Zhen Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhen Wang has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Avner Vengosh
Duke University
4 shared publications - Andrew J. Frierdich
Monash University
2 shared publications - Annah Moyo
University of Alberta
2 shared publications Arif Hussain
University of Alberta
2 shared publicationsDan Su
Heriot-Watt University
2 shared publications- Gordon D. Z. Williams
Nicholas School of the Environment, Duke University, Durham, NC 27708, USA
2 shared publications
Latest Publications
- Open Access
- 2 October 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 60 (40) , 29103-29112
Acid Leaching for Carbon Sequestration with Prospects for Critical Metal Recovery
Reducing carbon emissions and supplying critical metals for the green energy transition are essential to limiting global warming to below 1.5 °C. Here, we propose heap leaching ultramafic material with sulfuric acid followed by sequential precipitation for nickel recovery and carbon sequestration. Ultramafic materials were subjected to benchtop-scale acid leaches using 0.08–0.8 M H2SO4. The leachates were combined with NaOH to precipitate Ni (oxy)hydroxide minerals and then with NaOH + Na2CO3 to precipitate Mg carbonate minerals. The carbon sequestration potential of each sample and the efficiency of each experimental stage were calculated to estimate carbon sequestration using these techniques. The acid leaching released 2–57% of the Mg2+ along with 6–64% of the Ni2+ into the leachate, depending on acid strength and tailings mineralogy, while carbonation precipitated up to 95% of the dissolved Mg2+ and 90% of the CO32– + HCO3– in solution, depending on initial Mg2+ concentrations. Techno-economic analysis demonstrates that treatment cost and Ni production are the most important factors determining the profitability of the process, with CO2 removal being less important due to the relatively low value of carbon credits compared to Ni, but still contributing to the sustainability of this process.
- 2 October 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 60 (40) , 29103-29112
Open AccessAcid Leaching for Carbon Sequestration with Prospects for Critical Metal Recovery
Reducing carbon emissions and supplying critical metals for the green energy transition are essential to limiting global warming to below 1.5 °C. Here, we propose heap leaching ultramafic material with sulfuric acid followed by sequential precipitation for nickel recovery and carbon sequestration. Ultramafic materials were subjected to benchtop-scale acid leaches using 0.08–0.8 M H2SO4. The leachates were combined with NaOH to precipitate Ni (oxy)hydroxide minerals and then with NaOH + Na2CO3 to precipitate Mg carbonate minerals. The carbon sequestration potential of each sample and the efficiency of each experimental stage were calculated to estimate carbon sequestration using these techniques. The acid leaching released 2–57% of the Mg2+ along with 6–64% of the Ni2+ into the leachate, depending on acid strength and tailings mineralogy, while carbonation precipitated up to 95% of the dissolved Mg2+ and 90% of the CO32– + HCO3– in solution, depending on initial Mg2+ concentrations. Techno-economic analysis demonstrates that treatment cost and Ni production are the most important factors determining the profitability of the process, with CO2 removal being less important due to the relatively low value of carbon credits compared to Ni, but still contributing to the sustainability of this process.
- 22 September 2025
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 59 (38) , 20829-20841
Artificial Laterite from Acid Leaching of Ultramafic Rocks: Mobilization, Enrichment, and Extraction of Critical Metals
Natural weathering of ultramafic rocks produces laterites that host nickel (Ni) and cobalt (Co) which are critical to a renewable energy transition. Here, we performed sulfuric acid leaching on an ultramafic rock, which produces an iron (Fe)-rich residue that concentrates Ni and Co on laboratory time scales, herein termed artificial laterite. Nickel and Co in the artificial laterite are up to 5 - 7 times enriched relative to the raw material and close to their cutoff grades of natural laterite ores. The most Ni-and Co-rich artificial laterite is dominated by poorly crystalline ferrihydrite as revealed by synchrotron-based powder diffraction (PD) and X-ray absorption spectroscopy (XAS, Fe K-edge). By reacting this artificial laterite with aqueous Fe(II) at circumneutral pH and ambient temperature, release of structurally bound Ni and Co is markedly enhanced. Followed by mild acid extraction, total recovery of Ni and Co is around 80%. Meanwhile, impurities such as coprecipitated silica with ferrihydrite would not negatively impact metal release. Our work demonstrates that acid leaching of ultramafic source rocks can generate artificial laterites that are more reactive than their natural counterparts. Furthermore, leaching of these rocks releases magnesium (Mg), an important cation for carbon mineralization, potentially offsetting carbon emissions during metal extraction.
