Brian J. Landi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Brian J. Landi has a total of 96 co-authors. Here are the top co-authors by number of shared publications:
- Cory D. Cress
U.S. Naval Research Laboratory, Washington, DC, USA
13 shared publications Jamie E. Rossi
Chemical Engineering Department, Rochester Institute of Technology 1 Lomb Memorial Dr. Rochester NY 14623 USA
11 shared publicationsMatthew J. Ganter
NanoPower Research Laboratory, Rochester Institute of Technology, Rochester, New York, USA
6 shared publicationsChristopher M. Schauerman
NanoPower Research Laboratory, Rochester Institute of Technology, Rochester, New York, USA
5 shared publications- Ivan Puchades
Department of Microsystems Engineering, Rochester Institute of Technology, USA
5 shared publications - Nathanael David Cox
Department of Microsystems Engineering, Rochester Institute of Technology , Rochester, New York 14623, United States
5 shared publications
Latest Publications
- 23 December 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (8)
Free‐Standing, Transparent Carbon Nanotube Thin Films with High Specific Shielding Effectiveness
Carbon nanotubes (CNTs) are emerging as a candidate shielding material for RF technologies due to their multi‐functional properties such as low density, flexibility, and excellent electrical properties. The present work provides a direct comparison of shielding measurements for single‐wall (SWCNT) and multi‐wall (MWCNT) free‐standing thin films fabricated from chlorosulfonic acid dispersions. CNT thin film properties are varied to create a series of thicknesses ranging from ≈18 to ≈4000 nm, resulting in optical transparencies from 80 to 0%. Shielding effectiveness is measured using a rectangular waveguide setup from 10 to 15 GHz and shows frequency‐independence with values up to 50 dB. Lower shielding effectiveness in MWCNT films relative to SWCNT films of equivalent mass is consistent with theoretical studies that propose a restriction of the electromagnetic interaction to the outer MWCNT walls. The present SWCNT and MWCNT films exhibit density‐ and thickness‐specific shielding effectiveness of 3.3 × 106 dB cm2 g−1, a 10× increase over emerging thin film and transparent conductive materials. Demonstration of shielding effectiveness has been made by measuring signal strength reduction from a Bluetooth device when attenuated by the CNT film. Thus, the present work advances the potential to incorporate transparent, conductive CNT films into RF technologies with arbitrary surface geometry.
- 23 December 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (8)
Free‐Standing, Transparent Carbon Nanotube Thin Films with High Specific Shielding Effectiveness
Carbon nanotubes (CNTs) are emerging as a candidate shielding material for RF technologies due to their multi‐functional properties such as low density, flexibility, and excellent electrical properties. The present work provides a direct comparison of shielding measurements for single‐wall (SWCNT) and multi‐wall (MWCNT) free‐standing thin films fabricated from chlorosulfonic acid dispersions. CNT thin film properties are varied to create a series of thicknesses ranging from ≈18 to ≈4000 nm, resulting in optical transparencies from 80 to 0%. Shielding effectiveness is measured using a rectangular waveguide setup from 10 to 15 GHz and shows frequency‐independence with values up to 50 dB. Lower shielding effectiveness in MWCNT films relative to SWCNT films of equivalent mass is consistent with theoretical studies that propose a restriction of the electromagnetic interaction to the outer MWCNT walls. The present SWCNT and MWCNT films exhibit density‐ and thickness‐specific shielding effectiveness of 3.3 × 106 dB cm2 g−1, a 10× increase over emerging thin film and transparent conductive materials. Demonstration of shielding effectiveness has been made by measuring signal strength reduction from a Bluetooth device when attenuated by the CNT film. Thus, the present work advances the potential to incorporate transparent, conductive CNT films into RF technologies with arbitrary surface geometry.
- 3 July 2022
- Published by Taylor & Francis in Biofouling
- Vol. 38 (6) , 593-604
Carbon nanotube survivability in marine environments and method for biofouling removal
The deep sea survivability and biofouling characteristics of corrosion-resistant bulk carbon nanotubes (CNTs) have been studied after deployment in the Atlantic Ocean over the course of 12 months. Quantification of barnacle count, biofouling density, and non-combustible residue shows cyanoacrylate coatings increase durability and reduce the colonization of biofouling compared to as-received CNTs. Scanning electron microscopy was performed on the biofouled CNTs, and the majority of species were identified as diatoms, consisting of an ordered silica cell wall. Both the as-received and cyanoacrylate-treated CNTs were successfully acid purified to remove biogrowth, leading to complete recovery of tensile strength and electrical transport properties. Thermogravimetric analysis, scanning electron microscopy, contact angle, dynamic mechanical analysis, and current carrying capacity measurements validated the refunctionalization results. Thus, the multifunctional property recovery and enhanced durability confirms that CNTs are electrochemically stable in saltwater environments and are resilient to biofouling conditions in real-world environments after extended exposure.
