Denis Andreevich Zemtsov
Research Subjects
Denis Andreevich Zemtsov has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandr Sergeyevich Frolov
Reshetnev Siberian State University of Science and Technology, Krasnoyarsk, Russia
4 shared publications - Anastasiya V. Bogatkova
Institute of Chemical Technology, Reshetnev Siberian State University of Science and Technology, 31 Krasnoyarsky Rabochy Av., Krasnoyarsk 660037, Russia
3 shared publications - Nikolai A. Voinov
Reshetnev Siberian State University of Science and Technology, Krasnoyarsk, Russia
3 shared publications Nikolay Aleksandrovich Voynov
Сибирский государственный университет науки и технологий имени академика М.Ф. Решетнёва
3 shared publications- Ol'Ga Petrovna Zhukova
Сибирский государственный университет науки и технологий имени академика М.Ф. Решетнёва
3 shared publications Anastasia Viktorovna Bogatkova
Сибирский государственный университет науки и технологий имени академика М.Ф. Решетнёва
2 shared publications
Latest Publications
- Open Access
- 4 December 2024
- Published by Altai State University in Chemistry of plant raw material
- No. 4,p. 405-415
CROSS-CURRENT PACKED TRAY FOR A DIABATIC PRODUCT-CONCENTRATING COLUMN
Diabatic rectification is one of the ways to increase the energy efficiency of the mixed distillation process. Diabatic units in which partial condensation of rising vapours and further evaporation of the condensate on contact devices placed on trays have proved effective. Horizontal perforated plate units are promising in this respect. They have low resistance and high efficiency, but have a narrow operating range. To intensify the separation process and increase column productivity, a combined cross-flow packed tray was developed and investigated. It consists of a spiral-prismatic packing placed in coaxial perforated cups and profiled plates, allowing the slurry to flow continuously downwards and preventing condensate from entering the evaporation zone. This type of tray design has made it possible to intensify the process of heat and mass transfer in the vapour and liquid phases and to extend the operating range of the tray. The results of the experimental study of the developed tray in a pilot rectification column are presented. The distribution of the concentration of ethanol in the liquid flowing down the plates is shown. The effective temperature difference for mist evaporation on the profiled plates and condensation under the plates is determined. The value of the heat transfer coefficient of the heat flow on the plate is determined. Comparison of characteristic parameters of adiabatic column with spiral-prismatic packed countercurrent type with a diabatic column with cross-flow trays is made and the advantage of the latter is shown. For the construction of low tonnage product concentrating columns, also under vacuum, the developed trays are recommended.
- 4 December 2024
- Published by Altai State University in Chemistry of plant raw material
- No. 4,p. 405-415
Open AccessCROSS-CURRENT PACKED TRAY FOR A DIABATIC PRODUCT-CONCENTRATING COLUMN
Diabatic rectification is one of the ways to increase the energy efficiency of the mixed distillation process. Diabatic units in which partial condensation of rising vapours and further evaporation of the condensate on contact devices placed on trays have proved effective. Horizontal perforated plate units are promising in this respect. They have low resistance and high efficiency, but have a narrow operating range. To intensify the separation process and increase column productivity, a combined cross-flow packed tray was developed and investigated. It consists of a spiral-prismatic packing placed in coaxial perforated cups and profiled plates, allowing the slurry to flow continuously downwards and preventing condensate from entering the evaporation zone. This type of tray design has made it possible to intensify the process of heat and mass transfer in the vapour and liquid phases and to extend the operating range of the tray. The results of the experimental study of the developed tray in a pilot rectification column are presented. The distribution of the concentration of ethanol in the liquid flowing down the plates is shown. The effective temperature difference for mist evaporation on the profiled plates and condensation under the plates is determined. The value of the heat transfer coefficient of the heat flow on the plate is determined. Comparison of characteristic parameters of adiabatic column with spiral-prismatic packed countercurrent type with a diabatic column with cross-flow trays is made and the advantage of the latter is shown. For the construction of low tonnage product concentrating columns, also under vacuum, the developed trays are recommended.
