Pisipaty Srinivas Kishore
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pisipaty Srinivas Kishore has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
A. Brusly Solomon
Centre for Research in Material Science and Thermal Management, Department of Mechanical Engineering, Karunya Institute of Technology and Sciences, Coimbatore, India
2 shared publicationsDharma Rao Vedula
Department of Mechanical Engineering, Gayatri Vidya Parishad College of Engineering (Autonomous), Visakhapatnam, India
2 shared publicationsN. S. Naveen
2 shared publicationsSireesha Veeramachaneni
College of Engineering (A), Andhra University & Department of Mechanical Engineering, Gayatri Vidya Parishad College of Engineering (Autonomous), Visakhapatnam, India
2 shared publicationsAkula Naresh Kumar
Department of Mechanical Engineering, Lakireddy Bali Reddy College of Engineering, Mylavaram, AP, India
1 shared publication- Bragadeshwaran Ashok
Department of Automotive Engineering, School of Mechanical Engineering, Vellore Institute of Technology, Vellore 632014, Tamil Nadu, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 10 (5) , 1184-1197
Optimizing the thermal performance of a double-pipe heat exchanger using twisted tapes with variable cuts and Fe3O4 nanofluid
This research work aims to optimize double pipe heat exchanger performance using Taguchi, ANOVA, and ANN. Experimental trials involved varying ferric oxide nanoparticles, cut radius, and volume-based flow rate. Twisted tapes with ratios of 3, 5, and 7 were placed within the tube. Assessed heat transfer characteristics included h, Nu, ff, and thermal performance factor. Taguchi, ANOVA, and ANN optimization techniques were applied to the experimental data. A Taguchi optimization using an L9 orthogonal array focused on input attributes (Vol % of nanoparticles, flow rate, radius of cut), with output attributes being heat transfer co-efficient (h), Nusselt number (Nu), friction factor(ff) and thermal performance factor. Results revealed a notable flow rate effect on enhancing h, Nu, and ff, while the addition of nanoparticles significantly influenced thermal performance. Taguchi and ANOVA were conducted using MINI Tab and ANN was implemented through MATLAB. Test data demonstrated that nanoparticle dispersants in nanofluid significantly improved heat transfer properties, consistent with the noteworthy improvement indicated by optimization techniques. The convective heat transfer coefficient parameter showed improvement with a coolant flow rate of 50.29% and a volume of nanoparticles at 27.32%. The enhancement of Nusselt number (Nu) was influenced by a coolant flow rate of 50.34% and a volume percent of nanoparticles at 34.25%. The thermal performance factor was significantly influenced by the volume percent of nanoparticles (79.75%) and the radius of cut (3.83%).The experimental data aligned well with findings from Taguchi and ANN.
- 1 January 2024
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 10 (5) , 1184-1197
Open AccessOptimizing the thermal performance of a double-pipe heat exchanger using twisted tapes with variable cuts and Fe3O4 nanofluid
This research work aims to optimize double pipe heat exchanger performance using Taguchi, ANOVA, and ANN. Experimental trials involved varying ferric oxide nanoparticles, cut radius, and volume-based flow rate. Twisted tapes with ratios of 3, 5, and 7 were placed within the tube. Assessed heat transfer characteristics included h, Nu, ff, and thermal performance factor. Taguchi, ANOVA, and ANN optimization techniques were applied to the experimental data. A Taguchi optimization using an L9 orthogonal array focused on input attributes (Vol % of nanoparticles, flow rate, radius of cut), with output attributes being heat transfer co-efficient (h), Nusselt number (Nu), friction factor(ff) and thermal performance factor. Results revealed a notable flow rate effect on enhancing h, Nu, and ff, while the addition of nanoparticles significantly influenced thermal performance. Taguchi and ANOVA were conducted using MINI Tab and ANN was implemented through MATLAB. Test data demonstrated that nanoparticle dispersants in nanofluid significantly improved heat transfer properties, consistent with the noteworthy improvement indicated by optimization techniques. The convective heat transfer coefficient parameter showed improvement with a coolant flow rate of 50.29% and a volume of nanoparticles at 27.32%. The enhancement of Nusselt number (Nu) was influenced by a coolant flow rate of 50.34% and a volume percent of nanoparticles at 34.25%. The thermal performance factor was significantly influenced by the volume percent of nanoparticles (79.75%) and the radius of cut (3.83%).The experimental data aligned well with findings from Taguchi and ANN.
