surrogate Modeling of On-Chip Spiral Inductor
- 11 July 2023
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 37 (2)
A genetic‐algorithm‐based synthesis of microwave integrated distributed amplifiers
This article presents a genetic algorithm‐based technique for microwave integrated distributed amplifier synthesis. To speed‐up synthesis, only linear characteristics are used in the goal function. The technique uses MMIC foundry process design kit models providing manufacturing‐ready schematics to be found. The models from the process design kit are presented as S‐parameters again to enhance algorithm performance. The technique allows searching among most of the existing schematics of the microwave distributed amplifier but is not limited to typical topologies. The section number is theoretically unlimited and makes it possible to find principally new circuit topology. The synthesis shortens and simplifies the distributed amplifier design time. Experimental validation of the technique is carried out by synthesizing the broadband driver stage for the 20–30 GHz buffer amplifier. The technique produces several amplifier topologies meeting the requirements. The most appropriate circuit was manufactured using a commercial 0.25 μm GaAs pHEMT process. The manufactured buffer amplifier demonstrates a gain of 10 dB and 20 dBm output power at a 1 dB compression point.
- 11 July 2023
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 37 (2)
A genetic‐algorithm‐based synthesis of microwave integrated distributed amplifiers
This article presents a genetic algorithm‐based technique for microwave integrated distributed amplifier synthesis. To speed‐up synthesis, only linear characteristics are used in the goal function. The technique uses MMIC foundry process design kit models providing manufacturing‐ready schematics to be found. The models from the process design kit are presented as S‐parameters again to enhance algorithm performance. The technique allows searching among most of the existing schematics of the microwave distributed amplifier but is not limited to typical topologies. The section number is theoretically unlimited and makes it possible to find principally new circuit topology. The synthesis shortens and simplifies the distributed amplifier design time. Experimental validation of the technique is carried out by synthesizing the broadband driver stage for the 20–30 GHz buffer amplifier. The technique produces several amplifier topologies meeting the requirements. The most appropriate circuit was manufactured using a commercial 0.25 μm GaAs pHEMT process. The manufactured buffer amplifier demonstrates a gain of 10 dB and 20 dBm output power at a 1 dB compression point.
- 16 June 2022
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 15 (3) , 465-476
Automatic golden device selection and measurement smoothing algorithms for microwave transistor small-signal noise modeling
We propose the techniques for automatic processing of measurement results in the context of golden (typical) device selection and noise figure measurement. These techniques are for golden (typical) device selection and noise figure measurement processing. Automation of measurement result processing and microwave element modeling speeds up a modeling routine and decreases the risk of possible errors. The techniques are validated through modeling of 0.15 μm GaAs pHEMTs with 4 × 40 μm and 4 × 75 μm total gate widths. Two test amplifiers were designed using the developed models. The amplifier modeling results agree well with measurements which confirms the validity of the proposed techniques. The proposed algorithm is potentially applicable to other circuit types (switches, digital, power amplifiers, mixers, oscillators, etc.) but may require different settings in those cases. However, in the presented work, we validated the algorithm for the linear and low-noise amplifiers only.
- 16 June 2022
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 15 (3) , 465-476
Automatic golden device selection and measurement smoothing algorithms for microwave transistor small-signal noise modeling
We propose the techniques for automatic processing of measurement results in the context of golden (typical) device selection and noise figure measurement. These techniques are for golden (typical) device selection and noise figure measurement processing. Automation of measurement result processing and microwave element modeling speeds up a modeling routine and decreases the risk of possible errors. The techniques are validated through modeling of 0.15 μm GaAs pHEMTs with 4 × 40 μm and 4 × 75 μm total gate widths. Two test amplifiers were designed using the developed models. The amplifier modeling results agree well with measurements which confirms the validity of the proposed techniques. The proposed algorithm is potentially applicable to other circuit types (switches, digital, power amplifiers, mixers, oscillators, etc.) but may require different settings in those cases. However, in the presented work, we validated the algorithm for the linear and low-noise amplifiers only.
- Open Access
- 12 November 2021
- Published by MDPI AG in Electronics
- Vol. 10 (22) , 2775
Development of a 0.15 μm GaAs pHEMT Process Design Kit for Low-Noise Applications
This work presents a process design kit (PDK) for a 0.15 μm GaAs pHEMT process for low-noise MMIC applications developed for AWR Microwave Office (MWO). A complete set of basic elements is proposed, such as TaN thin film resistors and mesa-resistors, capacitors, inductors, and transistors. The developed PDK can be used in technology transfer or education.
- 12 November 2021
- Published by MDPI AG in Electronics
- Vol. 10 (22) , 2775
Open AccessDevelopment of a 0.15 μm GaAs pHEMT Process Design Kit for Low-Noise Applications
This work presents a process design kit (PDK) for a 0.15 μm GaAs pHEMT process for low-noise MMIC applications developed for AWR Microwave Office (MWO). A complete set of basic elements is proposed, such as TaN thin film resistors and mesa-resistors, capacitors, inductors, and transistors. The developed PDK can be used in technology transfer or education.
- 13 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Effect of Different De-Embedding Techniques on Small-Signal Parameters of X-Band Low-Noise Amplifier
In most cases researchers consider existing de-embedding techniques in terms of characterization accuracy of the monolithic microwave integrated circuit component where an emphasis is put on the upper limit of the frequency range. In real practice, when faced with a choice of the de-embedding technique, one must take into account a number of additional factors, such as target application field of the component, manufacturing capabilities and production costs. In this paper we compare existing de-embedding techniques in the context of GaAs pHEMT-based two-stage low-noise amplifier monolithic microwave integrated circuit design. Firstly, we analyze several de-embedding techniques valid for pHEMTs with both coplanar and microstrip accesses and outline differences in de-embedded active bias S-parameters. Then, for each of the considered de-embedding technique we estimated the overall effect on low-noise amplifier small-signal characteristics, the total wafer area occupied by various de-embedding structures and flexibility of a technique regarding characterization of several active and passive devices with different pad distance and feed line length located on the same wafer.