- Open Access
- 12 March 2024
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 362-371
MASS TRANSFER IN THE BIOREACTOR DURING GAS DISPERSION FROM THE STIRRER VORTEX CAVITY
Химия растительного сырья Научные журналы Алтайского государственного университета Научные журналы АлтГУ
- 12 March 2024
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 362-371
Open AccessMASS TRANSFER IN THE BIOREACTOR DURING GAS DISPERSION FROM THE STIRRER VORTEX CAVITY
Химия растительного сырья Научные журналы Алтайского государственного университета Научные журналы АлтГУ
- Open Access
- 4 April 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (2) , 30
Method for Intensive Gas–Liquid Dispersion in a Stirred Tank
This article presents the results of hydrodynamics and mass exchange in a stirred tank upon the introduction of gas from an open gas vortex cavity into local liquid regions with reduced pressure. It establishes conditions for the intensive dispersion of gas. Velocity fields and liquid pressure behind the stirrer paddles are determined by numerical simulation in OpenFOAM. The gas content value, gas bubble diameters, and phase surface are determined experimentally. The stirrer power criterion is calculated by taking into account the gas content and power input. The experimental mass transfer data based on the absorption of atmospheric oxygen into water during the dispersion of gas from the open vortex cavity in the local liquid regions behind the rotating stirrer paddles are presented. In this case, the energy dissipation from the rotating stirrer reaches 25 W/kg, with a phase surface of 1000 m−1 and a surface mass transfer coefficient of up to 0.3·10−3 m/s. These parameters are obviously higher than the data obtained in the apparatus for mass exchange through surface vorticity. The advantage of the given method for gas dispersion in a liquid is the functional stability of the apparatus regardless of how deep the stirrer is immersed in the liquid or the temperature or pressure of the gas. Apparatuses based on the intensive gas dispersion method allow for varying the mass transfer coefficient and gas content across a broad range of values. This allows establishing a dependency between the experimentally obtained mass transfer coefficient, energy dissipation, and phase surface values. An equation for calculating the mass transfer coefficient is formulated by taking into account the geometric parameters of the stirrer apparatus based on the stirring power and phase surface values.
- 4 April 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (2) , 30
Open AccessMethod for Intensive Gas–Liquid Dispersion in a Stirred Tank
This article presents the results of hydrodynamics and mass exchange in a stirred tank upon the introduction of gas from an open gas vortex cavity into local liquid regions with reduced pressure. It establishes conditions for the intensive dispersion of gas. Velocity fields and liquid pressure behind the stirrer paddles are determined by numerical simulation in OpenFOAM. The gas content value, gas bubble diameters, and phase surface are determined experimentally. The stirrer power criterion is calculated by taking into account the gas content and power input. The experimental mass transfer data based on the absorption of atmospheric oxygen into water during the dispersion of gas from the open vortex cavity in the local liquid regions behind the rotating stirrer paddles are presented. In this case, the energy dissipation from the rotating stirrer reaches 25 W/kg, with a phase surface of 1000 m−1 and a surface mass transfer coefficient of up to 0.3·10−3 m/s. These parameters are obviously higher than the data obtained in the apparatus for mass exchange through surface vorticity. The advantage of the given method for gas dispersion in a liquid is the functional stability of the apparatus regardless of how deep the stirrer is immersed in the liquid or the temperature or pressure of the gas. Apparatuses based on the intensive gas dispersion method allow for varying the mass transfer coefficient and gas content across a broad range of values. This allows establishing a dependency between the experimentally obtained mass transfer coefficient, energy dissipation, and phase surface values. An equation for calculating the mass transfer coefficient is formulated by taking into account the geometric parameters of the stirrer apparatus based on the stirring power and phase surface values.