- 26 June 2021
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 147 (10) , 5985-5999
Effect of copper–graphene hybrid nanoplatelets in a miniature loop heat pipe
- 26 June 2021
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 147 (10) , 5985-5999
Effect of copper–graphene hybrid nanoplatelets in a miniature loop heat pipe
- 5 November 2020
- Published by Taylor & Francis in Journal of Dispersion Science and Technology
- Vol. 43 (3) , 1-13
Experimental investigation on heat transfer parameters of an automotive car radiator using graphene/water-ethylene glycol coolant
In the present study, forced convective heat transfer of a Water-EG coolant has been compared with Water-EG based nanocoolant in a radiator. Conventional coolant Water-EG was considered in the ratio of 70:30 as a base fluid, for that different proportions of 0.1, 0.2 and 0.3 Vol% has been prepared by the addition of graphene nanoparticles. Graphene nanofluid was synthesized by two-step method. Experimental studies were conducted in a radiator by altering the flow rates and inlet temperature of the coolant in the ranges of 2, 4, 6 and 8 L/min and 50, 60 and 70 °C. Heat transfer parameters like Heat transfer rate, Convective heat transfer co-efficient, Nusselt number, Reynolds number and friction factor are evaluated experimentally. Graphical Abstract
- 5 November 2020
- Published by Taylor & Francis in Journal of Dispersion Science and Technology
- Vol. 43 (3) , 1-13
Experimental investigation on heat transfer parameters of an automotive car radiator using graphene/water-ethylene glycol coolant
In the present study, forced convective heat transfer of a Water-EG coolant has been compared with Water-EG based nanocoolant in a radiator. Conventional coolant Water-EG was considered in the ratio of 70:30 as a base fluid, for that different proportions of 0.1, 0.2 and 0.3 Vol% has been prepared by the addition of graphene nanoparticles. Graphene nanofluid was synthesized by two-step method. Experimental studies were conducted in a radiator by altering the flow rates and inlet temperature of the coolant in the ranges of 2, 4, 6 and 8 L/min and 50, 60 and 70 °C. Heat transfer parameters like Heat transfer rate, Convective heat transfer co-efficient, Nusselt number, Reynolds number and friction factor are evaluated experimentally. Graphical Abstract
- 2 August 2020
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 34 (7) , 639-661
Characterization of flat miniature loop heat pipe using water and methanol at different inclinations
Experiments have been conducted on a flat rectangular loop heat pipe with water and methanol at heat loads from 40 to 320 W at three orientations of the heat pipe (0°, 45°, 90°) and two filling ratios (33% and 50%). Performance parameters such as thermal resistance, effective thermal conductivity and capillary limit are calculated from the experimental data. The results exhibited that the thermal performance of water is better than methanol with least thermal resistance 0.13 K/W, maximum capillary limit 2626.72 W and an effective thermal conductivity 84490.48 W/mK at a heat load 320 W in horizontal position for 33% filling ratio.
- 2 August 2020
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 34 (7) , 639-661
Characterization of flat miniature loop heat pipe using water and methanol at different inclinations
Experiments have been conducted on a flat rectangular loop heat pipe with water and methanol at heat loads from 40 to 320 W at three orientations of the heat pipe (0°, 45°, 90°) and two filling ratios (33% and 50%). Performance parameters such as thermal resistance, effective thermal conductivity and capillary limit are calculated from the experimental data. The results exhibited that the thermal performance of water is better than methanol with least thermal resistance 0.13 K/W, maximum capillary limit 2626.72 W and an effective thermal conductivity 84490.48 W/mK at a heat load 320 W in horizontal position for 33% filling ratio.
- 10 January 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (7) , 6652-6676
Engine parameter optimization of palm oil biodiesel as alternate fuel in CI engine
Stringent emission regulations and depletion of crude oil are driving researchers toward alternative fuels. In this context, palm oil emerges as a good competitor as it is highly economical compared to other alternative fuels. The current research work centers around the impact of palm oil methyl ester on performance, combustion, and emission characteristics at varying injection timings and exhaust gas recirculation rates. In the first phase of this research work, various blends of palm oil methyl ester with diesel with volume concentrations of 10, 20, and 30% were prepared and tested at different load conditions. Injection timing was then varied for the optimized blend. In the second phase, the impact of exhaust gas blending with fresh charge was studied at optimized injection timing. The test outcomes revealed that 20% mix of palm oil at 27° bTDC with exhaust gas blending of 20% generated higher brake thermal efficiency, higher peak pressure, and less hydrocarbon and nitrogen oxide emissions compared to diesel at standard injection timing of 23° bTDC and no blending of exhaust gases with fresh charge. However, progression of injection timing with 20% exhaust gas mixing indicated a slight penalty in smoke discharges. Brake thermal efficiency at advanced injection timing with 20% mix of exhaust gases reduced by 7.7% for diesel and increased by 6.5% for 20% blend of palm oil when compared to standard injection timing of diesel and no blending of exhaust gases. Significant diminishments in oxides of nitrogen (lessened by 6.6%) and hydrocarbons (decreased by 30.43%) have been noted for 20% mix of biodiesel at advanced injection timing with 20% exhaust gas mix contrasted to diesel at standard conditions. Therefore, the present examination prescribes 20% merging of exhaust gases for 20% blend of palm oil with advancement of injection timing for diesel engine applications.
- 10 January 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (7) , 6652-6676
Engine parameter optimization of palm oil biodiesel as alternate fuel in CI engine
Stringent emission regulations and depletion of crude oil are driving researchers toward alternative fuels. In this context, palm oil emerges as a good competitor as it is highly economical compared to other alternative fuels. The current research work centers around the impact of palm oil methyl ester on performance, combustion, and emission characteristics at varying injection timings and exhaust gas recirculation rates. In the first phase of this research work, various blends of palm oil methyl ester with diesel with volume concentrations of 10, 20, and 30% were prepared and tested at different load conditions. Injection timing was then varied for the optimized blend. In the second phase, the impact of exhaust gas blending with fresh charge was studied at optimized injection timing. The test outcomes revealed that 20% mix of palm oil at 27° bTDC with exhaust gas blending of 20% generated higher brake thermal efficiency, higher peak pressure, and less hydrocarbon and nitrogen oxide emissions compared to diesel at standard injection timing of 23° bTDC and no blending of exhaust gases with fresh charge. However, progression of injection timing with 20% exhaust gas mixing indicated a slight penalty in smoke discharges. Brake thermal efficiency at advanced injection timing with 20% mix of exhaust gases reduced by 7.7% for diesel and increased by 6.5% for 20% blend of palm oil when compared to standard injection timing of diesel and no blending of exhaust gases. Significant diminishments in oxides of nitrogen (lessened by 6.6%) and hydrocarbons (decreased by 30.43%) have been noted for 20% mix of biodiesel at advanced injection timing with 20% exhaust gas mix contrasted to diesel at standard conditions. Therefore, the present examination prescribes 20% merging of exhaust gases for 20% blend of palm oil with advancement of injection timing for diesel engine applications.