- 22 September 2025
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 59 (38) , 20829-20841
Artificial Laterite from Acid Leaching of Ultramafic Rocks: Mobilization, Enrichment, and Extraction of Critical Metals
Natural weathering of ultramafic rocks produces laterites that host nickel (Ni) and cobalt (Co) which are critical to a renewable energy transition. Here, we performed sulfuric acid leaching on an ultramafic rock, which produces an iron (Fe)-rich residue that concentrates Ni and Co on laboratory time scales, herein termed artificial laterite. Nickel and Co in the artificial laterite are up to 5 - 7 times enriched relative to the raw material and close to their cutoff grades of natural laterite ores. The most Ni-and Co-rich artificial laterite is dominated by poorly crystalline ferrihydrite as revealed by synchrotron-based powder diffraction (PD) and X-ray absorption spectroscopy (XAS, Fe K-edge). By reacting this artificial laterite with aqueous Fe(II) at circumneutral pH and ambient temperature, release of structurally bound Ni and Co is markedly enhanced. Followed by mild acid extraction, total recovery of Ni and Co is around 80%. Meanwhile, impurities such as coprecipitated silica with ferrihydrite would not negatively impact metal release. Our work demonstrates that acid leaching of ultramafic source rocks can generate artificial laterites that are more reactive than their natural counterparts. Furthermore, leaching of these rocks releases magnesium (Mg), an important cation for carbon mineralization, potentially offsetting carbon emissions during metal extraction.
- 16 September 2024
- Published by Elsevier in Environmental Pollution
- Vol. 363 (Pt 1) , 124982
Role of coal ash morphology and composition in delivery and transport of trace metals in the aquatic environment
- 16 September 2024
- Published by Elsevier in Environmental Pollution
- Vol. 363 (Pt 1) , 124982
Role of coal ash morphology and composition in delivery and transport of trace metals in the aquatic environment
- 9 May 2024
- Published by American Chemical Society (ACS) in Environmental Science & Technology Letters
- Vol. 11 (6) , 604-610
Tracing the Environmental Effects of Mineral Fertilizer Application with Trace Elements and Strontium Isotope Variations
- 9 May 2024
- Published by American Chemical Society (ACS) in Environmental Science & Technology Letters
- Vol. 11 (6) , 604-610
Tracing the Environmental Effects of Mineral Fertilizer Application with Trace Elements and Strontium Isotope Variations
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Water Quality Implications of the Neutralization of Acid Mine Drainage with Coal Fly Ash from India and the United States
Subsurface coal mining often induces the formation of acid mine drainage (AMD) in active and abandoned coal mines while coal combustion generates coal combustion residuals (CCR), including fly ash (FA), with elevated levels of toxic metals. Decades of AMD and CCR production have caused major environmental and human health impacts. Given the typically elevated level of oxides in FA, previous studies have examined its potential to neutralize AMD and remove the associated metals. While the neutralization of AMD through reaction with FA has been demonstrated to successfully remove cationic metals, the fate of oxyanion forming elements are less well studied and is the focus of this study. Here we conducted 49 different experiments in which simulated AMD solutions were interacted with representative U.S. (n=7) and Indian (n=6) FA samples through controlled liquid to solid ratios in short-term (24h) and long-term (up to 5 weeks) lab-scale experiments. We show that Class-F FA, originating from Gondwana and Northeast Indian coals, has limited neutralization capacity, while Class-C FA, with high CaO and MgO content from Powder River coals in the U.S., has the greatest AMD neutralization capacity among the studied ashes. The neutralization experiments show that AMD-FA reactions cause removal of cationic elements (i.e., Fe, Mn, and Al) from solution, while at the same time, leaching oxyanion forming elements (i.e., As, Se, Mo, Cr, B, Tl, and Sb) from the FA, increasing the potential environmental risks from the treated leachates. The magnitude of mobilization of these elements depends on their concentrations in the FA and the pH conditions. We show that using FA from the Appalachian and Illinois coals efficiently neutralizes AMD, but also results in a solution that has high concentrations of oxyanion forming elements, which could contaminate the ambient environment, whereas neuralization with Powder River Basin Class-C FA induces only limited contamination.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessWater Quality Implications of the Neutralization of Acid Mine Drainage with Coal Fly Ash from India and the United States