- Open Access
- 27 June 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (4) , 48
Experimental Study and Numerical Simulation of Hydrodynamic Parameters of Tangential Swirlers
This paper presents and patents new profiled- and annular-channel tangential swirlers with 1.8–3 times less hydraulic drag coefficient compared to swirlers with straight channel walls at the same flow rate, respectively. The results of numerical simulation of the gas velocity and pressure profiles for tangential swirler channels of different structures are presented. The modelling was carried out with the help of OpenFOAM software using the k-ε turbulence model. It is found that the shape of the velocity profile at the channel inlet has a decisive influence on the swirler drag coefficient. The greatest contribution to the total drag coefficient of the tangential swirler is made by the pressure drop at the channel inlet compared to the pressure drop at the channel wall and the channel outlet. The experimental dependencies of the tangential swirlers’ drag coefficient on the Reynolds number with a gas criterion of 2000–20,000 and the following structural channel parameters: width 1, 2–9 mm, height 1, 5–10 mm, number 5–45 units, inclination angle 0–45° are presented. The experimental data were compared with the modelling calculations and the convergence of data was achieved. The generalized dependence for the measurement of the hydraulic drag coefficient of three types of tangential swirlers considering the effect made by the geometric parameters (flow rate, width and height of the channel, wall inclination angle) on the pressure drop has been determined; it can be useful at the unit design stage as it allows for reducing the calculation time of the swirler parameters.
- 27 June 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (4) , 48
Open AccessExperimental Study and Numerical Simulation of Hydrodynamic Parameters of Tangential Swirlers
This paper presents and patents new profiled- and annular-channel tangential swirlers with 1.8–3 times less hydraulic drag coefficient compared to swirlers with straight channel walls at the same flow rate, respectively. The results of numerical simulation of the gas velocity and pressure profiles for tangential swirler channels of different structures are presented. The modelling was carried out with the help of OpenFOAM software using the k-ε turbulence model. It is found that the shape of the velocity profile at the channel inlet has a decisive influence on the swirler drag coefficient. The greatest contribution to the total drag coefficient of the tangential swirler is made by the pressure drop at the channel inlet compared to the pressure drop at the channel wall and the channel outlet. The experimental dependencies of the tangential swirlers’ drag coefficient on the Reynolds number with a gas criterion of 2000–20,000 and the following structural channel parameters: width 1, 2–9 mm, height 1, 5–10 mm, number 5–45 units, inclination angle 0–45° are presented. The experimental data were compared with the modelling calculations and the convergence of data was achieved. The generalized dependence for the measurement of the hydraulic drag coefficient of three types of tangential swirlers considering the effect made by the geometric parameters (flow rate, width and height of the channel, wall inclination angle) on the pressure drop has been determined; it can be useful at the unit design stage as it allows for reducing the calculation time of the swirler parameters.
- 3 May 2022
- Published by BioResources in BioResources
- Vol. 17 (3) , 3883-3905
Sedimentation of refined cellulosic pulp fines in the suspension during physical agglomeration
A physical coagulator of fines was employed to separate suspensions comprising refined sulphate cellulose and waste paper, where no reagents were required. The physical coagulator was a porous cylinder with a rotating disk placed in its cavity. Using the MorFi Neo fibre analyser and the Hitachi SU 3500 digital microscope, a dispersed size distribution of well-developed fines in a suspension derived from softwood and hardwood pulp was obtained. The kinetics of fine sedimentation in the suspension was studied. The sedimentation rate of both individual agglomerates and a mass of them, as well as the magnitude of mass concentration in a cleared liquid, was determined. A relationship between the concentration of fines in the suspension and the structure of the pulp during their sedimentation was established. To intensify the fines sedimentation process, it was proposed to return a part of the sediment to the suspension passing into the physical coagulator. Process parameters for the sedimentation process and the construction of the sedimentation tank were obtained. The unit designed for collecting fines from the suspension is shown schematically. Use of this unit reduced the fibre sedimentation time, decreased the loads in wastewaters, and retained the consumer value of the pulp fibres.