- 3 July 2022
- Published by Taylor & Francis in Biofouling
- Vol. 38 (6) , 593-604
Carbon nanotube survivability in marine environments and method for biofouling removal
The deep sea survivability and biofouling characteristics of corrosion-resistant bulk carbon nanotubes (CNTs) have been studied after deployment in the Atlantic Ocean over the course of 12 months. Quantification of barnacle count, biofouling density, and non-combustible residue shows cyanoacrylate coatings increase durability and reduce the colonization of biofouling compared to as-received CNTs. Scanning electron microscopy was performed on the biofouled CNTs, and the majority of species were identified as diatoms, consisting of an ordered silica cell wall. Both the as-received and cyanoacrylate-treated CNTs were successfully acid purified to remove biogrowth, leading to complete recovery of tensile strength and electrical transport properties. Thermogravimetric analysis, scanning electron microscopy, contact angle, dynamic mechanical analysis, and current carrying capacity measurements validated the refunctionalization results. Thus, the multifunctional property recovery and enhanced durability confirms that CNTs are electrochemically stable in saltwater environments and are resilient to biofouling conditions in real-world environments after extended exposure.
- 21 February 2020
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (15) , 6610-6622
Enhanced copper–carbon nanotube hybrid conductors with titanium adhesion layer
- 21 February 2020
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (15) , 6610-6622
Enhanced copper–carbon nanotube hybrid conductors with titanium adhesion layer
- 4 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (11) , 7340-7349
Sustaining Enhanced Electrical Conductivity in KAuBr4-Doped Carbon Nanotube Wires at High Current Densities
- 4 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (11) , 7340-7349
Sustaining Enhanced Electrical Conductivity in KAuBr4-Doped Carbon Nanotube Wires at High Current Densities
- 6 February 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (2) , 1139
Correction to Effects of Solution Properties on Iodine Monobromide Doping for Enhanced Bulk Carbon Nanotube Electrical Conductivity
- 6 February 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (2) , 1139
Correction to Effects of Solution Properties on Iodine Monobromide Doping for Enhanced Bulk Carbon Nanotube Electrical Conductivity
- 18 December 2018
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (1) , 118-126
High Conductivity Copper–Carbon Nanotube Hybrids via Site-Specific Chemical Vapor Deposition
- 18 December 2018
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (1) , 118-126
High Conductivity Copper–Carbon Nanotube Hybrids via Site-Specific Chemical Vapor Deposition
- 19 June 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 85 (13) , 337-345
Scalable Bath Cell Method for Reversible Lithium Management towards Near Zero Volt Tolerance in Lithium-Ion Cells
Near zero-volt storage is a promising concept to controllably ensure the safety of user-inactive lithium-ion cells during storage or transit. An advantageous method to enable lithium-ion cells to tolerate near zero volt conditions is to manage the amount of reversible lithium ions in a cell such that during near zero volt storage, the potential of each electrode is maintained outside of its damage range. Unlike current commercial methods, this method can be applied to lithium-ion cells in a full range of cell designs (i.e. high power, high energy density) using current state of the art active materials, electrolytes, and current collectors. In the present work, a scalable reversible lithium management technique using a bath cell is demonstrated for the fabrication of a zero-volt tolerant 225 mAh LiNiCoAlO2/MCMB pouch cell. An electrode asymptotic potential (EAP, the potential at which the electrodes asymptote to when the cell is in a near zero volt state) of 2.2 V vs. Li/Li+ was achieved in the final pouch cell as a result of the bath-cell reversible lithium management step. The constructed pouch cell demonstrated ~100% discharge capacity and voltage retention after 14 days at a near zero volt state maintained by an applied resistor. Thus, the bath-cell reversible lithium management method can successfully fabricate reversible lithium managed lithium-ion cells that are highly tolerant to a prolonged (> 1 day) zero volt state.
- 19 June 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 85 (13) , 337-345
Scalable Bath Cell Method for Reversible Lithium Management towards Near Zero Volt Tolerance in Lithium-Ion Cells
Near zero-volt storage is a promising concept to controllably ensure the safety of user-inactive lithium-ion cells during storage or transit. An advantageous method to enable lithium-ion cells to tolerate near zero volt conditions is to manage the amount of reversible lithium ions in a cell such that during near zero volt storage, the potential of each electrode is maintained outside of its damage range. Unlike current commercial methods, this method can be applied to lithium-ion cells in a full range of cell designs (i.e. high power, high energy density) using current state of the art active materials, electrolytes, and current collectors. In the present work, a scalable reversible lithium management technique using a bath cell is demonstrated for the fabrication of a zero-volt tolerant 225 mAh LiNiCoAlO2/MCMB pouch cell. An electrode asymptotic potential (EAP, the potential at which the electrodes asymptote to when the cell is in a near zero volt state) of 2.2 V vs. Li/Li+ was achieved in the final pouch cell as a result of the bath-cell reversible lithium management step. The constructed pouch cell demonstrated ~100% discharge capacity and voltage retention after 14 days at a near zero volt state maintained by an applied resistor. Thus, the bath-cell reversible lithium management method can successfully fabricate reversible lithium managed lithium-ion cells that are highly tolerant to a prolonged (> 1 day) zero volt state.