Subsurface coal mining often induces the formation of acid mine drainage (AMD) in active and abandoned coal mines while coal combustion generates coal combustion residuals (CCR), including fly ash (FA), with elevated levels of toxic metals. Decades of AMD and CCR production have caused major environmental and human health impacts. Given the typically elevated level of oxides in FA, previous studies have examined its potential to neutralize AMD and remove the associated metals. While the neutralization of AMD through reaction with FA has been demonstrated to successfully remove cationic metals, the fate of oxyanion forming elements are less well studied and is the focus of this study. Here we conducted 49 different experiments in which simulated AMD solutions were interacted with representative U.S. (n=7) and Indian (n=6) FA samples through controlled liquid to solid ratios in short-term (24h) and long-term (up to 5 weeks) lab-scale experiments. We show that Class-F FA, originating from Gondwana and Northeast Indian coals, has limited neutralization capacity, while Class-C FA, with high CaO and MgO content from Powder River coals in the U.S., has the greatest AMD neutralization capacity among the studied ashes. The neutralization experiments show that AMD-FA reactions cause removal of cationic elements (i.e., Fe, Mn, and Al) from solution, while at the same time, leaching oxyanion forming elements (i.e., As, Se, Mo, Cr, B, Tl, and Sb) from the FA, increasing the potential environmental risks from the treated leachates. The magnitude of mobilization of these elements depends on their concentrations in the FA and the pH conditions. We show that using FA from the Appalachian and Illinois coals efficiently neutralizes AMD, but also results in a solution that has high concentrations of oxyanion forming elements, which could contaminate the ambient environment, whereas neuralization with Powder River Basin Class-C FA induces only limited contamination.
- Open Access
- 1 January 2021
- Published by Tech Science Press in Computer Modeling in Engineering & Sciences
- Vol. 127 (2) , 549-574
Fatigue Crack Propagation Analysis of Orthotropic Steel Bridge with Crack Tip Elastoplastic Consideration
Due to the complex structure and dense weld of the orthotropic steel bridge deck (OSBD), fatigue cracks are prone to occur in the typical welding details. Welding residual stress (WRS) will cause a plastic zone at the crack tip. In this paper, an elastoplastic constitutive model based on the Chaboche kinematic hardening model was introduced, and the extended finite element method (XFEM) was used to study the influence of material elastoplasticity and crack tip plastic zone on the law of fatigue crack propagation. By judging the stress state of the residual stress field at the crack tip and selecting different crack propagation rate models to investigate the crack propagation law when plastic deformation was considered, the propagation path and propagation rate of fatigue crack of the OSBD were obtained. The results show that, whether the residual stress field is considered or not, the plastic deformation at the crack tip will not cause the obvious closure of the fatigue crack at the U-rib toe during the crack propagation process, but will significantly affect the crack propagation path. When material plasticity is considered, the propagation angle of fatigue crack at the U-rib toe basically remains unchanged along the short-axis direction of the initial crack, but is going up along the long-axis direction, and the crack tip plastic zone inhibits the propagation of the crack tip on one side. Compared with linear elastic materials, the crack propagation law considering material plasticity is more consistent with that in actual bridge engineering. In terms of the propagation rate, if the residual stress field is not considered, the fatigue crack propagation rate at U-rib toe with plasticity considered is slightly higher than that without plasticity considered, because plastic deformation will affect the amplitude of energy release rate. When considering the WRS field, the fatigue crack propagation rate at U-rib toe is increased due to the combined actions of plastic deformation and stress ratio R.