- 3 May 2022
- Published by BioResources in BioResources
- Vol. 17 (3) , 3883-3905
Sedimentation of refined cellulosic pulp fines in the suspension during physical agglomeration
A physical coagulator of fines was employed to separate suspensions comprising refined sulphate cellulose and waste paper, where no reagents were required. The physical coagulator was a porous cylinder with a rotating disk placed in its cavity. Using the MorFi Neo fibre analyser and the Hitachi SU 3500 digital microscope, a dispersed size distribution of well-developed fines in a suspension derived from softwood and hardwood pulp was obtained. The kinetics of fine sedimentation in the suspension was studied. The sedimentation rate of both individual agglomerates and a mass of them, as well as the magnitude of mass concentration in a cleared liquid, was determined. A relationship between the concentration of fines in the suspension and the structure of the pulp during their sedimentation was established. To intensify the fines sedimentation process, it was proposed to return a part of the sediment to the suspension passing into the physical coagulator. Process parameters for the sedimentation process and the construction of the sedimentation tank were obtained. The unit designed for collecting fines from the suspension is shown schematically. Use of this unit reduced the fibre sedimentation time, decreased the loads in wastewaters, and retained the consumer value of the pulp fibres.
- Open Access
- 12 April 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (2) , 29
Intensification of Heat and Mass Transfer in a Diabatic Column with Vortex Trays
We used vortex contact devices that we developed and investigated to make a new design of an alcohol diabatic distillation column with heat exchange pipes (as the reflux condenser) passing through concentrating section trays. In the column, ascending vapors partially condensed on the surface of vertically installed heat exchange tubes, forming a reflux. The reflux was then mixed with the draining liquid flow in the vortex contact devices placed on the trays. Heat was removed from the column through the boiling of the draining water film along the inner surface of the heat exchange pipes. We compared both diabatic and adiabatic columns fitted with the developed vortex contact devices on the trays. The proposed innovative contact system allows increasing productivity, reducing column dimensions and steam- and heat-transfer medium consumption, and increasing separation efficiency. Dependences for calculating the gas content, hydraulic resistance, and interphase surface required for designing the vortex contact devices of the proposed unit trays are presented.
- 12 April 2022
- Published by MDPI AG in Chemengineering
- Vol. 6 (2) , 29
Open AccessIntensification of Heat and Mass Transfer in a Diabatic Column with Vortex Trays
We used vortex contact devices that we developed and investigated to make a new design of an alcohol diabatic distillation column with heat exchange pipes (as the reflux condenser) passing through concentrating section trays. In the column, ascending vapors partially condensed on the surface of vertically installed heat exchange tubes, forming a reflux. The reflux was then mixed with the draining liquid flow in the vortex contact devices placed on the trays. Heat was removed from the column through the boiling of the draining water film along the inner surface of the heat exchange pipes. We compared both diabatic and adiabatic columns fitted with the developed vortex contact devices on the trays. The proposed innovative contact system allows increasing productivity, reducing column dimensions and steam- and heat-transfer medium consumption, and increasing separation efficiency. Dependences for calculating the gas content, hydraulic resistance, and interphase surface required for designing the vortex contact devices of the proposed unit trays are presented.
- Open Access
- 10 March 2022
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 335-342
RESISTANCE OF TANGENTIAL SWIRLERS WITH ANNULAR CHANNELS
A review of vortex apparatuses and processes in which a rotating gas-liquid flow is used as an intensification of heat and mass transfer is presented. It is shown that tangential swirlers, which are easy to manufacture and compact, have found the greatest application in industrial practice for creating gas (steam) rotation. It is experimentally established that tangential swirlers with annular walls of channels intended for gas passage have the lowest hydraulic resistance. The data on the hydraulic resistance of tangential swirlers with annular channels, velocity and pressure obtained experimentally and by calculation in a wide range of variation of the design parameters of the device are presented. The dependences between the hydraulic resistance of the swirler and its design parameters are revealed. Numerical simulation of the parameters of the gas flow in the channels is carried out. Diagrams of the pressure and velocity distribution are presented and analyzed, and experimental data on the influence of the design parameters of the swirler channel, such as width and length, on its hydraulic resistance are confirmed. An empirical dependence for determining the hydraulic resistance coefficient of a tangential swirler with annular channels is presented for engineering calculations.