- 13 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Effect of Different De-Embedding Techniques on Small-Signal Parameters of X-Band Low-Noise Amplifier
In most cases researchers consider existing de-embedding techniques in terms of characterization accuracy of the monolithic microwave integrated circuit component where an emphasis is put on the upper limit of the frequency range. In real practice, when faced with a choice of the de-embedding technique, one must take into account a number of additional factors, such as target application field of the component, manufacturing capabilities and production costs. In this paper we compare existing de-embedding techniques in the context of GaAs pHEMT-based two-stage low-noise amplifier monolithic microwave integrated circuit design. Firstly, we analyze several de-embedding techniques valid for pHEMTs with both coplanar and microstrip accesses and outline differences in de-embedded active bias S-parameters. Then, for each of the considered de-embedding technique we estimated the overall effect on low-noise amplifier small-signal characteristics, the total wafer area occupied by various de-embedding structures and flexibility of a technique regarding characterization of several active and passive devices with different pad distance and feed line length located on the same wafer.
- 10 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A Study of Connectors and Feed Lines De-Embedding Techniques for PCB Microwave Components S-Parameters Measurements Up To 50 Ghz
Connectors and lines de-embedding techniques for PCB microwave components S-parameters measurements up to 50 are considered. Comparison between widely used Multiline Thru-Reflect-Line (MTRL) method and promising 2xThru method are presented. This paper has demonstrated that both methods give same results, however, 2xThru method requires just one measured structure as opposite MTRL, where six measured structures are used. The difference between obtained and measured parameters of device under test are less than 0.35 dB in magnitude and 1.5° in phase for insertion loss, and less than 0.08 in magnitude and 10° in phase for return loss at most frequency points.
- 10 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A Study of Connectors and Feed Lines De-Embedding Techniques for PCB Microwave Components S-Parameters Measurements Up To 50 Ghz
Connectors and lines de-embedding techniques for PCB microwave components S-parameters measurements up to 50 are considered. Comparison between widely used Multiline Thru-Reflect-Line (MTRL) method and promising 2xThru method are presented. This paper has demonstrated that both methods give same results, however, 2xThru method requires just one measured structure as opposite MTRL, where six measured structures are used. The difference between obtained and measured parameters of device under test are less than 0.35 dB in magnitude and 1.5° in phase for insertion loss, and less than 0.08 in magnitude and 10° in phase for return loss at most frequency points.
- 16 May 2020
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 30 (9)
A combined technique for amplifier oriented small‐signal noise model extraction
- 16 May 2020
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 30 (9)
A combined technique for amplifier oriented small‐signal noise model extraction
- Open Access
- 24 March 2020
- Published by CRI Electronics in Issues of radio electronics
- No. 2,p. 23-30
A STUDY OF TECHNOLOGY PARAMETERS INFLUENCE ON THE ELECTROPHYSICAL CHARACTERISTICS OF A MESFET USING TCAD SIMULATIONS
В статье представлены результаты исследования физико-технологической модели типового полевого транзистора с барьером Шоттки (ПТШ). Проведено моделирование пробивных характеристик ПТШ при различных параметрах подзатворного углубления. Представлено сравнение диаграмм скорости генерации горячих носителей для плоской структуры ПТШ и структуры с подзатворным углублением. Получена зависимость напряжения пробоя стока от глубины подзатворного углубления. Также в работе предложен новый подход, позволяющий установить взаимосвязь между параметрами ионной имплантации контактных областей и канала ПТШ и внутренними емкостями малосигнальной эквивалентной схемы транзистора. Данный подход основан на перспективном направлении контроля, называемом виртуальной метрологией, где параметры технологического процесса используются для предсказывания критических параметров, характеризующих его результат. Для реализации данного подхода построены предиктивные модели на основе четырех популярных методов машинного обучения: линейной регрессии, машины опорных векторов, искусственной нейронной сети и композиции решающих деревьев.
- 24 March 2020
- Published by CRI Electronics in Issues of radio electronics
- No. 2,p. 23-30
Open AccessA STUDY OF TECHNOLOGY PARAMETERS INFLUENCE ON THE ELECTROPHYSICAL CHARACTERISTICS OF A MESFET USING TCAD SIMULATIONS
В статье представлены результаты исследования физико-технологической модели типового полевого транзистора с барьером Шоттки (ПТШ). Проведено моделирование пробивных характеристик ПТШ при различных параметрах подзатворного углубления. Представлено сравнение диаграмм скорости генерации горячих носителей для плоской структуры ПТШ и структуры с подзатворным углублением. Получена зависимость напряжения пробоя стока от глубины подзатворного углубления. Также в работе предложен новый подход, позволяющий установить взаимосвязь между параметрами ионной имплантации контактных областей и канала ПТШ и внутренними емкостями малосигнальной эквивалентной схемы транзистора. Данный подход основан на перспективном направлении контроля, называемом виртуальной метрологией, где параметры технологического процесса используются для предсказывания критических параметров, характеризующих его результат. Для реализации данного подхода построены предиктивные модели на основе четырех популярных методов машинного обучения: линейной регрессии, машины опорных векторов, искусственной нейронной сети и композиции решающих деревьев.