Yong Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yong Zeng has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Jimin Chen
6 shared publications- Jimin Chen
Institute of Laser Engineering, Beijing University of Technology, Beijing 100124, China
6 shared publications Haihua Yao
Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing, People’s Republic of China
2 shared publications- Jimin Chen
Beijing University of Technology
2 shared publications Jun Wang
Peking University People’s Hospital, Musculoskeletal Tumor Center, Beijing, China
2 shared publications- Liying Cheng
Faculty of Materials and Manufacturing Beijing University of Technology 100124 Beijing People's Republic of China
2 shared publications
Latest Publications
- 10 March 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (16) , 10858-10872
Influence of precursor powder characteristics on the microstructure and microwave dielectric properties of vat-photopolymerized Zn2SiO4–TiO2 ceramics
- 10 March 2026
- Published by Springer Nature in Journal of Materials Science
- Vol. 61 (16) , 10858-10872
Influence of precursor powder characteristics on the microstructure and microwave dielectric properties of vat-photopolymerized Zn2SiO4–TiO2 ceramics
- Open Access
- 25 December 2025
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 5 (2)
Data-physics framework embedding machine learning for controllable permeability design and optimization in additive manufacturing
- 25 December 2025
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 5 (2)
Open AccessData-physics framework embedding machine learning for controllable permeability design and optimization in additive manufacturing
- 25 October 2024
- Published by Springer Nature in Journal of Polymer Research
- Vol. 31 (11) , 1-12
Study on the control of mechanical and electrical properties of 3d printed BTO/PDMS flexible porous composites
- 25 October 2024
- Published by Springer Nature in Journal of Polymer Research
- Vol. 31 (11) , 1-12
Study on the control of mechanical and electrical properties of 3d printed BTO/PDMS flexible porous composites
- 23 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
Additive manufacturing of Inconel 718/CuCrZr multi-metallic materials fabricated by laser powder bed fusion
- 23 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
Additive manufacturing of Inconel 718/CuCrZr multi-metallic materials fabricated by laser powder bed fusion
- Open Access
- 1 July 2024
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 13 (7) , 987-1001
Control of electromechanical performance in 3D printing lattice-structured BaTiO 3 piezoelectric ceramics
Barium titanate (BaTiO3) piezoelectric ceramics with triply periodic minimal surfaces (TPMS) structure have been frequently used in filters, engines, artificial bones, and other fields due to their high specific surface area, high thermal stability, and good heat dissipation. However, only a limited amount of studies have analyzed the effect of various parameters such as different wall thicknesses and porosities of TPMS structures on the ceramic electromechanical performance. In this study, we first employed Vat photopolymerization (VPP) 3D printing technology to fabricate high-performance BaTiO3 ceramics. We investigated the slurry composition design and forming process, and designed a stepwise sintering post-processing technique to achieve a density of 96.3% and a compressive strength of 250 ± 25 MPa, with the piezoelectric coefficient (d33) reaching 263 pC/N. Subsequently, we explored the influence of three TPMS structures, namely Diamond, Gyroid, and Schwarz P, on the piezoelectric and mechanical properties of the BaTiO3 ceramics, with the Gyroid structure identified as exhibiting optimal performance. Finally, we examined the piezoelectric and mechanical properties of Gyroid structure BaTiO3 ceramics with varying wall thicknesses and porosities, thus enabling the modulation of ceramic electromechanical performance.
- 1 July 2024
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 13 (7) , 987-1001
Open AccessControl of electromechanical performance in 3D printing lattice-structured BaTiO 3 piezoelectric ceramics
Barium titanate (BaTiO3) piezoelectric ceramics with triply periodic minimal surfaces (TPMS) structure have been frequently used in filters, engines, artificial bones, and other fields due to their high specific surface area, high thermal stability, and good heat dissipation. However, only a limited amount of studies have analyzed the effect of various parameters such as different wall thicknesses and porosities of TPMS structures on the ceramic electromechanical performance. In this study, we first employed Vat photopolymerization (VPP) 3D printing technology to fabricate high-performance BaTiO3 ceramics. We investigated the slurry composition design and forming process, and designed a stepwise sintering post-processing technique to achieve a density of 96.3% and a compressive strength of 250 ± 25 MPa, with the piezoelectric coefficient (d33) reaching 263 pC/N. Subsequently, we explored the influence of three TPMS structures, namely Diamond, Gyroid, and Schwarz P, on the piezoelectric and mechanical properties of the BaTiO3 ceramics, with the Gyroid structure identified as exhibiting optimal performance. Finally, we examined the piezoelectric and mechanical properties of Gyroid structure BaTiO3 ceramics with varying wall thicknesses and porosities, thus enabling the modulation of ceramic electromechanical performance.