- 1 January 2021
- Published by Tech Science Press in Computer Modeling in Engineering & Sciences
- Vol. 127 (2) , 549-574
Open AccessFatigue Crack Propagation Analysis of Orthotropic Steel Bridge with Crack Tip Elastoplastic Consideration
Due to the complex structure and dense weld of the orthotropic steel bridge deck (OSBD), fatigue cracks are prone to occur in the typical welding details. Welding residual stress (WRS) will cause a plastic zone at the crack tip. In this paper, an elastoplastic constitutive model based on the Chaboche kinematic hardening model was introduced, and the extended finite element method (XFEM) was used to study the influence of material elastoplasticity and crack tip plastic zone on the law of fatigue crack propagation. By judging the stress state of the residual stress field at the crack tip and selecting different crack propagation rate models to investigate the crack propagation law when plastic deformation was considered, the propagation path and propagation rate of fatigue crack of the OSBD were obtained. The results show that, whether the residual stress field is considered or not, the plastic deformation at the crack tip will not cause the obvious closure of the fatigue crack at the U-rib toe during the crack propagation process, but will significantly affect the crack propagation path. When material plasticity is considered, the propagation angle of fatigue crack at the U-rib toe basically remains unchanged along the short-axis direction of the initial crack, but is going up along the long-axis direction, and the crack tip plastic zone inhibits the propagation of the crack tip on one side. Compared with linear elastic materials, the crack propagation law considering material plasticity is more consistent with that in actual bridge engineering. In terms of the propagation rate, if the residual stress field is not considered, the fatigue crack propagation rate at U-rib toe with plasticity considered is slightly higher than that without plasticity considered, because plastic deformation will affect the amplitude of energy release rate. When considering the WRS field, the fatigue crack propagation rate at U-rib toe is increased due to the combined actions of plastic deformation and stress ratio R.
- 1 October 2019
- Published by Elsevier in Science of The Total Environment
- Vol. 686, 1090-1103
Evidence for unmonitored coal ash spills in Sutton Lake, North Carolina: Implications for contamination of lake ecosystems
- 1 October 2019
- Published by Elsevier in Science of The Total Environment
- Vol. 686, 1090-1103
Evidence for unmonitored coal ash spills in Sutton Lake, North Carolina: Implications for contamination of lake ecosystems
- Top Cited PapersOpen Access
- 1 February 2019
- Published by Elsevier in International Journal of Coal Geology
- Vol. 203, 1-14
Rare earth elements and yttrium in coal ash from the Luzhou power plant in Sichuan, Southwest China: Concentration, characterization and optimized extraction
- 1 February 2019
- Published by Elsevier in International Journal of Coal Geology
- Vol. 203, 1-14
Top Cited PapersOpen AccessRare earth elements and yttrium in coal ash from the Luzhou power plant in Sichuan, Southwest China: Concentration, characterization and optimized extraction
- 26 October 2016
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 42 (3) , 253-259
Kinetics of Bu-NENA Evaporation from Bu-NENA/NC Propellant Determined by Isothermal Thermogravimetry
- 26 October 2016
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 42 (3) , 253-259
Kinetics of Bu-NENA Evaporation from Bu-NENA/NC Propellant Determined by Isothermal Thermogravimetry