- 10 March 2022
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 335-342
Open AccessRESISTANCE OF TANGENTIAL SWIRLERS WITH ANNULAR CHANNELS
A review of vortex apparatuses and processes in which a rotating gas-liquid flow is used as an intensification of heat and mass transfer is presented. It is shown that tangential swirlers, which are easy to manufacture and compact, have found the greatest application in industrial practice for creating gas (steam) rotation. It is experimentally established that tangential swirlers with annular walls of channels intended for gas passage have the lowest hydraulic resistance. The data on the hydraulic resistance of tangential swirlers with annular channels, velocity and pressure obtained experimentally and by calculation in a wide range of variation of the design parameters of the device are presented. The dependences between the hydraulic resistance of the swirler and its design parameters are revealed. Numerical simulation of the parameters of the gas flow in the channels is carried out. Diagrams of the pressure and velocity distribution are presented and analyzed, and experimental data on the influence of the design parameters of the swirler channel, such as width and length, on its hydraulic resistance are confirmed. An empirical dependence for determining the hydraulic resistance coefficient of a tangential swirler with annular channels is presented for engineering calculations.
- Open Access
- 5 March 2020
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 347-354
SWIRL STAGES FOR HEAT AND MASS EXCHANGE EQUIPMENT
Представлены результаты экспериментальных исследований гидродинамики и массообмена на вихревых ступенях в режиме барботажа, а также данные численного моделирования методом конечных элементов с использованием моделей k-ε турбулентности и пузырькового течения. Это позволило установить наличие циркуляционного движения жидкости на ступени, определить профили скоростей фаз, получить величину начальной скорости движения газовой фазы, при которой наблюдается согласование экспериментальных и расчетных значений скорости жидкости. Расчетным путем показано влияние цилиндрической перегородки, установленной между завихрителем и стенкой ступени на профиль скорости жидкости и ее распределение в рабочем объеме. Предложено использовать полученные результаты численного моделирования при конструировании многоэлементных ступеней для обеспечения на ней требуемой гидродинамики. Исследованы новые вихревые контактные устройства с кольцевыми каналами, обладающие меньшим гидравлическим сопротивлением в сравнении с тангенциальными устройствами и обеспечивающие развитую межфазную поверхность, стабильную, без флуктуаций, работу ступени при высоких расходах газа и жидкости. Представлены данные для определения гидравлического сопротивления вихревой ступени, величины межфазной поверхности, коэффициентов массоотдачи и эффективности в исследуемом диапазоне нагрузок жидкости и газа L/G = 10–150. Разработаны конструкции вихревых контактных ступеней для промышленной бражной колонны. Контактные устройства с кольцевыми каналами позволяют довести диссипацию энергии в газовой фазе в барботажно-кольцевом режиме до 5 Вт/кг, увеличить межфазную поверхность до 2000 м-1 и достигнуть величины поверхностного коэффициента массотдачи порядка (0.5–0.8)×10-3 м/с.
- 5 March 2020
- Published by Altai State University in Chemistry of plant raw material
- No. 1,p. 347-354
Open AccessSWIRL STAGES FOR HEAT AND MASS EXCHANGE EQUIPMENT
Представлены результаты экспериментальных исследований гидродинамики и массообмена на вихревых ступенях в режиме барботажа, а также данные численного моделирования методом конечных элементов с использованием моделей k-ε турбулентности и пузырькового течения. Это позволило установить наличие циркуляционного движения жидкости на ступени, определить профили скоростей фаз, получить величину начальной скорости движения газовой фазы, при которой наблюдается согласование экспериментальных и расчетных значений скорости жидкости. Расчетным путем показано влияние цилиндрической перегородки, установленной между завихрителем и стенкой ступени на профиль скорости жидкости и ее распределение в рабочем объеме. Предложено использовать полученные результаты численного моделирования при конструировании многоэлементных ступеней для обеспечения на ней требуемой гидродинамики. Исследованы новые вихревые контактные устройства с кольцевыми каналами, обладающие меньшим гидравлическим сопротивлением в сравнении с тангенциальными устройствами и обеспечивающие развитую межфазную поверхность, стабильную, без флуктуаций, работу ступени при высоких расходах газа и жидкости. Представлены данные для определения гидравлического сопротивления вихревой ступени, величины межфазной поверхности, коэффициентов массоотдачи и эффективности в исследуемом диапазоне нагрузок жидкости и газа L/G = 10–150. Разработаны конструкции вихревых контактных ступеней для промышленной бражной колонны. Контактные устройства с кольцевыми каналами позволяют довести диссипацию энергии в газовой фазе в барботажно-кольцевом режиме до 5 Вт/кг, увеличить межфазную поверхность до 2000 м-1 и достигнуть величины поверхностного коэффициента массотдачи порядка (0.5–0.8)×10-3 м/с.