- Open Access
- 4 June 2024
- Published by Springer Nature in Research Square
Study on the control of mechanical and electrical properties of 3D printed BTO/PDMS flexible porous composites
Flexible piezoelectric functional composite materials have the advantages of strong plasticity and good surface adhesion, and show great potential in smart wearable devices, electronic skin and other applications. However, due to the complexity of traditional preparation process, high molding cost and poor air permeability, its further development is limited. Direct ink writing (DIW) 3D printing technology is a rapid prototyping technology, with higher flexibility, faster manufacturing speed and lower manufacturing costs, is widely used in metal, ceramic and composite material molding. In this work, a slurry system with polydimethylsiloxane (PDMS) as binder and Barium titanate (BTO) ceramic powder as piezoelectric filler was developed, the printing work of flexible porous BTO/PDMS composite material was completed, and DIW dual-nozzle printing technology was developed. The integrated flexible porous electrode - piezoelectric - electrode functional gradient structure composite was realized. The results show that the BTO/PDMS ink has the characteristics of shear thinning. When the nozzle diameter is 0.5 mm, the printing speed is 650 mm/min, and the BTO mass fraction is 80%, the flexible porous piezoelectric composite with high precision and complex structure is printed. By phase analysis of BTO/PDMS, it is found that the sample has the characteristic peak of BTO. The microstructure analysis shows that the surface of the sample has good structural fidelity and there are a few island-like pores in the interior. The mechanical test shows that the maximum tensile strength of the sample is 1.33 MPa, the elastic modulus is 1.72 MPa, the longitudinal piezoelectric coefficient d33 is 4.37 Pc/N, and the open circuit voltage VOC is 3.17 V. This work demonstrates a highly attractive method for forming flexible piezoelectric materials with “electrode-piezoelectric-electrode” structures, which, due to its simple operation, time and manufacturing cost savings, proposes solutions to key problems in current 3D ceramic manufacturing technologies.
- 4 June 2024
- Published by Springer Nature in Research Square
Open AccessStudy on the control of mechanical and electrical properties of 3D printed BTO/PDMS flexible porous composites
Flexible piezoelectric functional composite materials have the advantages of strong plasticity and good surface adhesion, and show great potential in smart wearable devices, electronic skin and other applications. However, due to the complexity of traditional preparation process, high molding cost and poor air permeability, its further development is limited. Direct ink writing (DIW) 3D printing technology is a rapid prototyping technology, with higher flexibility, faster manufacturing speed and lower manufacturing costs, is widely used in metal, ceramic and composite material molding. In this work, a slurry system with polydimethylsiloxane (PDMS) as binder and Barium titanate (BTO) ceramic powder as piezoelectric filler was developed, the printing work of flexible porous BTO/PDMS composite material was completed, and DIW dual-nozzle printing technology was developed. The integrated flexible porous electrode - piezoelectric - electrode functional gradient structure composite was realized. The results show that the BTO/PDMS ink has the characteristics of shear thinning. When the nozzle diameter is 0.5 mm, the printing speed is 650 mm/min, and the BTO mass fraction is 80%, the flexible porous piezoelectric composite with high precision and complex structure is printed. By phase analysis of BTO/PDMS, it is found that the sample has the characteristic peak of BTO. The microstructure analysis shows that the surface of the sample has good structural fidelity and there are a few island-like pores in the interior. The mechanical test shows that the maximum tensile strength of the sample is 1.33 MPa, the elastic modulus is 1.72 MPa, the longitudinal piezoelectric coefficient d33 is 4.37 Pc/N, and the open circuit voltage VOC is 3.17 V. This work demonstrates a highly attractive method for forming flexible piezoelectric materials with “electrode-piezoelectric-electrode” structures, which, due to its simple operation, time and manufacturing cost savings, proposes solutions to key problems in current 3D ceramic manufacturing technologies.
