Hossein Mosavi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hossein Mosavi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Kyle A. Riding
2 shared publications- Mohammed H. Alyami
University of Florida
2 shared publications Arnesh Das
University of Illinois at Urbana-Champaign, Urbana, IL
1 shared publication- Behzad Tahmouresi
Department of Civil Engineering, University of Guilan, Rasht, Iran
1 shared publication - Christopher C. Ferraro
Department of Civil and Coastal Engineering, The University of Florida, Engineering School of Sustainable Infrastructure and the Environment, 365 Weil Hall, P.O. Box 116580, Gainesville, FL 32611, USA
1 shared publication David A. Lange
University of Illinois at Urbana-Champaign, Urbana, IL
1 shared publication
Latest Publications
- 11 March 2021
- Published by Wiley in Structural Concrete
- Vol. 23 (4) , 2120-2131
Effect of pre‐coating lightweight aggregates on the self‐compacting concrete
The porous lightweight aggregates adversely affect fresh properties of concrete, including slump and disruption of pumping concrete. Besides, this type of concrete is very susceptible to shrinkage cracking. In this study, two types of lightweight aggregates were used with a combination of two types of coating, including hydrophobic polymers ‐polyvinyl acetate and styrene‐butadiene rubber coatings. The coatings were applied in single and double layers. For the fresh concrete, the fresh properties of concrete, including slump flow, T50, flow time, and L‐Box were evaluated and for the hardened concrete, compressive strength, flexural strength, tensile strength, water absorption and shrinkage was studied. It was seen that the slump flow of coated lightweight aggregates increased by 10%, and also coating process reduced the water absorption of the aggregates up to 82%. The compressive strength increased by up to 21% for the coated aggregates. Scanning electron microscopy was also used to investigate the microstructure of the mortar‐aggregate interface. Microstructural images showed a uniform and dense interfacial zone of cementitious matrix‐aggregate for coated lightweight aggregates. Moreover, an improvement of 50–150 μm in the interfacial zone's thickness was seen for coated aggregates compared to uncoated aggregates.
- 11 March 2021
- Published by Wiley in Structural Concrete
- Vol. 23 (4) , 2120-2131
Effect of pre‐coating lightweight aggregates on the self‐compacting concrete
The porous lightweight aggregates adversely affect fresh properties of concrete, including slump and disruption of pumping concrete. Besides, this type of concrete is very susceptible to shrinkage cracking. In this study, two types of lightweight aggregates were used with a combination of two types of coating, including hydrophobic polymers ‐polyvinyl acetate and styrene‐butadiene rubber coatings. The coatings were applied in single and double layers. For the fresh concrete, the fresh properties of concrete, including slump flow, T50, flow time, and L‐Box were evaluated and for the hardened concrete, compressive strength, flexural strength, tensile strength, water absorption and shrinkage was studied. It was seen that the slump flow of coated lightweight aggregates increased by 10%, and also coating process reduced the water absorption of the aggregates up to 82%. The compressive strength increased by up to 21% for the coated aggregates. Scanning electron microscopy was also used to investigate the microstructure of the mortar‐aggregate interface. Microstructural images showed a uniform and dense interfacial zone of cementitious matrix‐aggregate for coated lightweight aggregates. Moreover, an improvement of 50–150 μm in the interfacial zone's thickness was seen for coated aggregates compared to uncoated aggregates.
- 1 December 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 229
Potential accelerated test methods for physical sulfate attack on concrete
- 1 December 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 229
Potential accelerated test methods for physical sulfate attack on concrete
- 22 June 2019
- Published by Springer Nature in RILEM Bookseries
- p. 299-306
Use of Electrical Test Method on Determination Aging Factor of Concrete Incorporating Supplementary Cementitious Materials
- 22 June 2019
- Published by Springer Nature in RILEM Bookseries
- p. 299-306
Use of Electrical Test Method on Determination Aging Factor of Concrete Incorporating Supplementary Cementitious Materials
- Top Cited Papers
- 1 March 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 202, 266-275
Acid resistance and durability properties of steel fiber-reinforced concrete incorporating rice husk ash and recycled aggregate
- 1 March 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 202, 266-275
Top Cited PapersAcid resistance and durability properties of steel fiber-reinforced concrete incorporating rice husk ash and recycled aggregate
- 18 April 2018
- Published by ASME International
Environmental and Track Factors That Contribute to Abrasion Damage
Sites with known occurrences of mud pumping or other track concerns were investigated to determine the prevalence of concrete bottom tie abrasion and environmental and track conditions that could contribute to its occurrence. Field investigations showed that it occurs in diverse geographic locations around the U.S. and is a source of continued maintenance concern for railroads. Water appeared to be a significant factor involved in concrete bottom tie abrasion. Ballast fouling, center-binding cracking, rail surface profile variations, and large track movement during loading was seen in locations with concrete bottom tie abrasion. Bumps or track stiffness changes were often found at locations of abrasion damage. Specifically, some locations with known stiff track conditions exhibited significant abrasion damage.
- 18 April 2018
- Published by ASME International
Environmental and Track Factors That Contribute to Abrasion Damage
Sites with known occurrences of mud pumping or other track concerns were investigated to determine the prevalence of concrete bottom tie abrasion and environmental and track conditions that could contribute to its occurrence. Field investigations showed that it occurs in diverse geographic locations around the U.S. and is a source of continued maintenance concern for railroads. Water appeared to be a significant factor involved in concrete bottom tie abrasion. Ballast fouling, center-binding cracking, rail surface profile variations, and large track movement during loading was seen in locations with concrete bottom tie abrasion. Bumps or track stiffness changes were often found at locations of abrasion damage. Specifically, some locations with known stiff track conditions exhibited significant abrasion damage.
- 18 April 2018
- Published by ASME International
A Performance-Based Approach to Concrete Freeze-Thaw Durability
Concrete railroad ties can experience deterioration from freezing and thawing in cold climates typical to many railroads. Materials and manufacturing processes used to make concrete railroad ties can be controlled to give ties a long period of frost immunity. A performance-based criterion for selection of concrete materials and durability requirements would allow plants more flexibility in material selection and improve overall performance in the field. A new performance-based approach is described to concrete freeze-thaw quality control. In order to accommodate implementation, work was performed at a precast concrete railroad tie manufacturing plant to compare currently used concrete freeze-thaw quality control methods to the proposed performance-based method. This comparison is described to illustrate the benefits of this new performance-based approach.
- 18 April 2018
- Published by ASME International
A Performance-Based Approach to Concrete Freeze-Thaw Durability
Concrete railroad ties can experience deterioration from freezing and thawing in cold climates typical to many railroads. Materials and manufacturing processes used to make concrete railroad ties can be controlled to give ties a long period of frost immunity. A performance-based criterion for selection of concrete materials and durability requirements would allow plants more flexibility in material selection and improve overall performance in the field. A new performance-based approach is described to concrete freeze-thaw quality control. In order to accommodate implementation, work was performed at a precast concrete railroad tie manufacturing plant to compare currently used concrete freeze-thaw quality control methods to the proposed performance-based method. This comparison is described to illustrate the benefits of this new performance-based approach.