- 30 June 2018
- Published by PNRPU Publishing House in PNRPU Bulletin. Chemical Technology and Biotechnology
- No. 2,p. 146-156
Study of thermal rectification at the vortex stage
- 30 June 2018
- Published by PNRPU Publishing House in PNRPU Bulletin. Chemical Technology and Biotechnology
- No. 2,p. 146-156
Study of thermal rectification at the vortex stage
- Open Access
- 1 January 2016
- Published by Altai State University in Chemistry of plant raw material
- No. 2,p. 117-122
КОЛОННА С НИЗКИМ СОПРОТИВЛЕНИЕМ НА ОСНОВЕ ЭФФЕКТОВ ТЕРМИЧЕСКОЙ РЕКТИФИКАЦИИ
Целью исследования явилось использование термических эффектов при ректификации многокомпонентных смесей из растительного сырья. В задачи исследования входило создание ректификационной колонны с низким гидравлическим сопротивлением и высокой разделяющей способностью ступеней на основе целенаправленного воздействия на процесс термическими эффектами, вызванными испарением и конденсацией. Представлены результаты исследования процесса термической ректификации, полученные при укреплении смеси этанол – вода в колонне с 25 контактными ступенями, выполненными из горизонтально установленных пластин. Установлено что эффективность разделения смеси на нижних ступенях исследуемой колонны при термической ректификации осуществляется преимущественно за счет эффекта, вызванного парциальной конденсацией, а на верхних ступенях – за счет испарения жидкости, размещенной на поверхности пластин. Достигнуто низкое сопротивление колонны, не превышающее 40 Па, при сравнительно высокой эффективности разделения 0,4–0,7. Установлены параметры процесса, интенсифицирующие тепломассоперенос при термической ректификации. Разработанную колонну вследствие ее высокой эффективности и низкого гидравлического сопротивления рекомендуется применять для проведения процессов ректификации под вакуумом, например для обезвоживания этанола.
- 1 January 2016
- Published by Altai State University in Chemistry of plant raw material
- No. 2,p. 117-122
Open AccessКОЛОННА С НИЗКИМ СОПРОТИВЛЕНИЕМ НА ОСНОВЕ ЭФФЕКТОВ ТЕРМИЧЕСКОЙ РЕКТИФИКАЦИИ
Целью исследования явилось использование термических эффектов при ректификации многокомпонентных смесей из растительного сырья. В задачи исследования входило создание ректификационной колонны с низким гидравлическим сопротивлением и высокой разделяющей способностью ступеней на основе целенаправленного воздействия на процесс термическими эффектами, вызванными испарением и конденсацией. Представлены результаты исследования процесса термической ректификации, полученные при укреплении смеси этанол – вода в колонне с 25 контактными ступенями, выполненными из горизонтально установленных пластин. Установлено что эффективность разделения смеси на нижних ступенях исследуемой колонны при термической ректификации осуществляется преимущественно за счет эффекта, вызванного парциальной конденсацией, а на верхних ступенях – за счет испарения жидкости, размещенной на поверхности пластин. Достигнуто низкое сопротивление колонны, не превышающее 40 Па, при сравнительно высокой эффективности разделения 0,4–0,7. Установлены параметры процесса, интенсифицирующие тепломассоперенос при термической ректификации. Разработанную колонну вследствие ее высокой эффективности и низкого гидравлического сопротивления рекомендуется применять для проведения процессов ректификации под вакуумом, например для обезвоживания этанола.