- Top Cited PapersOpen Access
- 18 January 2024
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 3 (1)
The Applications and Latest Progress of Ceramic 3D Printing
- 18 January 2024
- Published by Elsevier in Additive Manufacturing Frontiers
- Vol. 3 (1)
Top Cited PapersOpen AccessThe Applications and Latest Progress of Ceramic 3D Printing
- Open Access
- 1 January 2024
- Published by Tech Science Press in The International Conference on Computational & Experimental Engineering and Sciences
- Vol. 30 (1) , 1
Recycling of Spent CuCrZr Powder by Laser Powder Bed Fusion: Microstructure Evolution and Properties
In laser powder bed fusion (LPBF), the unmelted powder recovered from the powder bed is degraded due to particle-laser interaction during continuous processing. The sensitivity of LPBF performance and molding quality to powder properties, waste powder is usually discarded after several molding cycles, which increases the cost of raw materials. At the same time, the low laser absorption rate and high thermal conductivity of copper and copper alloys inhibit the complete melting of copper powder prepared by LPBF. Therefore, it is challenging to fabricate copper alloy components with full high density and high conductivity through LPBF. In this paper, a method of treating waste LPBF copper powder by adding graphene and preparing fully dense copper alloy parts with high electrical and thermal conductivity is proposed. This method significantly reduces the high laser reflectivity of copper powder and makes the waste powder recycled. Firstly, the effect of process parameters on the preparation of copper matrix composites by LPBF was studied, and the metallurgical defects were regulated to reveal the densification mechanism of LPBF forming process.The optimal process window was obtained, and the products with relatively crack-free, compactness and excellent performance were realized. The properties of the prepared copper matrix composites reached the properties of the new copper powder. Then, the effects of graphene on the phase, microstructure and properties of copper matrix composites were studied, and the mechanism of graphene reinforced copper matrix composites was analyzed.
- 1 January 2024
- Published by Tech Science Press in The International Conference on Computational & Experimental Engineering and Sciences
- Vol. 30 (1) , 1
Open AccessRecycling of Spent CuCrZr Powder by Laser Powder Bed Fusion: Microstructure Evolution and Properties
In laser powder bed fusion (LPBF), the unmelted powder recovered from the powder bed is degraded due to particle-laser interaction during continuous processing. The sensitivity of LPBF performance and molding quality to powder properties, waste powder is usually discarded after several molding cycles, which increases the cost of raw materials. At the same time, the low laser absorption rate and high thermal conductivity of copper and copper alloys inhibit the complete melting of copper powder prepared by LPBF. Therefore, it is challenging to fabricate copper alloy components with full high density and high conductivity through LPBF. In this paper, a method of treating waste LPBF copper powder by adding graphene and preparing fully dense copper alloy parts with high electrical and thermal conductivity is proposed. This method significantly reduces the high laser reflectivity of copper powder and makes the waste powder recycled. Firstly, the effect of process parameters on the preparation of copper matrix composites by LPBF was studied, and the metallurgical defects were regulated to reveal the densification mechanism of LPBF forming process.The optimal process window was obtained, and the products with relatively crack-free, compactness and excellent performance were realized. The properties of the prepared copper matrix composites reached the properties of the new copper powder. Then, the effects of graphene on the phase, microstructure and properties of copper matrix composites were studied, and the mechanism of graphene reinforced copper matrix composites was analyzed.
- 2 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3053-3065
Indirect forming of alumina-based ceramics by selective laser sintering combined with sol infiltration process and performance study
- 2 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3053-3065
Indirect forming of alumina-based ceramics by selective laser sintering combined with sol infiltration process and performance study